《WeldFit Pushin Fittings.ppt》由会员分享，可在线阅读，更多相关《WeldFit Pushin Fittings.ppt（30页珍藏版）》请在三一办公上搜索。
1、WeldFit Push-in Fittings,WeldFit Push-in Fittings,For use with WeldTube to protect against damage from weld spatter.Easy tube insertion and removalTube support for retention under high loadsRecessed collet to prevent exposure of inner tube under side loadsCorrosion resistant nickel platedSizes G1/8,
2、G1/4,G3/8,G1/2Inner tube 6,8,10,12mm o/dFor compressed air or water,WeldFit component parts,Recessed colletMultiple teethO RingTube supportBodySealing washerTemperature range-300C to 700CMaterialsCorrosion resistant nickel plated brass componentsNitrile O RingPolyamide washer,Tube preparation,WeldFi
3、t push-in fittings,Tube preparation,Using a standard tube cutter,cut the complete tube end square at one of the markers.Ensure that the tube end is clean and free from surface damage,Tube preparation,To prevent damage to the inner tube.Use the special stripping tool to cut the outer cover at the nex
4、t marker,Tube preparation,Push open the tube gripInsert the cut to length tube and line up the next marker with the bladeClose the tube grip and rotate the stripper around the circumference of the tube,Tube preparation,Push open the tube gripInsert the cut to length tube and line up the next marker
5、with the bladeClose the tube grip and rotate the stripper around the circumference of the tube,Tube preparation,Push open the tube gripInsert the cut to length tube and line up the next marker with the bladeClose the tube grip and rotate the stripper around the circumference of the tube,Tube prepara
6、tion,Next push the blade twist button,this turns the blade 900Hold the button down and pull the stripper sideways to score the tube to the endPeal off the outer covering,Tube preparation,Next push the blade twist button,this turns the blade 900Hold the button down and pull the stripper sideways to s
7、core the tube to the endPeal off the outer covering,Tube preparation,Next push the blade twist button,this turns the blade 900Hold the button down and pull the stripper sideways to score the tube to the endPeal off the outer covering,Tube preparation,Next push the blade twist button,this turns the b
8、lade 900Hold the button down and pull the stripper sideways to score the tube to the endPeal off the outer covering,Tube and fitting assembly,WeldFit push-in fittings,Tube assembly,Push the tube firmly into the collet over the tube support,through the O ring and down to the tube stop.Pull back on th
9、e tube to reinforce the collet teeth gripping actionThe pressure can then be applied,Tube assembly,Push the tube firmly into the collet over the tube support,through the O ring and down to the tube stop.Pull back on the tube to reinforce the collet teeth gripping actionThe pressure can then be appli
10、ed,Tube assembly,Push the tube firmly into the collet over the tube support,through the O ring and down to the tube stop.Pull back on the tube to reinforce the collet teeth gripping actionThe pressure can then be applied,Tube assembly,Push the tube firmly into the collet over the tube support,throug
11、h the O ring and down to the tube stop.Pull back on the tube to reinforce the collet teeth gripping actionThe pressure can then be applied,Tube assembly,Push the tube firmly into the collet over the tube support,through the O ring and down to the tube stop.Pull back on the tube to reinforce the coll
12、et teeth gripping actionThe pressure can then be applied,Tube removal,WeldFit push-in fittings,Tube removal,Turn off and exhaust the pressureTo remove the tube,push the collet in firmly and hold it there.Pull the tube out and release the collet,Tube removal,Turn off and exhaust the pressureTo remove
13、 the tube,push the collet in firmly and hold it there.Pull the tube out and release the collet,Tube removal,Turn off and exhaust the pressureTo remove the tube,push the collet in firmly and hold it there.Pull the tube out and release the collet,Tube removal,Turn off and exhaust the pressureTo remove
14、 the tube,push the collet in firmly and hold it there.Pull the tube out and release the collet,The range,WeldFit push-in fittings,WeldFit Push-in Fittings,Included in the range:Straight adaptorsStraight connectorsElbow connectorsTee connectors900 Swivel adaptors450 Swivel adaptorsBanjo assembly range,WeldTube range,Tube range,Four tube sizes each with outer tube colours in a choice of black,blue,green or red.Inner tube o/d 6,8,10 and 12 mm(4,6,7,9 mm id)Outer tube o/d 8,10,12.5,14.5 mm,Tube range,Minimum recommended bend radius40,50,65 and 75 mm,End,
