《MHSA英文USERSMANUAL使用手册.doc》由会员分享，可在线阅读，更多相关《MHSA英文USERSMANUAL使用手册.doc（13页珍藏版）》请在三一办公上搜索。
1、Handheld Ultrasonic Level MeterManual 00000361Contents、company introduction.2、production introduction.2、interface specification.3、technical data.4、data setting.4、cautions.6、connection schema.7、trouble shooting.8、Company introductionWe has being used advanced technology to solve difficult sensing/con
2、trol problems in a broad range of industries. We are specializing in ultrasonic instrument for industry manufacturing and automatic industry, and we have accumulated quite a lot of technology experience for products exploitation and some patents for special products.Our products including ultrasonic
3、 level meter, ultrasonic level sensor, ultrasonic level indicator, ultrasonic flow meter, ultrasonic consistence meter, etc. And the application area of our products include Paper producing, Mining, Reservoir, Petroleum, water treatment, Obstacle detection, collision avoidance etc. our production ar
4、e popular in China, Indian, USA, Indonesia.Under the principle of to be a right man first, we are always concentrating on offering our customers products of perfect quality and heart to heart service. Every customer to us is our friend first, and we will try our best to bring you convenience.、produc
5、tion introductionAdopting excellent experience from home and abroad, this instrument is easy to operation and carry. It employs large scale integrated circuit, mounted rate up to 99% .Owning to that, it is reliable for longer time and brings lowest power consumption. output is RS232.Interface specif
6、icationKey StateFunctionNormalLong press to open/closeMenuBackNormallong press to downloadClick to start/stopNormalEnterMenuPage downInputConfirmNormalOn/off displayMenuEnterInputShift or minusNormalSwitchMenuPage upInputPlus、Technical dataSensing range：mUnusable area： m Output ： Max error：0.3%,1mmC
7、urrent max load impedance：150Sensor frequency：2002000KHz（optional）Work temperature：normal work pressure：normalDisplay ：Display resolution：1mmKey board ：5 sensitive keySensor cable diameter 510mm1.5m（optional）Main processor dimension：20010035(mm)Power：1.5V AA battery or DC 9VNormal consumption：0.5WId
8、le consumption：5mW、Data setting 1Cursor shift from left to right. The sequence of digit input is “09 .”.press confirm to save, power to cancel. When parameter range is narrow, press plus to add and shift to minus. After power off, press“and” at the same time until “Default” shows to restore factory
9、settings.2.Menu Menu Name FunctionCommon HTInstallation heightDecimal Display decimal digitINTENSFilter timesLight Auto-closeOutput F0Start point of output FSEnd point of outputADDSerial port addressBDR.Baud rateSenior COMP *EquationConstant，only 1TEMP CRTemperature correctionDisplay Display correct
10、ionLinear Linear correctionPole*BLBlind area(m)PULPulse intensityFfrequencyGainreceive gain control：0 for autoCollect Time Time setTiming Time timingFix T Fix time (minutes ):0 for manualCL L*CL H*Record0 for Current, 1 for single, 2*Check Check data3. filtering method At some work place, obstacle s
11、hall be appear and reflect sound wave. It will interrupt the sense range seriously. It need to set a filter value to remove. Usage :Press“+”at same time，the distance will be displayed, press “” to shield screen. then press “” to exit. After power off, press“and” at the same time until “Default” show
12、s to restore factory settings.Read this manual carefully before reset data、Cautions 1. Dont put battery anode and cathode reversed. rechargeable battery is available ，better use Nickel hydride batteries .rechargeable power must be standardC and match with our production.2. Insert sensor aligning and
13、 correct. 3. Adjust the end of sensor repeatedly to be vertical to the surface to measured level. The distance between the probe and surface depends on the maximum displacement of the surface to be measured, blind zone of the instrument and range of probe. 4. If the liquid to be measured is sewage o
14、r containing afloat impurities, a wire-fence should be placed under the probe to keep them out of the normal measurement range of the probe. Otherwise correct and stable display can not be obtained.5.Set transmitted pulse intensity properly，avoid abnormal phenomenon.、Connection schema1、 Power and se
15、nsorPower can use 1.5V AA battery or DC 9V. It can charge when using rechargeable battery. Dont use general battery and DC power at the same time. Sensor interface definition illustrated as above diagram、Trouble shootingNOProblem Reason remedy1No display when power onpower is not connected or”“”are
16、reversely.Too low or too high voltagecheck to ensure correct wiring as instructed; check battery powerDisplay values not change with distance Battery power too low, instrument doest work.Pause Check batteryCancel pause3Display values irregular fluctuationtoo deflective installation improper setting
17、of pulse intensity, leading to great residual vibration or diffraction more than 2 instruments on stream, interfering each other too much electromagnetic disturbance adjust the axis of sensor vertical to surface to be measured in general with range of 1-3m, transmit intensity is 2-5. try to eliminat
18、e interference; find out disturbance source and shield from it. 4“OUT” display exceeding measure range too close between surface and sensor. high or low temperature; improper setting of pulse intensity adjust actual range with permitted adjust working conditions as required change transmitting inten
19、sity until stable display5display deviations exceeding 10cmnon vertical installation, leading to multiple reflection installed too close to wall, sonic wave reflected midway check for correct display of temperatureadjust installation positions .for large temperature difference, adjust “TEMP CR” to p
20、roper value6Serial port incommunicablereverse connecting of A and B ports , incorrect “ADD” of serial ports wrong serial port “BDR” reset Para., same with main unitInstrument still not work properly after above step, please contact manufacture or distributorWarranty cardPurchaser TelephoneAddressPos
21、t codeProduct TypeItem No.Delivery date Notes1. According to THREE GUARANTEES,When there are problems with the product under correct operation, it can be refunded, changed and repaired free of charge within one week, three months and one year respectively from the day it was bought.2. For the proble
22、ms caused by improper use, only the cost of material will be charged. 3. The product can not be dismantled or unsealed without manufacturers agreement; otherwise the repair service is not available. 4. The freight out and home in relation to repair will be paid by customer. CertificationProduct: Handheld Ultrasonic Water Depth MeterType：MHItem No：SChong Qing Zhao Zhou Technology Development CO., LTD website：WWW.MHZ99.NETinspector： Delivery date:
