《AS14292-1998---电缆-聚合绝缘第二部分工作电压大于.docx》由会员分享，可在线阅读，更多相关《AS14292-1998---电缆-聚合绝缘第二部分工作电压大于.docx（55页珍藏版）》请在三一办公上搜索。
1、AS NZS 1429.2-1998Australian/New Zealand Standard澳大利亚/新西兰标准Electric cablesPolymeric insulatedPart 2: For working voltages above 19/33 (36) kV up to and including 76/132 (145) kV电缆聚合绝缘第二部分：工作电压大于19/33 (36) kV时，电力供应小于等于76/132 (145) kVThis Joint Australian/New Zealand Standard was prepared by Joint Tec
2、hnical Committee EL/3, Electric Wires and Cables. It was approved on behalf of the Council of Standards Australia on 17 November 1997 and on behalf of the Council of Standards New Zealand on 17 November 1997. It was published on 5 February 1998.本澳/新联合标准由电线和电缆联合技术委员会EL/3编制，并以澳大利亚标准委员会的名义于1997年11月17日获
3、得审批通过，以新西兰标准委员会的名义于1997年11月17日获得审批通过。并于1998年2月5日出版。The following interests are represented on Committee EL/3:EL/3委员会由以下单位参加:Australasian Railways Association大洋洲铁路委员会Australian Electrical and Electronic Manufacturers Association 澳大利亚电气和电子制造商委员会Department of Defence, Australia澳大利亚国防部Electrical regulat
4、ory authorities电气管理机构Electricity Supply Associated of Australia澳大利亚供电协会Institution of Engineers, Australia澳大利亚工程师协会Ministry of Commerce, New Zealand新西兰商业部New Zealand Electrical Contractors Association新西兰电气承包商协会New Zealand Electrical and Electronic Manufacturers Federation 新西兰电气和电子制造商联盟Office of Ener
5、gy, N.S.W.新南威尔士能源局Testing interests检测机构Review of Standards.标准的审议To keep abreast of progress in industry, Joint Australian/ New Zealand Standards are subject to periodic review and are kept up to date by the issue of amendments or new editions as necessary. It is important therefore that Standards us
6、ers ensure that they are in possession of the latest edition, and any amendments thereto.为了使澳大利亚/新西兰联合标准与业界的科技进步齐肩并进，我们定期对其进行审议，并发布必要的增补修订或通过新的版本，使之不断与时俱进。因此，标准用户务必确保自己拥有最新版本和最新修正的内容。Full details of all Joint Standards and related publications will be found in the Standards Australia and Standards N
7、ew Zealand Catalogue of Publications; this information is supplemented each month by the magazines The Australian Standard and Standards New Zealand, which subscribing members receive, and which give details of new publications, new editions and amendments, and of withdrawn Standards.澳大利亚标准局和新西兰标准局刊
8、发的标准目录涵盖所有联合标准及其相关刊物；这些信息每月由澳大利亚标准和新西兰标准这两本月刊来进行更新。该月刊仅面向订阅会员，内容涉及新刊物、新版本、修订内容以及过时标准的详细信息。Suggestions for improvements to Joint Standards, addressed to the head office of either Standards Australia or Standards New Zealand, are welcomed. Notification of any inaccuracy or ambiguity found in a Joint A
9、ustralian/New Zealand Standard should be made without delay in order that the matter may be investigated and appropriate action taken.欢迎向澳大利亚标准局或新西兰标准局总部提出有关联合标准的改进建议。读者如发现澳大利亚/新西兰联合标准存在任何不准确或含糊不清的内容，请及时告诉我们，以便我们开展调查并采取相应的措施。This Standard was issued in draft form for comment as DR 97035.本标准以草案（DR 97
