机械设计及其自动化专业毕业设计论文外文翻译.doc

上传人:sccc 文档编号:4860431 上传时间:2023-05-20 格式:DOC 页数:24 大小:1.05MB
返回 下载 相关 举报
机械设计及其自动化专业毕业设计论文外文翻译.doc_第1页
第1页 / 共24页
机械设计及其自动化专业毕业设计论文外文翻译.doc_第2页
第2页 / 共24页
机械设计及其自动化专业毕业设计论文外文翻译.doc_第3页
第3页 / 共24页
机械设计及其自动化专业毕业设计论文外文翻译.doc_第4页
第4页 / 共24页
机械设计及其自动化专业毕业设计论文外文翻译.doc_第5页
第5页 / 共24页
点击查看更多>>
资源描述

《机械设计及其自动化专业毕业设计论文外文翻译.doc》由会员分享,可在线阅读,更多相关《机械设计及其自动化专业毕业设计论文外文翻译.doc(24页珍藏版)》请在三一办公上搜索。

1、南湖学院毕业设计(论文)外文翻译资料作 者届 别2011系 别机械与电子工程系专 业机械设计及其自动化指导老师职 称副教授完成时间2011年5月18日 23Automated surface finishing of plastic injection mold steel with spherical grinding and ball burnishing processesAbstractThis study investigates the possibilities of automated spherical grinding and ball burnishing surface

2、 finishing processes in a freeform surface plastic injection mold steel PDS5 on a CNC machining center. The design and manufacture of a grinding tool holder has been accomplished in this study. The optimal surface grinding parameters were determined using Taguchis orthogonal array method for plastic

3、 injection molding steel PDS5 on a machining center. The optimal surface grinding parameters for the plastic injection mold steel PDS5 were the combination of an abrasive material of PA Al2O3, a grinding speed of 18 000 rpm, a grinding depth of 20 m, and a feed of 50 mm/min. The surface roughness Ra

4、 of the specimen can be improved from about 1.60 m to 0.35 m by using the optimal parameters for surface grinding. Surface roughness Ra can be further improved from about 0.343 m to 0.06 m by using the ball burnishing process with the optimal burnishing parameters. Applying the optimal surface grind

5、ing and burnishing parameters sequentially to a fine-milled freeform surface mold insert, the surface roughness Ra of freeform surface region on the tested part can be improved from about 2.15 m to 0.07 m.Keywords Automated surface finishing; Ball burnishing process; Grinding process; Surface roughn

6、ess; Taguchis method1 IntroductionPlastics are important engineering materials due to their specific characteristics, such as corrosion resistance, resistance to chemicals, low density, and ease of manufacture, and have increasingly replaced metallic components in industrial applications. Injection

7、molding is one of the important forming processes for plastic products. The surface finish quality of the plastic injection mold is an essential requirement due to its direct effects on the appearance of the plastic product. Finishing processes such as grinding, polishing and lapping are commonly us

8、ed to improve the surface finish.The mounted grinding tools (wheels) have been widely used in conventional mold and die finishing industries. The geometric model of mounted grinding tools for Fig.1. Schematic diagram of the spherical grinding processautomated surface finishing processes was introduc

9、ed in. A finishing process mode of spherical grinding tools for automated surface finishing systems was developed in. Grinding speed, depth of cut, feed rate, and wheel properties such as abrasive material and abrasive grain size, are the dominant parameters for the spherical grinding process, as sh

10、own in Fig. 1. The optimal spherical grinding parameters for the injection mold steel have not yet been investigated based in the literature.In recent years, some research has been carried out in determining the optimal parameters of the ball burnishing process (Fig. 2). For instance, it has been fo

11、und that plastic deformation on the workpiece surface can be reduced by using a tungsten carbide ball or a roller, thus improving the surface roughness, surface hardness, and fatigue resistance. The burnishing process is accomplished by machining centers and lathes. The main burnishing parameters ha

12、ving significant effects on the surface roughness are ball or roller material, burnishing force, feed rate, burnishing speed, lubrication, and number of burnishing passes, among others. The optimal surface burnishing parameters for the plastic injection mold steel PDS5 were a combination of grease l

13、ubricant, the tungsten carbide ball, a burnishing speed of 200 mm/min, a burnishing force of 300 N, and a feed of 40 m. The depth of penetration of the burnished surface using the optimal ball burnishing parameters was about 2.5 microns. The improvement of the surface roughness through burnishing pr

14、ocess generally ranged between 40% and 90%.Fig. 2. Schematic diagram of the ball-burnishing processThe aim of this study was to develop spherical grinding and ball burnishing surface finish processes of a freeform surface plastic injection mold on a machining center. The flowchart of automated surfa

