《17025批准的项目.docx》由会员分享，可在线阅读，更多相关《17025批准的项目.docx（106页珍藏版）》请在三一办公上搜索。
1、ISO/IEC 17025 认可证书 CNAS-PD19/06-A/3 中国合格评定国家认可委员会认 可 证 书 附 件（注册号：CNAS L2761）名称: 江西省计量测试研究院 地址：江西省南昌市站南街45号签发日期：2011年08月03日 有效期至：2014年08月02日更新日期：2011年08月03日附件1 认可的检测能力范围序号检测对象项目/参数领域代码检测标准（方法）名称及编号（含年号）限制范围说明序号名称1游标卡尺1部分参数1303GB/T21389-2008游标带表和数显卡尺不测:材料2外径千分尺1部分参数1303GB/T 1216-2004外径千分尺不测:材料3刀口尺1部分参
2、数1303GB/T 6091-2004刀口形直尺不测:材料4焦度计1全部参数17GB 17341-1998光学和光学仪器焦度计5验光机1部分参数1309ISO10342:2003眼科设备-验光机只测:零位示值、球镜顶焦度示值、出瞳光照度6经纬仪1部分参数1309GB/T 3161-2003光学经纬仪不测:望远镜分辨力、透过系数、成像质量7水准仪1部分参数1309GB/T 10156-1997水准仪不测:望远镜分辨力、透过系数、成像质量8验光镜片1全部参数17GB 17342-2009眼科仪器验光镜片9数字温度指示调节仪1部分参数1501JB/T 8386.1-1996工业过程测量和控制系统用模
3、拟输入数字式指示控制仪第一部分：两位或多位输出仪表GB/T13639-2008工业过程测量和控制系统用模拟输入数字式指示仪不测:外界磁场、串、共模干扰、辐射电磁场、静电放电10体温计1全部参数1501GB 1588-2001玻璃体温计11温湿度培养箱1全部参数1504JB/T5520-1991干燥箱技术条件GB/T10586-2006湿热试验箱技术条件YY0027-1990电热恒温培养箱12工作用温度计1部分参数1501JB/T 9264-1999电接点玻璃温度计JB/T 9259-1999蒸汽和气体压力式温度计JB/T 9262-1999工业玻璃温度计和实验玻璃温度计JB/T 8803-19
4、98双金属温度计不测:寿命试验稳定性、长期运行试验13电子计价秤1秤量准确度1311GB/T77222005电子台案秤2示值稳定性3偏载4鉴别力5重复性6最大安全载荷7回秤8倾斜9安全性能14非自行指示秤1秤量准确度1311GB/T335-2002非自行指示秤2灵敏度3偏载4重复性14非自行指示秤5倾斜1311GB/T335-2002非自行指示秤6最大安全载荷7硬度15砝码1质量1310GB/T 4167-19841-5等砝码16非自动天平杠杆式天平1计量性能1311GB/T4168-1992非自动天平 杠杆式天平2游码与链条天平的秤量误差3机械加(减)码4减幅系数5水准器和重锤17转速表1转
5、速1324JB/T 5221-1991接触式手持数字转速表JB/T 871-1992模拟指示式转速表(中文)18标准测力仪1外观标识1323GB/T 13634-2008单轴试验机检验用标准测力仪的校准2分辨力3复现性和重复性4零点5进回程19机电式有功电能表1准确度要求0410GB/T 17215.311-2008交流电测量设备 特殊要求第11部分：机电式有功电能表(0.5、1和2级)不测:冲击电压、短时过电流试验、弹簧锤试验、电磁兼容试验、阳光辐射试验、防尘和防水试验、耐热和阻燃试验2电气要求3气候影响试验4交流电压试验20直接作用模拟指示电测量仪表1基本误差试验0410GB/T 7676
6、.12-1998GB/T 7676.9-1998直接作用模拟指示电测量仪表及其附件； 推荐的试验方法不测:交流被测量的畸变2改变量试验3过冲试验4连续过负载试验5自热试验21模拟示波器（性能测试）1偏转系数误差0413GB/T 6585-1996阴极射线示波器通用规范2时间系数误差3校准信号4（V）电压22晶体振荡器1开机特性0412GB/T 12274-1990石英晶体振荡器总规范2日频率波动31s频率稳定度4频率复现性23秒表1时段测量精度0412GB/T 22773-2008机械秒表GB/T 22778-2008液晶数字式石英秒表2瞬时日差3延续走时24超声诊断仪1输出声强1401.03
7、GB9706.9-2008医用电气设备 第2-37部分超声诊断和监护设备安全专用要求2侧（横）、轴（纵）向分辨力GB10152-2009 B型超声诊断设备3盲区、探测深度4几何位置示值误差25水表1.外观标识1316GB778.13-2007封闭满管道中水流量的测量 饮用冷水水表和热水水表：规范、安装要求、试验方法和试验设备只测:(1550)mm2静压3示值误差4水压5逆流6压力损失7流速场不规则性8Q3下的连续流量耐久性26煤气表1全部参数1316GB/T6968-1997膜式煤气表只测:(0.0166.0)m3/h27小容量玻璃量器1全部参数1312GB/T1280312810.1991实
8、验室玻璃仪器只测:(0.12000)mlA、B级28一次性输液器1部分参数1312GB18458.2-2003一次性输液器不测:微粒含量、化学要求、生物要求29一次性注射器1部分参数1312GB15810-2001一次性注射器不测:材质、化学性能、滑动性能、器身密合性以及包装No. CNAS L2761 第 8 页 共 106 页 The scope of the accreditation in Chinese remains the definitive version.ISO/IEC 17025 认可证书 CNAS-PD19/06-A/3 CHINA NATIONAL ACCREDITA
9、TION SERVICE FOR CONFORMITY ASSESSMENTAPPENDIX OF ACCREDITATION CERTIFICATE(Registration No. CNAS L2761) NAME: Jiangxi Institute of Measurement and Testing ADDRESS: No.45, Zhannanjie, Nanchang, Jiangxi, ChinaDate of Issue: 2011-08-03 Date of Expiry: 2014-08-02Date of Update：2011-08-03APPENDIX 1 SCOP
10、E OF ACCREDITED TESTINGTest ObjectItem/ParameterCode of Field Title, Code of Standard or Method Limitation NoteItem/ Parameter1Vernier Caliper1Partial parameters1303GB/T21389-2008Vernier,dial and digital display calipersExcept for material item2Outside micrometer1Partial parameters1303GB/T 1216-2004
