《【英国标准word原稿】BS EN 13352 Office furniture — Office work chair Part 2 Safety requirements.doc》由会员分享，可在线阅读，更多相关《【英国标准word原稿】BS EN 13352 Office furniture — Office work chair Part 2 Safety requirements.doc（15页珍藏版）》请在三一办公上搜索。
1、豆丁网：BRITISH STANDARDBS EN1335-2:2009第 3 页 共 15 页豆丁网：Office furniture Office work chairPart 2: Safety requirementsICS 13.180; 97.140NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 1335-2:2009National forewordThis British Standard is the UK implementation of EN 1335-2:2009.
2、 It supersedes BS EN 1335-2:2000 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee FW/0/3, Office.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necess
3、ary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April2009 BSI 2009ISBN 978 0 5
4、80 58648 4Amendments/corrigenda issued since publicationDate CommentsBS EN 1335-2:2009EUROPEAN STANDARD NORME EUROPENNEEUROPISCHE NORMEN 1335-2April 2009ICS 97.140Supersedes EN 1335-2:2000English VersionOffice furniture - Office work chair - Part 2: Safety requirementsMobilier de bureau - Siges de t
5、ravail de bureau - Partie 2: Exigences de scuritBrombel - Bro-Arbeitsstuhl - Teil 2: SicherheitsanforderungenThis European Standard was approved by CEN on 28 February 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Europea
6、n Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English,
7、French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cypr
8、us, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATION C O
9、M I T EUR OP EN DE NOR M AL I S ATI ON EUR OP I S C HES KOM I TEE F R NOR M UNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members.Ref. No. EN 1335-2:2009: EContentsPageForeword.31Scope .42N
10、ormative references .43Terms and definitions .44Safety requirements .44.1General design requirements .44.1.1Corners and edges, trapping, pinching and shearing .44.1.2Adjusting devices .54.1.3Connections .54.1.4Avoidance of soiling.54.2Test sequence .54.3Stability during use.64.4Rolling resistance of
11、 the unloaded chair .64.5Strength and durability .65Information for use .7Annex A (normative) Loads, masses and cycles for safety tests .89BS EN 1335-2:2009EN 1335-2:2009 (E)ForewordThis document (EN 1335-2:2009) has been prepared by Technical Committee CEN/TC 207 “Furniture”, the secretariat of whi
12、ch is held by UNI.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2009, and conflicting national standards shall be withdrawn at the latest by October 2009.Attention is drawn to the possib
13、ility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights.This document supersedes EN 1335-2:2000. This series consist of following parts:EN 1335-1, Office furniture Office work
14、 chair Part 1: Dimensions Determination of dimensions; EN 1335-2, Office furniture Office work chair Part 2: Safety requirements;EN 1335-3, Office furniture Office work chair Part 3: Test methods. The main changes with respect to the previous edition are listed below: a)castor durability (former 6.2
15、) has been defined as functional test;b)foot rest stability and foot rest static load have been defined as safety test.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, B
16、ulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.1ScopeThis part of EN 133
17、5 specifies the mechanical safety requirements for office work chairs.The requirements are based upon use for 8 h a day by persons weighing up to 110 kg. For more severe conditions of use, increased requirements will be necessary.Annex A (normative) includes loads, masses and cycles for safety tests
18、.Additional loads, masses and cycles for functional tests can be found in EN 1335-3:2009, Annex C.2Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest e
19、dition of the referenced document (including any amendments) applies.EN 1335-1:2000, Office furniture Office work chair Part 1: Dimensions Determination of dimensionsEN 1335-3:2009, Office furniture Office work chair Part 3: Test methodsEN 12529:1998, Castors and wheels Castors for furniture Castors
20、 for swivel chairs Requirements3Terms and definitionsFor the purposes of this document, the following terms and definitions apply.3.1 castorassembly comprising a housing, one or more wheels, an axle and, if required, accessoriesEN 12529:19984Safety requirements4.1General design requirements4.1.1Corn
21、ers and edges, trapping, pinching and shearingThe chair shall be so designed as to minimise the risk of injury to the user.All parts of the chair with which the user comes into contact during intended use, shall be so designed that physical injury and damage to property are avoided.These requirement
22、s are met when:a)the safety distance of accessible movable parts is either 8 mm or 25 mm in any position during movement;b)accessible corners are rounded with minimum 2 mm radius;c)the edges of the seat, back rest and arm rests which are in contact with the user when sitting in the chair are rounded