15、ce finish using spherical grinding and ball burnishing processes is shown in Fig. 3. We began by designing and manufacturing the spherical grinding tool and its alignment device for use on a machining center. The optimal surface spherical grinding parameters were determined by utilizing a Taguchis o

16、rthogonal array method. Four factors and three corresponding levels were then chosen for the Taguchis L18 matrix experiment. The optimal mounted spherical grinding parameters for surface grinding were then applied to the surface finish of a freeform surface carrier. To improve the surface roughness,

17、 the ground surface was further burnished, using the optimal ball burnishing parameters.Fig. 3. Flow chart of automated surface finish using spherical grinding and ball burnishing processes2 Design of the spherical grinding tool and its alignment deviceTo carry out the possible spherical grinding pr

18、ocess of a freeform surface, the center of the ball grinder should coincide with the z-axis of the machining center. The mounted spherical grinding tool and its adjustment device was designed, as shown in Fig. 4. The electric grinder was mounted in a tool holder with two adjustable pivot screws. The

19、 center of the grinder ball was well aligned with the help of the conic groove of the alignment components. Having aligned the grinder ball, two adjustable pivot screws were tightened; after which, the alignment components could be removed. The deviation between the center coordinates of the ball gr

20、inder and that of the shank was about 5 m, which was measured by a CNC coordinate measuring machine. The force induced by the vibration of the machine bed is absorbed by a helical spring. The manufactured spherical grinding tool and ball-burnishing tool were mounted, as shown in Fig. 5. The spindle

21、was locked for both the spherical grinding process and the ball burnishing process by a spindle-locking mechanism.Fig.4. Schematic illustration of the spherical grinding tool and its adjustment deviceFig.5. (a) Photo of the spherical grinding tool (b) Photo of the ball burnishing tool3 Planning of t

22、he matrix experiment3.1 Configuration of Taguchis orthogonal arrayThe effects of several parameters can be determined efficiently by conducting matrix experiments using Taguchis orthogonal array. To match the aforementioned spherical grinding parameters, the abrasive material of the grinder ball (wi

23、th the diameter of 10 mm), the feed rate, the depth of grinding, and the revolution of the electric grinder were selected as the four experimental factors (parameters) and designated as factor A to D (see Table 1) in this research. Three levels (settings) for each factor were configured to cover the

24、 range of interest, and were identified by the digits 1, 2, and 3. Three types of abrasive materials, namely silicon carbide (SiC), white aluminum oxide (Al2O3, WA), and pink aluminum oxide (Al2O3, PA), were selected and studied. Three numerical values of each factor were determined based on the pre

25、-study results. The L18 orthogonal array was selected to conduct the matrix experiment for four 3-level factors of the spherical grinding process.Table1 The experimental factors and their levels3.2 Definition of the data analysisEngineering design problems can be divided into smaller-the better type

26、s, nominal-the-best types, larger-the-better types, signed-target types, among others 8. The signal-to-noise (S/N) ratio is used as the objective function for optimizing a product or process design. The surface roughness value of the ground surface via an adequate combination of grinding parameters

27、should be smaller than that of the original surface. Consequently, the spherical grinding process is an example of a smaller-the-better type problem. The S/N ratio, , is defined by the following equation: =10 log10(mean square quality characteristic) =10 log10where:yi : observations of the quality c

28、haracteristic under different noise conditions n: number of experimentAfter the S/N ratio from the experimental data of each L18 orthogonal array is calculated, the main effect of each factor was determined by using an analysis of variance (ANOVA) technique and an F-ratio test. The optimization stra

29、tegy of the smaller-the better problem is to maximize , as defined by Eq. 1. Levels that maximize will be selected for the factors that have a significant effect on . The optimal conditions for spherical grinding can then be determined.4 Experimental work and resultsThe material used in this study w

30、as PDS5 tool steel (equivalent to AISI P20), which is commonly used for the molds of large plastic injection products in the field of automobile components and domestic appliances. The hardness of this material is about HRC33 (HS46). One specific advantage of this material is that after machining, t

31、he mold can be directly used for further finishing processes without heat treatment due to its special pre-treatment. The specimens were designed and manufactured so that they could be mounted on a dynamometer to measure the reaction force. The PDS5 specimen was roughly machined and then mounted on

32、the dynamometer to carry out the fine milling on a three-axis machining center made by Yang-Iron Company (type MV-3A), equipped with a FUNUC Company NC-controller (type 0M). The pre-machined surface roughness was measured, using Hommelwerke T4000 equipment, to be about 1.6 m. Figure 6 shows the expe

33、rimental set-up of the spherical grinding process. A MP10 touch-trigger probe made by the Renishaw Company was also integrated with the machining center tool magazine to measure and determine the coordinated origin of the specimen to be ground. The NC codes needed for the ball-burnishing path were g

