《FAT_AP_V200R005C10SPC700_Upgrade_Guide.docx》由会员分享，可在线阅读，更多相关《FAT_AP_V200R005C10SPC700_Upgrade_Guide.docx（63页珍藏版）》请在三一办公上搜索。
1、 FAT APV200R005C10SPC700Upgrade GuideIssue01Date2015-05-16HUAWEI TECHNOLOGIES CO., LTD.Copyright Huawei Technologies Co., Ltd. 2015. All rights reserved.No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd
2、.Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.All other trademarks and trade names mentioned in this document are the property of their respective holders.NoticeThe purchased products, services and features are stipulated by the contract made
3、between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided AS IS wit
4、hout warranties, guarantees or representations of any kind, either express or implied.The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommen
5、dations in this document do not constitute a warranty of any kind, express or implied.Huawei Technologies Co., Ltd.Address:Huawei Industrial BaseBantian, LonggangShenzhen 518129Peoples Republic of ChinaWebsite:Issue 01 (2015-05-16)Huawei Proprietary and Confidential Copyright Huawei Technologies Co.
6、, Ltd.i FAT APUpgrade GuideAbout This DocumentAbout This DocumentContentsBefore you upgrade the software, read this upgrade guide. This document is organized as follows:Table 1 ContentsChapterContent1 Before You StartDescribes version requirements before an upgrade, upgrade precautions, and upgrade
7、scenarios.2 Upgrade ProcessDescribes the AP upgrade process.3 Preparing for the UpgradeDescribes AP upgrade preparations.4 Switching a Fit AP to a Fat APDescribes the procedure for switching a Fit AP to a Fat AP.5 Switching a Fat AP to a Fit APDescribes the procedure for switching a Fat AP to a Fit
8、AP.6 Upgrading a Fat AP LocallyDescribes the procedure for upgrading a Fat AP locally.8 Version RollbackProvides methods for AP version rollback.Change HistoryTable 2 Change historyIssueDescriptionDate01This is the first official release.2015-05-16Issue 01 (2015-05-16)Huawei Proprietary and Confiden
9、tial Copyright Huawei Technologies Co., Ltd.iiFAT APUpgrade GuideContentsContentsAbout This Documentii1 Before You Start11.1 Version Requirements11.2 Precautions31.3 Impact of the Upgrade51.4 Upgrade Methods62 Upgrade Process73 Preparing for the Upgrade93.1 Preparing Required Materials and Documents
10、93.2 Prepare required upgrade version file93.3 Setting Up the Upgrade Environment103.4 Checking the device Working Status133.5 Backing Up Files133.6 Upgrading the Upgrade Assistant Package134 Switching a Fit AP to a Fat AP164.1 Method to Switch a Fit AP of V200R003V200R005 to a Fat AP of &V200R00516
11、4.1.1 Upgrading the AP Using Command Lines (Applicable to APs Excluding the AP8x30xN)174.1.2 Upgrading the AP Using Command Lines (Applicable to the AP8x30xN)214.1.3 Upgrading the AP in TFTP Mode in the U-Boot Software234.2 Method to Switch a Fit AP of V200R002 to a Fat AP of V200R005254.2.1 Upgradi
12、ng the AP in TFTP Mode in the U-Boot Software254.3 Method to Switch a Fit AP of V200R001 to a Fat AP of V200R005274.3.1 Upgrading the AP in TFTP Mode in the U-Boot Software275 Switching a Fat AP to a Fit AP305.1 Method to Switch a Fat AP of V200R003&V200R005 to a Fit AP305.1.1 Upgrading the AP Using
13、 Command Lines (Applicable to APs Excluding the AP8x30xN)315.1.2 Upgrading the AP Using Command Lines (Applicable to the AP8x30xN)355.1.3 Using the Upgrade Assistant Package to Upgrade the AP (Applicable to APs Excluding the AP8x30xN)395.1.4 Upgrading the AP in TFTP Mode in the U-Boot Software436 Up