11、Outside micrometerExcept for material item3Straight Edge1Partial parameters1303GB/T 6091-2004Straight EdgeExcept for material item4Focimeters1All parameters17GB 17341-1998Optics and optical instruments-Focimeters5Eye refractometers1Partial parameters1309ISO10342:2003Ophthalmic instrumnets-Eye refrac
12、tometersAccredited only for zero value、spherical mirror focal value、illuminase of exit pupil6Theodolite1Partial parameters1309GB/T 3161-2003Optical TheodoliteExcept for Telescope resolution、transmit parameters、Image Quality7Level1Partial parameters1309GB/T 10156-1997LevelsExcept for Telescope resolu
13、tion、transmit parameters、Image Quality8Trial case lenses1All parameters17GB 17342-2009Ophthalmic instrument-Trial case lenses9Digital temperature indicators and controllers1Partial parameters1501JB/T 8386.1-1996Part one of Digital indicator controls with analogue input for use in industrial-process
14、measurement and control systems：two-bit or multi-bit output metersGB/T 13639-2008Digital indicators with analogue input for use in industrial-process measurement and control systemsExcept for field strength external, common-mode interference test， electromagnetic radiation and electrostatic discharg
15、e10Thermometers1All parameters1501GB 1588-2001Clinical thermometer11Temperature tester box1All parameters1504JB/T5520-1991Technical conditions for Glove boxesGB/T10586-2006Specification for damp heat test chambersYY0027-1990Electric heating thermostatic breed box12Industrial thermometer1Partial para
16、meters1501JB/T 9264-1999Electric contact glass thermometerJB/T 9259-1999Vapor pressure and gas filled thermometersJB/T9262-1999Liquid-in-glass industrial thermometer and laboratorial thermometersJB/T 8803-1998Bimetal thermometerExcept for lifespan test, stabilization and long-tern running test13Elec
17、tronic charge scale1Accuracy of weighing1311GB/T77222005Electronic charge scale2Stability of indication3Deflection load4Discriminate capability5Repeatability6Maximal load of safety7Return value8Lean9Safety capability14Non- automatic display scale1Veracity of weighing1311GB/T335-2002Non-automatic dis
18、play scale2Sensitivity3Deflection4Repeatability5Lean6Maximal load of safety7Rigidity15weight1Mass1310GB/T 4167-1984Class 1-5 weights16Non-automatic balance-Beam balance1Measure capability1311GB/T4168-1992Non-automatic balance-Beam balance2Weighting error of the locomotive weight and chain scale3Mech
19、anical add(decrease) weight4Minus extent coefficient5Water level and heavy hammer17Tachometer1Rotation rate1324JB/T 5221-1991Contact handset digital tachometerJB/T 871-1992Simulated indicated tachometer18Standard dynamometer1Appearance1323GB/T 13634-2008Calibration of force-proving insturments used
