《六朝狮王游戏机英文说明书.doc》由会员分享，可在线阅读，更多相关《六朝狮王游戏机英文说明书.doc（8页珍藏版）》请在三一办公上搜索。
1、Six Lion DynastyConnection using methodAfter communication lines connected in order, it is recommended that one by one from the No. 8 machine to turn on the power, and finally opened the last machines power. The host is in the No. 1machine. Of course, you also can simultaneously open 8 extensions an
2、d host power. If you do not need coin, please pull the line of the coin key on the control stage. Close the coin selectors mouth.Host using method:Normally, as long as the communication line is connected and the power is turned on. The accounts host is in running state when it is normal. The top row
3、 shows the left time for betting during the bet. The following line shows the total profit. The top line shows the left time for running when the light shine and the winning. (That is from playing barcode remaining time, in minutes). Please try playing the barcode before 1000 minutes remaining, in c
4、ase that time runs over when playing (showing time block machine). The following line is also a display of total profits. Normally, as long as you record of the total profits of the following line when you need to shift, you can make the bill clear. As the machine is advanced and reliable, the effic
5、acy is very tight, so in every 2 innings before the shift, there is not on points or under sub so that the host will be able to recode all accounts of the extension accurately. If accounts host and image host does not communicate or communication is not normal, the accounts host has been between 60-
6、50 beating.Reimbursement and audit:First to enter the menu: Go to the menu state, press and hold the function (audit) key down, you can turn on the power directly into the menu. To enter the menu with four choices: audit, reimbursement, Parameters, system. You can press the Select button to move the
7、 arrow. When the arrow pointing to the features you need, press OK, you can enter the function.Here we must note that in reimbursement, before input the bar code, audit, zeroing, which all action can be done after entering the menu, in order to avoid unnecessary trouble, the first is to turn the hos
8、ts power off, and then check all extension are in normal state. If there is a long extension of the alarm, please switch power, making it into the normal state. Last, hold the function key in the host, open accounts hosts the power to enter the menu. The following error operations are frequently enc
9、ountered: 1. Extension power does not turn on while only turn on the host to zero. 2. Extension and accounts host are not connected while open the account host and to zero. 3. Extension has been in false alarms, just open the account host to zero while there is something wrong in extension. Here to
10、remind everyone to be sure to note that our equipment is very strict efficacy. If you do not zero with the host, there will be the 66 on the extension. And the host would show 43 to alarm. So when the extension shows 43 alarm, please re-zero as the above method. If the host LCD has backlight, does n
11、ot show or ghosting, too dark, not clear, please open the hosts back cover, there is a switch on the motherboard to adjust the color, clockwise Lighter counterclockwise darken.Check the host or extension accounts after entering the audit, you can select the host or extension accounts by pressing the
12、 mobile key, you can press OK to enter. After entering the host, the host can check all accounts, the first page above shows the line number, and machine number is displayed below. Press Enter to access the total profits (all extensions add up to the total profits), and press Enter to access the tot
13、al coin (all extension coin + points), press enter to access the total CASHOUT (all extension CASHOUT + points), press Enter go to the previous total profit (the actual earnings when last playing barcode), and press Enter to access the running time (the cumulative running time from last hit barcode)
14、, press Enter to reimbursement times (total playing barcode times), press Enter to access the machine number (in order to facilitate the maintenance and reimbursement, each group machine has a unique machine number), and press Enter to access the total revenue (all points of extensions), and press E
15、nter to access the total expense (all the winning in the extension). The sixth page is alternated, not used here. Press confirm twice back to the total profit page and the whole audit ends. Press Back to exit the host audit. Note: The machine records many things to more convenient for the settlement
16、 of the accounts in this time, if you could not all understand, just recording the total profit is sufficient.Press the move key to select checking extension. You can enter the extension by pressing OK. After entering the extension, input the extension number you want to check, you can check the cor
17、responding extension accounts, including the total profits of the extension, total coin of each extension, total coin return of each extension. Press Back to exit.Enter reimbursement, 00 page shows the total earnings of all the extensions (from the last zero date). 03 page shows the actual profit th
18、is time (accounted from the last playing bar code). 07 page shows the total playing barcode. 08 page shows the number of the machine. 15 page shows the tested code. Finally please enter the bar code, entering the correct bar code can be successfully reimbursement. But after entering reimbursement, a