10、035）形式发布，用于征求公众意见。First published as AS/NZS 1429.2:1998. 首版为AS/NZS 1429.2:1998。PUBLISHED JOINTLY BY:由以下单位联合出版：STANDARDS AUSTRALIA 1 The Crescent,Homebush NSW 2140 AustraliaSTANDARDS NEW ZEALANDLevel 10, Radio New Zealand House, 155 The Terrace, Wellington 6001 New Zealand澳大利亚标准局 (1 The Crescent, Hom
11、ebush NSW 2140 Australia) 新西兰标准局（Level 10, Radio New Zealand House, 155 The Terrace, Wellington 6001 New Zealand）PREFACE前言This Standard was prepared by the Joint Standards Australia/Standards New Zealand Committee EL/3, Electric Wires and Cables, to complement AS 1429.1 1993, Electric cablesPolymeri
12、c insulated, Part 1: For working voltages 1.9/3.3(3.6) kV up to and including 19/33(36) kV.本标准由澳大利亚标准局/新西兰标准局电线和电缆联合委员会EL/3编制，用以补充AS 1429.1 1993，电缆聚合绝缘，第一部分：工作电压1.9/3.3(3.6) kV下，电力供应小于等于19/33(36) kV。The objective of this Standard is to specify requirements for single-core cross-linked polyethylene i
13、nsulated cables for fixed installations operating at voltages above 19/33(36) kV up to and including 76/132(145) kV.本标准对19/33(36) kV以上电压下运行的小于等于76/132(145) kV的单芯交联聚乙烯绝缘电缆的固定安装提出了要求。In the preparation of this Standard, consideration was given to the following publications and acknowledgment is made o
14、f the assistance received:本标准编制过程中，参考了下列几项标准并接受了帮助：IEC229 Tests on cable oversheaths which have a special protective function and are applied by extrusion 电缆外护套测试，该外护套具有特殊保护功能且通过挤压应用502 Extruded solid dielectric insulated power cables for rated voltages from 1 kV up to 30 kV 额定电压1 kV 至 30 kV的挤压式固体介质
15、绝缘电力电缆840 Tests for power cables with extruded insulation for rated voltages above 30 kV (Um=36kV)upto 150kV(Um= 170kV) 对额定电压30 kV (Um=36kV)至50kV(Um= 170kV)的挤压绝缘电力电缆的测试811 Common test methods for insulating and sheathing materials of electric cables (all parts) 电缆绝缘及护套材料的普通测试法（所有部分）AEICCS7 Specifica
16、tions for crosslinked polyethylene insulated shielded power cables rated 69 through 138 kV 额定电压69 至138 kV的交联聚乙烯绝缘屏蔽电力电缆规范The nominal cross-sectional areas of the conductors specified herein are identical with the values specified in AS 1125, Conductors in insulated electric cables and flexible cords
17、. Additional conductor sizes referenced are specified in IEC 228, Conductors of insulated cables. The dimensions for non-metallic sheath thicknesses are based on the values recommended in IEC 502. Certain tests and criteria in this Standard are more stringent than those in IEC 840.本文规定导体的标称横截面面积和AS
18、1125绝缘电缆和软线导体的规定值相同。IEC228绝缘电缆导体规定了附加导体的参照尺寸。非金属护套的厚度以IEC502推荐值为准。本标准部分测试和标准比IEC840的同等测试和标准更严格。One type of insulation compound is specified in this Standard, namely insulation comprising cross-linked polyethylene (XLPE).本标准规定了一类绝缘组件，即绝缘用交联聚乙烯（XLPE）。Although the Standard provides tables of insulation
19、 thicknesses and the necessary information to establish precisely the dimensions of the cable protective coverings, no cable dimension tables are provided owing to the variety of cable constructions that could affect such dimensions.尽管本标准提供了绝缘厚度表和必需信息，以精确确定电缆保护套的尺寸，但由于电缆构造的多样性可能会影响电缆尺寸，所以未提供尺寸表。The
20、terms normative and informative have been used in this Standard to define the application of the appendix to which they apply. A normative appendix is an integral part of a Standard, whereas an informative appendix is only for information and guidance.本标准采用术语 “引用标准”和“参考信息”来说明附录的具体用途。“引用标准”附录是标准不可分割的
21、组成部分，而“参考信息”附录仅用作提供信息和指导。Statements expressed in mandatory terms in notes to tables and figures are deemed to be requirements of this Standard.图表附注中的强制性条款视为本标准要求。 Copyright STANDARDS AUSTRALIA/STANDARDS NEW ZEALAND版权声明 澳大利亚标准局/新西兰标准局Users of Standards are reminded that copyright subsists in all Stan
22、dards Australia and Standards New Zealand publications and software. Except where the Copyright Act allows and except where provided for below no publications or software produced by Standards Australia or Standards New Zealand may be reproduced, stored in a retrieval system in any form or transmitt
23、ed by any means without prior permission in writing from Standards Australia or Standards New Zealand. Permission may be conditional on an appropriate royalty payment. Australian requests for permission and information on commercial software royalties should be directed to the head office of Standar
24、ds Australia. New Zealand requests should be directed to Standards New Zealand. 使用标准的用户应注意，澳大利亚标准局和新西兰标准局出版的所有刊物和软件均含有版权。除版权法允许的情况和以下特别规定的情形外，未经澳大利亚标准局和新西兰标准局事先的书面同意，不得对澳大利亚标准局或新西兰标准局出版的任何刊物或开发的软件以任何形式进行复制、储存在检索系统里，或者通过任何方式进行传播。支付适当的使用费后方能获得授权许可。如需申请许可，或需了解有关商用软件的使用费事宜，请分别向澳大利亚标准局或新西兰标准局的总部提出请求。Up t
25、o 10 percent of the technical content pages of a Standard may be copied for use exclusively in-house by purchasers of the Standard without payment of a royalty or advice to Standards Australia or Standards New Zealand.澳大利亚标准局和新西兰标准局允许本标准的购买者复印标准技术内容的10，但仅供内部使用，而无需支付使用费或事先告知。Inclusion of copyright ma
26、terial in computer software programs is also permitted without royalty payment provided such programs are used exclusively in-house by the creators of the programs.如果计算机软件程序由程序的创建者在内部使用，标准局也允许将标准的版权信息包含在该计算机软件程序里，而无需支付使用费。Care should be taken to ensure that material used is from the current edition
27、of the Standard and that it is updated whenever the Standard is amended or revised. The number and date of the Standard should therefore be clearly identified.用户应注意确保其所用的材料是来源于本标准的现行版，并且应随着本标准的修正、修订而更新。本标准的编号和日期应标示清楚。The use of material in print form or in computer software programs to be used comme
28、rcially, with or without payment, or in commercial contracts is subject to the payment of a royalty. This policy may be varied by Standards Australia or Standards New Zealand at any time.无论是否支付了使用费，也不论是否已签订有关协议，凡将此材料（刊印或用于计算机软件程序）用于商业用途的，均应支付使用费。澳大利亚标准局与新西兰标准局有权在任何时候修订这一规定。CONTENTS目录PageSECTION 1 SC