14、grading a Fat AP Locally446.1 Method to Upgrade a Fat AP of V200R003&V200R005 Locally446.1.1 Upgrading the AP Using Command Lines (Applicable to APs Excluding the AP8x30xN and AP9x30xN)456.1.2 Upgrading the AP Using Command Lines (Applicable to the AP8x30xN and AP9x30xN)496.1.3 Using the Upgrade Ass
15、istant Package to Upgrade the AP (Applicable to APs Excluding the AP8x30xN and AP9x30xN)526.1.4 Upgrading the AP in TFTP Mode in the U-Boot Software536.2 Processing Upgrade Failures537 Recovering the AP558 Version Rollback57Issue 01 (2015-05-16)Huawei Proprietary and Confidential Copyright Huawei Te
16、chnologies Co., Ltd.ivFAT APUpgrade Guide1 Before You Start1 Before You Start1.1 Version Requirements1. FAT APs version history. AP6x10xN version historyTable 1-1 AP6x10xN version historyVersionRelease DateUpgrade NoteAP6x10xN V200R003C002013-05-15It can be directly upgraded to V200R005C10SPC700.AP6
17、x10xN V200R003C00SPC1002013-07-15AP6x10xN V200R003C00SPC2002013-09-15AP6x10xN V200R003C00SPC3002013-11-08AP6x10xN V200R003C00SPC5002014-02-13AP6x10xN V200R005C002014-01-15AP6x10xN V200R005C00SPC1002014-02-10AP6x10xN V200R005C00SPC2002014-05-04AP6x10xN V200R005C00SPC6002014-07-30AP6x10xN V200R005C102
18、014-09-16AP6x10xN V200R005C10SPC2002014-12-22 AP3x10xN version historyTable 1-2 AP3x10xN version historyVersionRelease DateUpgrade NoteAP3x10xN V200R003C002013-05-15It can be directly upgraded to V200R005C10SPC700.AP3x10xN V200R003C00SPC1002013-07-15AP3x10xN V200R003C00SPC2002013-09-15AP3x10xN V200R
19、003C00SPC3002013-11-08AP3x10xN V200R003C00SPC5002014-02-13AP3x10xN V200R005C002014-01-15AP3x10xN V200R005C00SPC1002014-02-10AP3x10xN V200R005C00SPC2002014-05-04AP3x10xN V200R005C00SPC6002014-07-30AP3x10xN V200R005C102014-09-16AP3x10xN V200R005C10SPC2002014-12-22 AP5x10xN version historyTable 1-3 AP5
20、x10xN version historyVersionRelease DateUpgrade NoteAP5x10xN V200R003C002013-05-15It can be directly upgraded to V200R005C10SPC700.AP5x10xN V200R003C00SPC1002013-07-15AP5x10xN V200R003C00SPC2002013-09-15AP5x10xN V200R003C00SPC3002013-11-08AP5x10xN V200R003C00SPC5002014-02-13AP5x10xN V200R005C002014-
21、01-15AP5x10xN V200R005C00SPC1002014-02-10AP5x10xN V200R005C00SPC2002014-05-04AP5x10xN V200R005C00SPC6002014-07-30AP5x10xN V200R005C102014-09-16AP5x10xN V200R005C10SPC2002014-12-22 AP5x30xN version historyTable 1-4 AP5x30xN version historyVersionRelease DateUpgrade NoteAP5x30xN V200R005C00SPC2002014-
22、05-04It can be directly upgraded to V200R005C10SPC700.AP5x30xN V200R005C00SPC6002014-07-30AP5x30xN V200R005C102014-09-16AP5x30xN V200R005C10SPC2002014-12-22 AP7x10xN version historyTable 1-5 AP7x10xN version historyVersionRelease DateUpgrade NoteAP7x10xN V200R005C102014-09-16It can be directly upgra
23、ded to V200R005C10SPC700.AP7x10xN V200R005C10SPC2002014-12-22 AP8x30xN version historyTable 1-6 AP8x30xN version historyVersionRelease DateUpgrade NoteAP8x30xN V200R005C102014-09-16It can be directly upgraded to V200R005C10SPC700.AP8x30xN V200R005C10SPC2002014-12-22 AP9x30xN version historyTable 1-7
24、 AP9x30xN version historyVersionRelease DateUpgrade NoteAP9x30xN V200R005C102014-09-16It can be directly upgraded to V200R005C10SPC700.AP8x30xN V200R005C10SPC2002014-12-22AP8x30xN V200R005C10SPC3002015-03-281.2 Precautions1. Upgrade Restrictions The WDS and mesh networking do not support the followi
