《【AS澳大利亚标准】AS 4830 Determination of the extinction propensity of cigarettes.doc》由会员分享，可在线阅读，更多相关《【AS澳大利亚标准】AS 4830 Determination of the extinction propensity of cigarettes.doc（22页珍藏版）》请在三一办公上搜索。
1、AS 48302007Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 17 Mar 2007AS 48302007Australian StandardDetermination of the extinction propensity of cigarettesThe Standard is downloaded from Standard SharingThis Australian Standard was prepared by Committee CS-102, Reduced Fire RiskCigarettes. It was appr
2、oved on behalf of the Council of Standards Australia on19 February 2007.This Standard was published on 5 March 2007.The following are represented on Committee CS-102:Australasian Fire Authorities CouncilAustralian Consumers AssociationCSIRO & Infrastructure TechnologyFire Protection Association Aust
3、raliaFurntechInsurance Council of AustraliaNew South Wales Department of HealthTobacco Product Manufacturing InterestsThe University of SydneyThis Standard was issued in draft form for comment as DR 06483.Standards Australia wishes to acknowledge the participation of the expert individuals that cont
4、ributed to the development of this Standard through their representation on the Committee and through public comment period.Keeping Standards up-to-dateAccessed by UNIVERSITY OF SOUTH AUSTRALIA on 17 Mar 2007Australian Standards are living documents that reflect progress in science, technology and s
5、ystems. To maintain their currency, all Standards are periodically reviewed, and new editions are published. Between editions, amendments may be issued.Standards may also be withdrawn. It is important that readers assure themselves they are using a current Standard, which should include any amendmen
6、ts that may have been published since the Standard was published.Detailed information about Australian Standards, drafts, amendments and new projects can be found by visiting www.standards.org.auStandards Australia welcomes suggestions for improvements, and encourages readers to notify us immediatel
7、y of any apparent inaccuracies or ambiguities. Contact us via email at mailstandards.org.au, or write to Standards Australia, GPO Box 476, Sydney, NSW 2001.AS 48302007Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 17 Mar 2007Australian StandardDetermination of the extinction propensity of cigarettesFi
8、rst published as AS 48302007.COPYRIGHT Standards AustraliaAll rights are reserved. No part of this work may be reproduced or copied in any form or by any means, electronic or mechanical, including photocopying, without the written permission of the publisher.Published by Standards Australia, GPO Box
9、 476, Sydney, NSW 2001, AustraliaISBN 0 7337 8098 93AS 48302007PREFACEThis Standard was prepared by Standards Australia Committee CS-102, Reduced Fire Risk Cigarettes. This Standard is based on ASTM E2187-04, Standard test method for measuring the ignition strength of cigarettes. The ASTM method was
10、 the result of over 10 years work and is reported to have been validated by laboratories in the US, but is yet to be validated in Australia. Although no laboratory test is a perfect predictor of the complex and varied causes of fires, this test method has been developed to determine extinction prope
11、nsity of cigarettes.The Standard is downloaded from Standard SharingAccessed by UNIVERSITY OF SOUTH AUSTRALIA on 17 Mar 2007The terms normative and informative have been used in this Standard to define the application of the appendix to which they apply. A normative appendix is an integral part of a
12、 Standard, whereas an informative appendix is only for information and guidance.Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 17 Mar 2007CONTENTSPageFOREWORD. 41SCOPE .5 2APPLICATION . 53REFERENCED DOCUMENTS . 54DEFINITIONS. 55PRINCIPLE . 56HEALTH AND SAFETY OF OPERATORS . 67APPARATUS . 68CALIBRATION
13、 AND STANDARDIZATION . 89TEST SPECIMENS AND STANDARD SUBSTRATE ASSEMBLIES . 1010CONDITIONING . 1111PROCEDURE . 1112TEST REPORT. 13APPENDICESAPROCEDURE FOR SELECTION OF SUBSTRATE ASSEMBLIESFOR TESTING . 14BREPEATABILITY AND REPRODUCIBIITY. 1615AS 48302007FOREWORDA common initiating event in fatal fir