29、OPE AND GENERAL第一章 范围和总则页码1.1SCOPE 范围51.2REFERENCED DOCUMENTS参考文献 51.3DEFINITIONS定义5SECTION 2 CONSTRUCTION第二章 构造2.1GENERAL 概述72.2OPERATING VOLTAGES运行电压 82.3MAXIMUM CONDUCTOR TEMPERATURE导体最高温度 82.4CONDUCTORS 导体82.5CONDUCTOR SCREEN导体屏蔽82.6INSULATION绝缘 92.7EXTRUDED INSULATIONSCREEN挤压绝缘层屏蔽 92.8WATERBLOC
30、KING 阻水102.9MOISTURE BARRIER防潮层102.10 METAL SHEATH金属护套 102.11 METALLIC SCREEN金属屏蔽102.12 BINDERS AND BARRIER TAPES胶粘剂带和屏障带 112.13 NON-METALLIC SHEATH 非金属护套112.14 PROTECTION FROM INSECT ATTACK (OPTIONAL) 防虫（可选）122.15 CABLE IDENTIFICATION电缆识别 122.16 METRE MARKING ON CABLE (OPTIONAL)电缆米数标记（可选） 122.17 PR
31、EPARATION FOR DELIVERY交货准备122.18 MARKING OF DRUMS电缆盘标识 12SECTION 3 TESTS第三章 测试3.1GENERAL 概述133.2CHECK ON INSULATION THICKNESS OF CABLE FOR ELECTRICAL TYPE TEST电气测试电缆的绝缘厚度检查 133.3SELECTION OF SAMPLES样品选择 133.4CABLE CHARACTERISTICS 电缆特性133.5PARTIAL DISCHARGE TEST 局部放电测试183.6HIGH VOLTAGE TEST FOR 30 MI
32、N 30分钟高压测试183.7PARTIAL DISCHARGE TEST AFTER BENDING弯曲后的局部放电测试 183.8MEASUREMENT OF DDF (tan ) AT AMBIENT TEMPERATURE室温下的DDF (tan ) 测量193.9MEASUREMENT OF DDF (tan ) AT OPERATING TEMPERATURE运行温度下的DDF (tan )测量 193.10 PARTIAL DISCHARGE TEST AFTER HEAT CYCLING 热循环后的局部放电测试193.11 IMPULSE TEST FOLLOWED BY A
33、HIGH VOLTAGE TEST脉冲测试，之后是高压测试193.12 RE-QUALIFICATION TESTS再鉴定测试20APPENDICES附录A THE FICTITIOUS CALCULATIfON METHOD FOR THE DETERMINATION OF THE DIMENSIONS OF INSULATION SCREEN AND PROTECTIVE COVERINGS 21 绝缘屏蔽和保护层尺寸测定用虚拟计数法B PURCHASING GUIDELINES购买指南 23C WATER PENETRATION TEST渗水实验 24D RECOMMENDED DIAM
34、ETER OF DRUM BARRfEL AND INSTALLATION BENDING RADIUS FOR CABLES 圆筒电缆盘推荐直径和电缆推荐安装弯曲半径 26E FREQUENCY OF SAMPLE TEST SELECTION AND RETEST PROCEDURE FOR SAMPLE TESTS 样品测试选择频率和样品测试重测步骤 27F ROUNDING OF NUMBERS 数字舍入 28G GUIDE TO THE SELECTION OF ACCESSORIES FOR HV CABLES WITH EXTRUDED INSULATION高压挤压绝缘电缆附件选
35、择指导 29H TESTS AFTER INSTALLATION绝缘后的测试 33STANDARDS AUSTRALIA/STANDARDS NEW ZEALAND澳大利亚标准局/新西兰标准局Australian/New Zealand Standard 澳大利亚/新西兰标准Electric cablesPolymeric insulated电缆聚合绝缘Part 2: For working voltages above 19/33 (36) kV up to and including 76/1 32 (145) kV第二部分：工作电压19/33 (36) kV以上时，电力供应小于等于76/
36、1 32 (145) kVSECTION 1 SCOPE AND GENERAL第一章 范围和总则1.1 SCOPE This Standard specifies requirements for single-core cross-linked polyethylene (XLPE) insulated cables for fixed installations for electricity supply.范围 本标准规定了供电用单芯交联聚乙烯（XLPE）绝缘电缆的固定安装要求。NOTE: Optional requirements for water-blocking, protec
37、tion from insect attack and metre marking on cable are provided in Clauses 2.8, 2.14 and 2.16 respectively.注：第2.8条、2.14条和2.16条分别提供了电缆阻水、防虫和米数标记这些可选要求。1.2 REFERENCED DOCUMENTS The following documents are referred to in this Standard:参考文献 本标准参考了以下文献：AS1018 Partial discharge measurements 局部放电测量1125 Con