19、ll extension also enter the reimbursement status; this time does not permit the return exit. All extensions and hosts must shut down before they can exit the reimbursement.The part of system to adjust Boot by pressing the function key and press the movement keys to move the arrow to the parameters,
20、press the Enter key to enter, and then press the confirm to turn the page, press Delete to change:Function code1.play points play card rate（adjust by code making machine）Item930940950960970980990100010102.ratio play card rate （invalid）3.cast cion ratioItem125102050801004.maximum hold down pointsItem
21、1003005009905. hold down points ratioItem125106.power on music（ invalid ）Item7.select multipulItemSmall multipul changeBig multipul changemultipul unchanged 46-5multipul unchanged 40-5multipul unchanged 46-4multipul unchanged 75-4multipul unchanged 70-4multipul unchanged 68-58. hold down points time
22、（input）Item B30354045509.sky ground human playcard rate （ input ）Item Q93094095096097098099010. sky & ground maximum hold down pointsItem9990500045004000350030002500200011. human maximum hold down pointsItem2000100090080070060050040012. select multipul locationItemChangeUnchange13 select procedureIt
23、emMiddle yardSmall yardBig yardWinning allocate principle.As the bet proportion to allocate winning, 10-bit unitsError messageWhen the host machine stops running, the screen displays an error code.Wrong messageIntroductionBug deleteDispose8888Image machine cannot detect code dogdetect code dog1199Ca
24、nnot connect with the accounting machineCheck the accounting machine linking wire09Accounting timeMake accounting book and code08Highest accountsCode turns zeroExtension partExtension setNumber of machine setting: press K3 and boot, press the yellow rabbit (Yellow Panda) to adjust, press the green r
25、abbit (Green Panda) to confirm.MessageErrorCodeIntroductionBug delete31Quit coin motor cannot quit coinTake out the locked coin and then reset the assistant machine30Cast coin machine lock coinTake out the locked coin and then reset the assistant machine99Something wrong in connection with the main
26、machine or start without connection in the middle timeStart the main machine and the assistant machine again. If the problem cannot be solved even, then check the assistant machine board and the RS422 line. If there is something wrong during the wager， the money can be returned， If there is somethin
27、g wrong during opening the prize，the money should be remained，when the connection is build，.the wager will be dealed with according to the wager which unconnection happens.Other errorsMain machine displays nothing1.main machine and the monitor are powered offCheck the power or insert the power wire
28、again.2. VGA wire is loosen or damagedinsert the VGA wire again or change it3.something wrong with divide machineCheck the divide machine light and check VGA wire which connect the main machine and the divide machine to make sure it is insert right。Main machine cannot startThe machine reports that a
29、 file is wrong or losed during the move1.repair according to the monitor shows2.select the last time correct deploy ”or start GHOST system againMain machine silent1. voice box power is offSwitch on the voice box power2.signal line loosenCheck the signal line and insert it again3.voice box is destroy
30、edreplaceCannot input bar code1.digit keyboard isnot startPress Numlock to make it work（light on）*2.keyboard is destroyedPut the keyboard on other machine to check if it should be changed3.input wrong bar codeCheck and input againImage cannot move，accounts machineKeep repeat in 10 secondsCheck the c
31、onnection line with the account machine，when the connection is build, start the machine again.Assistant machine cannot start1.switch line isnot connectConnect again2. 24v electric tension cannot outputCheck 24v power source joint and the power source3 Assistant machine board is destroyedPut it on ot
32、her machine to check if it should be changedThe construction of hostShutdown requirements:Shutdown mode: 1. If the keyboard has power key, turn power off. 2. No power key on the keyboard, you need to use the ESC key to exit the game screen, then the micro-standard key + U + U to turn off the host. 3
33、 directly press the power button to shut downNote: can not be used directly off the external power supply to shut down in case that the host is damaged.Coding instructionPress the audit key on the host, and start the machine. Move the arrow to reimbursement, press OK!Please input the 0, 3, 7,8,15 ta
34、bles of the host to the transcoder. Press # to confirm.The transcoder displays: to keep” move the movement keys to select the pumping” or water, press # to confirm.Then the transcoder shows to keep. Press * and choose 930-1010, press # to confirmInput the generated password to the host, ok!Number th
35、e machine numbers as follows:First turn off and press the K3 key on the extension board (the key is the first small button next to the power strip); then turn on the power and a row of the digital tube under the control platform will display 00000000.Then press the continued bet key on the control s
36、tage (the number will show on the record board or “88” on the online running light board), keep pressing until the digital display to 7; press the coin return button on the control platform. Then no. 1 to no. 16 machine will show, you can number the machine as you want. Finally click the continued bet key to confirm and turn on or turn off the machine.