25、ng upgrade scenarios: Upgrading a fat AP to a fat AP Switching a fat AP to a fit AP Switching a fit AP to a fat AP In the CLI mode, a Fit AP of V200R001 or V200R002 cannot be directly switched to a Fat AP of V200R005. You must upgrade the Fit AP to V200R003 or V200R005 first and then switch the Fit
26、AP V200R003 or V200R005 to a Fat V200R005. For details, see FIT AP V200R005C10SPC700 (& AC) Upgrade Guide and 4.1 Method to Switch a Fit AP of V200R003V200R005 to a Fat AP of &V200R005. The U-Boot mode does not have this limitation If the fat AP upgrade fails, the AP cannot properly start. You can r
27、oll back the AP to the original version only in U-Boot mode, but not in CLI mode. A fat AP does not support the upgrade using HTTP on a web platform. After a fit AP switches to a fat AP, the fat AP automatically recovers factory settings. Therefore, you need to re-configure the Fat AP after the swit
28、ching. After a fat AP switches to a fit AP, the fit AP automatically recovers factory settings. Before switching a fat AP to a fit AP, complete basic online configurations of the fit AP on the AC. The fit AP directly goes online after the switching.Table 1-8 Upgrade scenario restrictionsUpgrade Type
29、Remote UpgradeUpgrade in AC ModeBatch UpgradeAP Upgrade in WDS or Mesh NetworkingVersion Rollback When the Upgrade Using the Flash Memory Fails (U-Boot Works Properly)Switching a fit AP to a fat APNoNoNoNoNoSwitching a fat AP to a fit APYesNOTEThis feature is not supported in V200R003C00 and V200R00
30、3C00SPC100.NoNoNoNoUpgrading a fat AP to a fat APYesNOTEThis feature is not supported in V200R003C00 and V200R003C00SPC100.NoNoNoNoStarting from V200R003C00SPC200, an AP upgrade using command lines is applicable to two remote upgrade scenarios: switching a fat AP to a fit AP and upgrading a fat AP t
31、o a target version. To upgrade APs remotely, the networking environment must meet certain requirements. For details, see 3.3 Setting Up the Upgrade Environment.Uboot-based AP upgrade is not applicable to remote upgrade scenarios.2. AP6x10xN V200R005C10SPC700 applies to AP6010SN-GN, AP6010DN-AGN, AP6
32、510DN-AGN, AP6610DN-AGN, AP6610DN-AGN-US and AP6510DN-AGN-US APs.AP3x10xN V200R005C10SPC700 applies to AP3010DN-AGN. AP5x10xN V200R005C10SPC700 applies to AP5010SN-GN and AP5010DN-AGN APs.AP5x30xN V200R005C10SPC700 applies to AP5030DN and AP5130DN APs.AP7x10xN V200R005C10SPC700 applies to AP7110DN-A
33、GN APs.AP8x30xN V200R005C10SPC700 applies to AP8030DN and AP8130DN APs.AP9x30xN V200R005C10SPC700 applies to AP9130DN.Table 1-7 shows the mapping between AP models and software version files.Table 1-9 Mapping between AP models and software version filesAP ModelSoftware Version FileAP6010SN-GN, AP601
34、0DN-AGN, AP6510DN-AGN, AP6610DN-AGN, AP6510DN-AGN-US, AP6610DN-AGN-USFatAP6X10XN_V200R005C10SPC700.binAP3010DN-AGNFatAP3X10XN_V200R005C10SPC700.binAP5010SN-GN, AP5010DN-AGNFatAP5X10XN_V200R005C10SPC700.binAP5030DN, AP5130DNFatAP5X30XN_V200R005C10SPC700.binAP7110DN-AGNFatAP7X10XN_V200R005C10SPC700.bi
35、nAP8030DN, AP8130DNFatAP8X30XN_V200R005C10SPC700.binAP9130DNFatAP9X30XN_V200R005C10SPC700.bin1.3 Impact of the UpgradeImpact on the System During the UpgradeImpact on ServicesDuring an AP upgrade, services are interrupted for about 20 minutes. The data is the test data in the lab. The actual AP upgr