34、enerated by PowerMILL CAM software. These codes can be transmitted to the CNC controller of the machining center via RS232 serial interface.Table 2 summarizes the measured ground surface roughness alue Ra and the calculated S/N ratio of each L18 orthogonal array sing Eq. 1, after having executed the

35、 18 matrix experiments. The average S/N ratio for each level of the four actors is shown graphically in Fig. 7.Table2. Ground surface roughness of PDS5 specimenExp.Inner array (control factors)Measured surface roughness value (Ra)ResponsenoABCDS/N(dB)Mean111110.350.350.359.1190.350212220.370.360.388

36、.6340.370313330.410.440.407.5970.417421230.630.650.643.8760.640522310.730.770.782.3800.760623120.450.420.397.5300.420731320.340.310.329.8010.323832130.270.250.2811.4710.267933210.320.320.329.8970.3201011220.350.390.408.3900.3801112330.410.500.436.9680.4471213110.400.390.427.8830.4031321130.330.340.3

37、19.7120.3271422210.480.500.476.3120.4831523320.570.610.534.8680.5701631310.590.550.545.0300.5601732120.360.360.358.9540.357Fig.7. Plots of control factor effectsThe goal in the spherical grinding process is to minimize the surface roughness value of the ground specimen by determining the optimal lev

38、el of each factor. Since log is a monotone decreasing function, we should maximize the S/N ratio. Consequently, we can determine the optimal level for each factor as being the level that has the highest value of . Therefore, based on the matrix experiment, the optimal abrasive material was pink alum

39、inum oxide; the optimal feed was 50 mm/min; the optimal depth of grinding was 20 m; and the optimal revolution was 18 000 rpm, as shown in Table 3.Table 3 optimized combination spherical grinding parameters FactorLevelAbrsive PAfeed50mm/minDepth of griindingRevolution18000rpmThe optimal parameters f

40、or surface spherical grinding obtained from the Taguchis matrix experiments were applied to the surface finish of the freeform surface mold insert to evaluate the surface roughness improvement. A perfume bottle was selected as the tested carrier. The CNC machining of the mold insert for the tested o

41、bject was simulated with Power MILL CAM software. After fine milling, the mold insert was further ground with the optimal spherical grinding parameters obtained from the Taguchis matrix experiment. Shortly afterwards, the ground surface was burnished with the optimal ball burnishing parameters to fu

42、rther improve the surface roughness of the tested object (see Fig. 8). The surface roughness of the mold insert was measured with Hommelwerke T4000 equipment. The average surface roughness value Ra on a fine-milled surface of the mold insert was 2.15 m on average; that on the ground surface was 0.45

43、 m on average; and that on burnished surface was 0.07 m on average. The surface roughness improvement of the tested object on ground surface was about (2.150.45)/2.15 = 79.1%, and that on the burnished surface was about (2.150.07)/2.15 = 96.7%.Fig.8. Fine-milled, ground and burnished mold insert of

44、a perfume bottle5 ConclusionIn this work, the optimal parameters of automated spherical grinding and ball-burnishing surface finishing processes in a freeform surface plastic injection mold were developed successfully on a machining center. The mounted spherical grinding tool (and its alignment comp

45、onents) was designed and manufactured. The optimal spherical grinding parameters for surface grinding were determined by conducting a Taguchi L18 matrix experiments. The optimal spherical grinding parameters for the plastic injection mold steel PDS5 were the combination of the abrasive material of p

46、ink aluminum oxide (Al2O3, PA), a feed of 50 mm/min, a depth of grinding 20 m, and a revolution of 18 000 rpm. The surface roughness Ra of the specimen can be improved from about 1.6 m to 0.35 m by using the optimal spherical grinding conditions for surface grinding. By applying the optimal surface

47、grinding and burnishing parameters to the surface finish of the freeform surface mold insert, the surface roughness improvements were measured to be ground surface was about 79.1% in terms of ground surfaces, and about 96.7% in terms of burnished surfaces. 基于注塑模具钢研磨和抛光工序的自动化表面处理摘要本文研究了注塑模具钢自动研磨与球面抛光加工工序的可能性,这种注塑模具钢PDS5的塑性曲面是在数控加工中心完成的。这项研究已经完成了磨削刀架的设计与制造。 最佳表面研磨参数是在钢铁PDS5 的加工中心测定的。对于PDS5注塑模具钢的最佳球面研磨参数是以下一系列的组合:研磨材料的磨料为粉红氧化铝,进给量500毫米/分钟,磨削深度20微米,磨削转速为18000RPM。用优化的参数进行表面研磨,表面粗糙度Ra值可

展开阅读全文
相关资源
猜你喜欢
相关搜索
资源标签

当前位置:首页 > 建筑/施工/环境 > 农业报告


备案号:宁ICP备20000045号-2

经营许可证:宁B2-20210002

宁公网安备 64010402000987号