38、ductors in insulated electric cables and flexible cords 绝缘电缆和软线导体1660 Test methods for electric cables, cords and conductors (all parts) 电缆、软线和导体的测试方法（所有部分）1931 High voltage testing techniques (all parts) 高压测试技术（所有部分）2893 Electric cablesLead and lead alloy sheathsComposition电缆铅和铅合金护套构成AS/NZS2857 Tim
39、ber drums for insulated electric cables and bare conductors 绝缘电缆和裸导体的木制电缆盘3983 Metal drums for insulated electric cables and bare conductors绝缘电缆和裸导体的金属电缆盘IEC228Conductors of insulated cables 绝缘电缆导体1.3 DEFINITIONS For the purposes of this Standard, the relevant definitions in the referenced Standards
40、 and those below apply. 定义 本标准采用参考标准中的相关定义及下列定义1.3.1 Approximate valuea value which is neither guaranteed nor checked. 近似值未担保且未验证的数值1.3.2 Conductor screena layer or layers of non-metallic semiconductive material applied directly over the conductor. 导体屏蔽直接覆盖在导体上的非金属半导体材料层（单层或多层）1.3.3 Core (of a cable
41、)an assembly comprising a conductor, semiconductive conductor screen, insulation and semiconductive insulation screen. 芯（电缆）由导体、半导电导体屏蔽、绝缘和半导电绝缘屏蔽构成的组件1.3.4 Fictitious values values calculated according to an equation based only on the cross-sectional area of a conductor, the number of cores and spe
42、cified component dimensions, and which ignores conductor shape, degree of compaction of conductors and the possibility of components having dimensions other than specified (see Appendix A). 虚拟值根据方程式计算出的数值，该方程式仅以导体横截面面积、电缆芯数量和规定元件尺寸为基础，且忽略不计导体形状、导体压实度和非规定尺寸元件的可能性（见附录A）。1.3.5 Gross cross-sectional are
43、ain relation to the metallic screen, the product of the calculated cross-sectional area of one screen wire based on its nominal diameter, multiplied by the total number of screen wires in the cable. 横截面总面积对金属屏蔽而言，即计算出的一根屏蔽电线的横截面面积（基于其标称直径）与电缆屏蔽电线总数的乘积。1.3.6 Insulation screena layer or layers of non-
44、metallic semiconductive material applied directly over the insulation. 绝缘屏蔽直接覆盖在绝缘上的非金属半导电材料层（单层或多层）。1.3.7 Length of layin relation to the metallic screen, the axial distance between successive turns of the helix of a screen wire. 绞合节距对金属屏蔽而言，即屏蔽电线螺旋部位连续性匝之间的轴向距离。1.3.8 Maximum conductor temperaturet
45、he maximum temperature at which the conductor of the cable may be operated. It is the temperature resulting from the combined effect of all contributing thermal conditions. 导体最高温度电缆导体可运行的最高温度，是所有起作用热条件下联合作用产生的结果。1.3.9 Moisture barrier a means of preventing radial moisture ingress to the cable core.
46、防潮层防止径向水分浸入电缆芯而采取的手段。1.3.10 Nominal valuea value by which a quantity is designated and which is often used in tables. Usually, in this Standard, nominal values give rise to values to be checked by measurements taking into account specified tolerances. 标称值可指定数量的数值，经常在表中使用。通常情况下，涉及本标准的标称值在考虑规定公差前提下，通过测量进行检查。1.3.11 Non-hygroscopicwhen applied to a material, means that the material after being preconditioned in an oven at 50 5C for 24 1 h and allowed to cool in a desiccator, does not absorb more than 5% by weight