14、es in Australia is the dropping of a lit cigarette onto a bed or piece of upholstered furniture. The cigarette coal heats the furnishing materials to the point where smouldering combustion begins, perhaps followed by a transition to flaming combustion. According to statistics provided by the Nationa
15、l Coroners Information System, carelessly handled cigarettes caused approximately 12% of the fire deaths in Australia from 2000 to 2002.Since limiting the frequency of ignitions is a principal approach to reducing fire loss, it is desirable to establish a test method for the propensity of a cigarett
16、e to remain lit and therefore potentially capable of igniting soft furnishings. This test method uses standard substrates to determine the extent to which, as the substrate draws heat from the cigarette, the cigarette combustion remains strong enough to continue smouldering and thus potentially capa
17、ble of initiating a fire.The Standard is downloaded from Standard SharingAccessed by UNIVERSITY OF SOUTH AUSTRALIA on 17 Mar 2007The test methods ASTM E1352, Test method for cigarette ignition resistance of mock-up upholstered furniture assemblies and ASTM E1353, Test method for cigarette ignition r
18、esistance of components of upholstered furniture have been developed to evaluate the susceptibility of upholstered furniture mock-ups and components to ignition by cigarettes. Standards Australiawww.standards.org.auAccessed by UNIVERSITY OF SOUTH AUSTRALIA on 17 Mar 2007STANDARDS AUSTRALIAAustralian
19、 StandardDetermination of the extinction propensity of cigarettes1 SCOPEThis Standard provides a measure of the capability of a machine-made cigarette, positioned on a standard substrate, as specified in Appendix A, to generate sufficient heat to continue burning and thus potentially cause ignition.
20、This method is applicable to machine-made cigarettes that burn along the length of a tobacco column including filtered and unfiltered machine-made cigarettes.This method does not apply to cigars, cigarillos, loose tobacco or other tobacco products.2 APPLICATIONThis Standard does not purport to addre
21、ss all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Clause 6.3 REFERENCED
22、 DOCUMENTSThe following documents are referenced in this Standard: AS2484FireGlossary of terms2484.1Part 1: Fire testsASTME691Standard practice for conducting an interlaboratory study to determine the precision of a test method4 DEFINITIONSFor the purpose of this Standard, the definitions in AS 2484
23、.1 and those below apply:4.1 Full-length burn (n)The outcome of a determination in which the specimen burns to or past the front plane of the tipping paper, which covers the filter and perhaps a short section of the tobacco column in a filter tip specimen, or past the tips of the metal pins (see Cla
24、use 7.5) if the cigarette specimen has no filter.4.2 Test specimensCigarette samples for testing.4.3 SubstrateHorizontal surface consisting of layers of filter paper on which the test is carried out.5 PRINCIPLEThis test enables comparison of the extinction propensity of different cigarette designs i
25、n standard laboratory conditions.The Standard is downloaded from Standard SharingThe test measures the probability that a specimen, placed on a substrate, will generate sufficient heat to maintain burning of the tobacco column. Each determination consists of placing a lit specimen on the horizontal
26、surface consisting of a set number of layers of filter paper. Observation is made of whether or not the specimen achieves a full-length burn to a point specified in the method. Forty determinations (comprising of one test) are performed on the substrate to obtain the relative probability that the sp
27、ecimen will continue burning despite heat abstraction by the substrate. Alternative substrate selection is detailed in Appendix A.6 HEALTH AND SAFETY OF OPERATORS6.1 GeneralThis test method involves the use of combustible materials that are exposed to ignition sources. Consequently, proper precautio
28、ns shall be taken to avoid thermal injuries.6.2 Smoke inhalation hazardPersonnel shall take proper precautions to avoid inhaling combustion products. The following systems shall be in place:(a) Exhaust systems shall be checked regularly to ensure that they are removing all products of combustion fro