23、 with minimum 2 mm radius;d)the edges of handles are rounded with minimum 2 mm radius in the direction of the force applied;e)all other edges are free from burrs and rounded or chamfered;f)the ends of accessible hollow components are closed or capped.4.1.2Adjusting devicesMovable and adjustable part
24、s shall be designed so that injuries and inadvertent operation are avoided. It shall be possible to operate the adjusting devices from sitting position in the chair.4.1.3ConnectionsIt shall not be possible for any load bearing part of the chair to come loose unintentionally.4.1.4Avoidance of soiling
25、All parts which are lubricated to assist sliding (greasing, lubricating, etc.) shall be designed to protect users from lubricant stains when in normal use.4.2Test sequenceThe same chair shall be tested in the following sequence:a)stability tests (optional);b)rolling resistance test (optional);c)seat
26、 and back rest tests; d)foot rest static load test; e)arm rests durability test;f)arm rest downward static load test - central (see Table A.2, Footnote a);g)stability tests;h)arm rest downward static load test - central (see Table A.2, Footnote b);i)rolling resistance test.4.3Stability during useThe
27、 chair shall not overbalance under the following conditions:a)by pressing down on the front edge of the seat surface in the most adverse position;b)by leaning out over the arm rests; c)by leaning against the back rest; d)by sitting on the front edge.Requirement a) is fulfilled if the chair does not
28、overbalance when tested according to 7.1.1 of EN 1335-3:2009 with the forces and numbers of cycles according to Table A.1 of this standard.Requirements b) and d) are fulfilled if the chair does not overbalance when tested according to 7.1.2, 7.1.3,7.1.4 and 7.1.5 of EN 1335-3:2009 with the forces an
29、d numbers of cycles according to Table A.1 of this standard.Requirement c) is fulfilled if the chair does not overbalance when tested according to 7.1.6 or 7.1.7 ofEN 1335-3:2009 with the forces and numbers of cycles according to Table A.1 of this standard.4.4Rolling resistance of the unloaded chair
30、The unloaded chair shall not roll unintentionally. This requirement is met when:a)the castors are of identical construction;b)the rolling resistance is 12 N when tested according to EN 1335-3:2009, 7.4.4.5Strength and durabilityThe chair shall be constructed to ensure that it does not create a risk
31、of injury to the user of the chair under the following conditions:a)sitting on the seat, both centrally and off-centre;b)moving forward, backwards, and sideways while sitting in the chair;c)leaning over the arm rests;d)pressing down on the arm rests while getting up from the chair.These requirements
32、 are fulfilled when after the tests specified in 7.2.1, 7.2.2, 7.2.6, 7.3.1 and 7.3.2 ofEN 1335-3:2009 with the forces and numbers of cycles according to Table A.2 of this standard:e)there are no fractures of any member, joint or component, and f)there is no loosening of joints intended to be rigid,
33、 andg)no major structural element is significantly deformed and the chair fulfils its functions after removal of the test loadsand when:h)after the test in 7.2.3 of EN 1335-3:2009 with the forces and numbers of cycles according to Table A.2 of this standard, the arm rests show no fracture.5Informati
34、on for useEach chair shall be accompanied by information for use in the language of the country in which it will be delivered to the end user. It shall contain at least the following details:a)information regarding the intended use;b)information regarding possible adjustments and chair type (see EN
35、1335-1:2000);c)instruction for operating the adjusting mechanisms;d)instruction for the care and maintenance of the chair;e)information regarding all adjustments;f)information for chairs with seat height adjustments with energy accumulators that only trained personnel may replace or repair seat heig
36、ht adjustment components with energy accumulators;g)information on the choice of castors in relation to the floor surface.Annex A(normative)Loads, masses and cycles for safety testsTable A.1 Loads, masses and cycles for stability testsClauses given inEN 1335-3:2009TestLoadsCycle7.1.1Front edge overt
37、urningM127 kg17.1.2Forward overturningF1F2600 N20 N17.1.3F1Forward overturning for chairs with foot restsF21 100 N20 N17.1.4F1Sideways overturning for chairs without arm restsF2600 N20 N17.1.5F1Sideways overturning for chairs with arm restsF2F3250 N350 N20 N17.1.6F1Rearwards overturning of chairs wi
38、thout back rest inclinationF2600 N192 N17.1.7Rearwards overturning of chairs with back rest inclinationNumber of discs:131Table A.2 Loads and cycles for strength and durability testsClauses given inEN 1335-3:2009TestLoadsCycles7.2.1Seat front edge static load testF11 600 N107.2.2F1Combined seat and back static load testF21 600 N560 N107.2.6Foot rest static load testF1 300 N107.3.1Seat and back durabilityStep 1 Loading Point AF1 500 N120 000Step 2 Loading Point CFLoading Point BF1 200 N320 N80 000Step 3 Loading Point JFLoading Point EF1 200 N320 N