36、ade time depends on the network environment.Impact on Network CommunicationWhen the system restarts, the communication between the switch and the NMS is interrupted. The communication interruption time is the same as the service interruption time.Impact on the System After the Upgradel The Telnet fu
37、nction is disabled, but the STelnet function is enabled in the factory settings.After a device of V200R005C00SPC200 or an earlier version is upgraded to V200R005C10 or later, the Telnet function is disabled in the factory settings. After factory settings of the device are restored, you need to enabl
38、e the Telnet function first for Telnet login to the device or you can directly log in to the device using STelnet.You can run the telnet server enable command in the system view to enable Telnet on a Fat AP. system-view Huawei telnet server enableTo enable Telnet on a Fit AP, log in to the AC, run t
39、he telnet enable command in the AP profile view, and deliver the configuration. In the following example, the command is run in the default AP profile view. system-view Huawei wlan Huawei-wlan-view ap-profile id 0 Huawei-wlan-ap-prof-ap-profile-0 telnet enable Huawei-wlan-ap-prof-ap-profile-0 quit H
40、uawei-wlan-view commit all 1.4 Upgrade MethodsAP upgrade scenarios:l Local upgradeAC upgrade methods:l CLI-based upgradel U-Boot upgradel Manual upgrade using the upgrade assistant software packageThis upgrade method is not supported in V200R003C00SPC200 and a later version.CLI-based UpgradeWhen an
41、AP is working properly, you can upgrade the AP using the CLI. The upgrade procedure in this mode is simple. The CLI-based upgrade mode is recommended.Manual Upgrade Using the Upgrade Assistant Software PackageWhen the CLI-based upgrade fails, manually upgrade an AP using the upgrade assistant softwa
42、re package. However, this mode is not recommended.U-Boot UpgradeIf the AP fails to start and cannot be upgraded using the CLI or the upgrade assistant software package, upgrade the AP using U-Boot. Using U-Boot to upgrade the AP is complex and must be implemented by strictly following the upgrade in
43、structions. This mode is not recommended.Issue 01 (2015-05-16)Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd.7FAT APUpgrade Guide2 Upgrade Process2 Upgrade ProcessThe AP8030DN and AP8130DN do not support an upgrade assistant package; therefore, you do not need to upgrade
44、or verify the upgrade assistant package. Skip this step in an upgrade process.Figure 2-1 Flowchart for upgrading a fat AP locally and switching the fat AP to a fit APFigure 2-2 Flowchart for switching a fit AP to a fat APIssue 01 (2015-05-16)Huawei Proprietary and Confidential Copyright Huawei Techn
45、ologies Co., Ltd.9FAT APUpgrade Guide3 Preparing for the Upgrade3 Preparing for the Upgrade3.1 Preparing Required Materials and DocumentsTable 3-1 Required materials and documentsNo.ItemRemarks1PC running Windows2Upgrade reference documents3Upgrade version file5 Switching a Fat AP to a Fit AP requir
46、es FitAP6X10XN_V200R005C10SPC700.bin4 Switching a Fit AP to a Fat AP and 6 Upgrading a Fat AP Locally require FatAP6X10XN_V200R005C10SPC700.bin4TFTP, FTP or SFTP server programs installed on the PC5ACs IP address, user name, and password6Telnet tool7Network cable and serial cable3.2 Prepare required upgrade version fileTable 3-2 Required upgrade version fileNo.FileF
