《1043低速转接套齿样件检验报告.doc》由会员分享，可在线阅读，更多相关《1043低速转接套齿样件检验报告.doc（3页珍藏版）》请在三一办公上搜索。
1、DABG-ZB-91注：粗线框内由东安动力填写，本报告一式四联。区 分样品种类送检日期： 年 月 日判定日期： 年 月 日样件检验报告新开发件半 成 品设计变更件成 品工程变更件改进产品关键重要一般 更改单日期： ；更改单编号： ；图面版本号：供方：重庆市江汇机械有限责任公司 (第 1 次送样)样品数量：5件 试生产产量：机型：DABS10-4 件号：BS10-4-1701043 件名：低速转接套齿 样品重量： 217 g报告内容：尺寸检验 材质报告 性能试验 耐久试验 统计资料 外观件报告 其它送审理由：新开发件样件标识方法及编号使用材料核准审核填表粉末冶金SMF5040-JIS Z 255
2、0-1983东安综合判定核准审核填表合格判定内容：条件合格不合格简图及说明：按规范要求项目所作成之材料、成分、物性、性能试验等报告难以记载本报告以任意格式附纸于后。粗线框内由DA填写。检 验 报 告（续页）DABG-ZB-91注：粗线框内由东安动力填写机型：DABS10-4 件号：BS10-4-1701043 名称：低速转接套齿序号检验项目规 格12345678910判定1距离25.525.4225.3625.3425.4825.4625.4025.3825.4225.4225.3425.4020.002042宽度5.6（三处）5.625.585.545.605.625.545.585.565
3、.565.625.5820.000923油槽深度1.51.501.521.481.501.521.521.481.481.521.501.5020.000284油槽圆弧R55.025.024.984.985.005.005.025.024.985.025.0040.00035跳动0.10.090.090.080.090.090.080.080.090.090.090.0870.000026厚度160.0516.0115.9715.9716.0316.0116.0115.9715.9815.9816.0115.9940.000447厚度40.23.93.93.94.14.13.94.04.04.
4、13.93.980.00768外径44（两端）43.9643.9644.0644.0644.0243.9843.9844.0244.0644.0244.0120.001469内径56.356.4256.5456.4256.3856.3856.4256.4856.3856.5256.5656.450.0043410外花键大径63.663.5463.5863.5463.5463.5463.5863.5863.5463.5463.5863.5560.0003811跳动0.10.090.090.080.090.090.080.080.080.090.090.0860.0000212厚度88.027.9
5、67.968.008.008.028.027.967.968.027.9920.0007413深度43.983.984.063.984.004.003.983.984.024.0240.0006414总厚度240.2523.8624.1623.8624.1624.1024.1023.9624.1024.1623.9624.0420.0131615识别标记定位尺寸17.517.417.517.517.517.417.417.517.517.417.417.450.002516倒角深0.30.30.30.30.290.300.300.290.290.290.300.2960.0000217倒角宽0
6、.20.190.190.200.210.190.200.210.200.190.210.1990.0000718外花键小径59.259.1859.1859.1659.1859.1659.1259.1259.1459.1659.1859.1580.0005219内花键大径3333.02532.99533.01533.01532.9932.99533.02533.0332.9933.04533.01250.00033检 验 报 告（续页）DABG-ZB-91：粗线框内由东安动力填写机型：DABS10-4 件号：BS10-4-1701043 名称：低速转接套齿序号检验项目规 格12345678910
7、判定20内花键小径3131.0431.0431.0431.0231.0631.0631.0631.0231.0431.0231.040.0002421外花键公法线长度28.528.4628.4428.4428.4628.4628.4828.4628.4628.4428.4428.4540.0001622内花键跨棒距29.02829.13529.0429.13529.15529.1629.05529.0629.13529.14529.1529.1170.0019223外花键综合公差0.050.040.040.040.030.040.040.040.030.030.030.0360.0000224内花键综合公差0.050.030.030.040.040.030.030.040.040.040.030.0350.0000325材料组成FeC0.30.8Cu13Ni 28其它126材料密度6.8g/cm27压溃力6860N延伸率1夏氏冲击值9.8N.m/c28调质处理硬度HRA6529磁流探伤无裂纹