20、for the verification of uniaxial testing machines2resolution3reproducibility4zero point5forward and backward19Electromechanical meter for active energy1Accuracy requirements0410GB/T 17215.311-2008Electricity metering equipment(a.c) - Particular Requirements - Part 11: Electromechanical meter for act
21、ive energy(classes0.5、1and2)Except for impulse voltage; short time over current test; Spring Hammer and Electromagnetic compatibility test2Electrical requirements19Electromechanical meter for active energy3Climate Impact Test0410GB/T 17215.311-2008Electricity metering equipment(a.c) - Particular Req
22、uirements - Part 11: Electromechanical meter for active energy(classes0.5、1and2)Except for impulse voltage; short time over current test; Spring Hammer and Electromagnetic compatibility test4AC voltage test20Direct acting indicating analogue electrical measuring instruments1Basicerror test0410GB/T 7
23、676.12-1998GB/T 7676.9-1998Direct acting indicating analogue electrical measuring instruments and their accessories-Definitions and general requirements common to all parts； Special requirements for ammeters and voltmeters；Recommended test methodsExcept for the distortion of alternating component2Va
24、riation test20Direct acting indicating analogue electrical measuring instruments3Overshoot test0410GB/T 7676.12-1998GB/T 7676.9-1998Direct acting indicating analogue electrical measuring instruments and their accessories-Definitions and general requirements common to all parts； Special requirements
25、for ammeters and voltmeters；Recommended test methodsExcept for the distortion of alternating component4Continuous over-load test5Self-heating test21Analog oscilloscope (character test)1Uprightness deflection system413GB/T 6585-1996General specification for cathode ray oscilloscopes2Level deflection
26、system3Calibration signal21Analog oscilloscope (character test)4（V）voltage413GB/T 6585-1996General specification for cathode ray oscilloscopes22Crystalloid oscillation1Opening characteristic0412GB/T 12274-1990Quartz crystal controlled oscilloscopes2Frequency fluctuation of1 day3Frequency stability o
27、f1 second4Frequency repeatability23Stopwatch1Time measure precision0412GB/T 22773-2008StopwatchGB/T 22778-2008LCD digital quartz stopwatch2Precision of 1 second3Voltage coefficient24Ultrasonic diagnostic equipment1Ultrasonic strength output1401.03GB9706.9-2008 Medical electrical equipment - Part 2-3
28、7: Particular requirements for the safety of ultrasonic medical diagnostic and monitoring equipment2Transverse vertical resolving powerGB10152-2009 B mode ultrasonic diagnostic equipment3Blind district detect depth4Geometric position display error25Cold potable water1Appearence1316GB778.13-2007Measu
29、rement of water flow in fully charged closed conduitsMeters for cold potable water and hot water- Part 1,2,3specifications,installation requirements,test methods and equipmentAccredited only for Test range：(1550)mm2Static pressure25Cold potable water3indication error1316 GB778.13-2007Measurement of