29、m the workplace.(b) Respiratory equipment shall be made available for personnel.6.3 Fire hazardPersonnel shall be instructed on general procedures to handle an unwanted fire. Appropriate fire extinguishing equipment shall be provided to suppress any fires that exceed normal controlled limits.The use
30、r shall ensure that all burning has ceased before discarding used test materials. An appropriate closed metal waste container shall be used in each fire test laboratory for safe disposal of specimens and test assemblies after being exposed to heat and fire.7 APPARATUS7.1 Test and conditioning enviro
31、nmentAccessed by UNIVERSITY OF SOUTH AUSTRALIA on 17 Mar 2007An environmental conditioning room shall be maintained which provides an area adequate for conditioning both specimens and substrate. This room shall be capable of maintaining a relative humidity of 55 5% and a temperature of 23 2C and sha
32、ll be continuously monitored. The room in which the tests are conducted, which may also be the conditioning room, shall be maintained within the same temperature and relative humidity ranges.NOTE: This test method is carried out under laboratory conditions on specimens that have also been exposed to
33、 laboratory conditions. If different conditions are substituted or the end use conditions are changed, it may not be possible, using this test, to predict quantitative changes in the fire test response characteristics measured. Therefore, the quantitative results are valid only for the fire test exp
34、osure conditions described in this procedure.7.2 Test chamberA test chamber, as detailed in Figure 1, shall be constructed of clear plastic such as polymethyl methacrylate (PMMA), nominally 6 mm in thickness. The inside dimensions shall be: height: 340 25 mm, width: 292 6 mm, depth: 394 6 mm. The fu
35、ll front panel of the chamber shall be hinged, with a latch to effect positive closure. The top of the chamber shall have a flattop cylindrical chimney of height 165 13 mm and inside diameter152 6 mm. The chimney shall be centered on the chamber top and sealed to the chamber top panel. Standards Aus
36、traliawww.standards.org.auAccessed by UNIVERSITY OF SOUTH AUSTRALIA on 17 Mar 20077.3 Filter paper holderA cylindrical support for the layers of filter paper, shown in Figure 2, shall be made ofPMMA or similarly rigid material, dimensioned as follows. The outer diameter shall be165 1 mm, the inner d
37、iameter shall be 127 1 mm, and the height shall be 50 1 mm. A recess in the top, 10 2.5 mm deep, shall expand the inner diameter to 152 1 mm. Three or four legs shall raise the bottom of the holder approximately 20 mm above the chamber floor. The outer diameter of the metal rim shall not exceed the
38、inner diameter of the recess in the filter paper holder.7.4 Metal rimA circular brass or other dense metal rim, shown in Figure 2, shall be used to hold the sheets of filter paper flat against each other. The outside diameter of the rim shall be150 2 mm. The inner diameter shall be 130 2 mm. The thi
39、ckness shall be 6.4 1 mm. The rim surface shall be flat and smooth.7.5 Metal pinsA pair of parallel metal pins, each approximately 1 mm in diameter and 8.1 0.05 mm apart, shall protrude 17 4 mm toward the center of the rim. The pins shall be spaced to keep the non-ignited end of a specimen from roll
40、ing, but without pressuring the specimen. The clearance between the pins shall be equal to the nominal diameter of the specimen and located at a height equal to one half of the nominal diameter of the specimen. (See Figure 3.) If specimens of significantly different nominal diameter are to be tested
41、, other pairs of pins, appropriately positioned, shall be inserted into the rim.7.6 Specimen holderA holder shall be used to support the lit specimen in a horizontal position in the test chamber prior to placement of the specimen onto the substrate. A holder shall not clamp the specimen, nor stress it in any other manner and shall not contact the specimen within a nominal 30 mm of its lit end.7.7