30、water flow in fully charged closed conduitsMeters for cold potable water and hot water- Part 1,2,3specifications,installation requirements,test methods and equipmentAccredited only for Test range：(1550)mm4Water pressure5reflux6Pressure loss7irregularity in velocity field8Continuous flow endurance un
31、der the Q3 flow point26Gas meters1All parameters1316GB/T6968-1997Diaphragm gas metersAccredited only for Test range：(0.0166.0)m3/h27Little volumetric glassware1All parameters1312GB/T1280312810.1991Laboratory glasswareAccredited only for Test range：(0.12000)mlClass A、B28Sterile hypoderm syringes for
32、single use1Partial parameters1312GB18458.2-2003Sterile hypoderm syringes for single useExcept for particulate content, chemical requirements, biological requirements29Butter-type infusion sets1Partial parameters1312GB15810-2001Butter-type infusion sets for single useExcept for materials, chemical re
33、quirements, Sliding performance, Federated hop Performance of vessels and package中国合格评定国家认可委员会认 可 证 书 附 件（注册号：CNAS L2761）名称: 江西省计量测试研究院 地址：江西省南昌市站南街45号签发日期：2011年08月03日 有效期至：2014年08月02日更新日期：2011年08月03日附件2 认可的校准能力范围序号测量仪器名称校准参量领域代码测量仪器类别规范代号（含年号）名称测量范围扩展不确定度（校准和测量能力，k=2）限制说明备注1量块长度13083等JJG146-2003 量块
34、检定规程(0.5100)mmU=(0.1+1L) m k=2.624等(0.51000)mmU=(0.2+2L) m k=2.622通用卡尺长度1303游标卡尺JJG 30-2002通用卡尺检定规程(0.02500)mmU=0.02 mm L=500mm深度卡尺3高度卡尺长度1303/JJG 31-1999高度卡尺检定规程(0.02500)mmU=0.02 mm L=500mm4千分尺长度1303/JJG 21-2008千分尺检定规程(0.01500)mmU=4.6 m L=500mm5指示表长度1303百分表JJG34-2008指示表(指针式、数显式)检定规程(0.0110) mmU=5.7
35、m L=10mm5指示表长度1303 千分表JJG34-2008指示表(指针式、数显式)检定规程(0.0012)mmU=1.7m L=1mm6平晶长度1303平面平晶JJG28-2000平晶检定规程(D30D100)mm平面度：U=0.02 m D100mm平行平晶(D15D100)mm平面度：U=0.02m D100mm(15100) mm平行度：U=0.2m7刀口形直尺直线度1303/JJG63-2007刀口形直尺检定规程(75500)mmU=1.4m L=500mm8钢直尺长度1303/JJG1-1999钢直尺检定规程(0.51000)mmU=0.1mm L=1000mm9钢卷尺长度13
36、03/JJG4-1999钢卷尺检定规程(2100)mU=0.2 mm L=5m10水平仪 检定器角度1303/JJG 191-2002水平仪检定器检定规程(11.5)mm/mUrel =2.5% =0.5mm/m11框式水平仪和条式水平仪角度1303/JJF 1084-2002框式水平仪和条式水平仪校准规范(11.5)mm/mUrel=6.9% ri=0.16mm/m12塞尺长度1301/JJG62-2007塞尺检定规程(0.021.0)mmU=2.7m L=1.0mm13超声波测厚仪长度1309/JJF 1126-2004超声波测厚仪校准规范(1200)mmU = 0.1mm L=100mm
37、14覆层厚度磁性测量仪长度1309/JJG818-2005磁性、电涡流式覆层厚度测量仪检定规程（11000）mU=1.5m L=1000m15触针式表面粗糙度测量仪粗糙度1309/JJF1105-2003触针式表面粗糙度测量仪校准规范Ra(0.13.2)mUrel=3.4% Ra=0.82m16坐标测量机长度1309/JJF1064-2010坐标测量机校准规范1000mm1500mm1000mmU =(1.3+0.3L/1000)m限制影像测量机17指示类量具检定仪长度1309百分表检定仪JJG201-2008指示类量具检定仪(125)mmU=0.8m L=25mm千分表检定仪(02)mmU=
38、0.3m L=2mm18工具显微镜长度1309/JJG56-2000工具显微镜检定规程(0.001200)mmU=0.8m L=100mm19光学计长度1309/JJG 45-1999光学计检定规程(-100+100)mU=0.1mL=+60m20投影仪长度1309/JJF 1093-2002投影仪校准规范投影屏直径:(2501000)mmU=1.3m L=100mm21测长仪长度1309/JJF 1189-2008测长仪校准规范(0.001100)mmU=0.3mL=100mm22光学经纬仪角度1309/JJG414-2003光学经纬仪检定规程水平：0360U=0.3 =90竖直：30U=0
39、.5 =3023电子经纬仪角度1309/JJG100-2003全站型电子速测仪检定规程水平：0360U=0.3 =90竖直：30U=0.5 =3024水准仪角度1309/JJG425-2003水准仪检定规程30U=1.0 水平位置 安平式25瞳距仪长度1601/JJG952-2000瞳距仪检定规程（5080）mmU=0.4 mm L=55mm26测量内尺寸千分尺长度1309/JJF1091-2002测量内尺寸千分尺校准规范(5100)mmU=0.002mm L=50mm27厚度表长度1309/JJF1255-2010厚度表校准规范（030）mmU=0.005mm L=10mm28标准铂铑10铂热电偶温度1501/JJG75-1995标准铂铑10铂热电偶检定规程（419.5271084
