《【英国标准word原稿】BS EN 12911998 nondestructive testing of welds magnetic particale of weldsacc.doc》由会员分享，可在线阅读，更多相关《【英国标准word原稿】BS EN 12911998 nondestructive testing of welds magnetic particale of weldsacc.doc（15页珍藏版）》请在三一办公上搜索。
1、豆丁网：BRITISH STANDARD BS EN1291:1998Incorporating Amendments Nos. 1 and 2Non-destructive testing-,-,-of welds Magnetic particle testing of welds Acceptance levelsThe European Standard EN 1291:1998, with the incorporation of amendments A1:2002 and A2:2003, has the status of a British StandardICS 25.16
2、0.40 第 5 页 共 15 页豆丁网： British Standards InstitutionReproduced by IHS under license with BSI - Uncontrolled CopyDocument provided by IHS Licensee=Bureau Veritas/5959906001, 10/27/200403:17:54 MDT Questions or comments about this message: please call the DocumentPolicy Group at 303-397-2295.BS EN 1291
3、:1998National forewordThis British Standard is the English language version of EN 1291:1998, including amendments A1:2002 and A2:2003.The start and finish of text introduced or altered by amendment is indicated in the text by tags !. Tags indicating changes to CEN text carry the number of the amendm
4、ent. For example, text altered by CEN amendment A1 is indicated by !.As agreed by CEN/TC 121/SC 5 resolution 134/2000 and in accordance with amendment A1:2002, the term “examination” has been replaced by “testing” throughout the document.The UK participation in its preparation was entrusted to Techn
5、ical CommitteeWEE/46, Non-destructive examination, which has the responsibility to:aid enquirers to understand the text;present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed;monitor related international and Eur
6、opean developments and promulgate them in the UK.A list of organizations represented on this committee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalog
7、ue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or ofBritish Standards Online.-,-,-This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its co
8、rrect application.Compliance with a British Standard does not of itself confer immunity from legal obligations.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 5 cover and a back cover.The BSI copyright notice displayed in this document indi
9、cates when the document was last issued.Amd. No.DateComments139881 November 2002See national foreword1493727 April 2004Revision of foreword and deletion Annex ZAThis British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the S
10、tandards Board and comes into effect on 15 June 1998 BSI 27 April 2004ISBN 0 580 29629 6Amendments issued since publicationEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORMEN 1291February 1998+ A1May 2002+A2December 2003ICS 25.160.40Descriptors: Welded joints, refractory materials, steels, quality c
11、ontrol, non-destructive tests, detection, weld defects, magnetic particle testing, acceptability, level : quality, surface conditionEnglish versionNon-destructive testing of welds Magnetic particle testing of welds Acceptance levels(includes amendments A1:2002 and A2:2003)Contrle non destructif des
12、assemblages souds Contrle par magntoscopie des soudures Niveaux dacceptation-,-,-(inclut les amendement A1:2002 et A2:2003)Zerstrungsfreie Prfung von Schweiverbindungen Magnetpulverprfung von Schweiverbindungen Zulssigkeitsgrenzen(enthlt nderung en A1:2002 und A2:2003)This European Standard was appr
13、oved by CEN on 26 January 1998, amendment A1 was approved by CEN on 28 April 2002 and amendment A2 was approved by CEN on 20 November 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a nation
14、al standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any o
15、ther language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany,
16、Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.CENEuropean Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr NormungCentral Secretariat: rue de Stassart 36, B-1050 B
17、russels 1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN nationalMembers.Ref. No. EN 1291:1998 + A1:2002 + A2:2003 EEN 1291:1998Reproduced by IHS under license with BSI - Uncontrolled Copy03:17:54 MDT Questions or comments about this message: please call th
18、e DocumentPolicy Group at 303-397-2295.ForewordThis European Standard has been prepared by Technical Committee CEN/TC 121, Welding, the Secretariat of which is held by DS.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorse
19、ment, at the latest by August 1998, and conflicting national standards shall be withdrawn at the latest by August 1998.This document has been prepared under a mandate given to CEN by European Commission and the European Free Trade Association.According to the CEN/CENELEC Internal Regulations, the na
20、tional standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium,Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and theUnited Kingdom.Fo
21、reword to amendment A1This document EN 1291:1998/A1:2002 has been prepared by Technical Committee CEN/TC 121, Welding, the Secretariat of which is held by DS.This amendment to the European StandardEN 1291:1998 shall be given the status of a national standard, either by publication of an identical te
22、xt-,-,-or by endorsement, at the latest by November 2002, and conflicting national standards shall bewithdrawn at the latest by November 2002.This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requir
23、ements of EU Directive(s).For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.Annex A is informative.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this
24、European Standard: Austria, Belgium,Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and theUnited Kingdom.Foreword to amendment A2This document EN 1291:1998/A2:2003 has been prepared by Technica
25、l Committee CEN/TC 121, Welding, the Secretariat of which is held by DS.This amendment to the European StandardEN 1291:1998 shall be given the status of a national standard, either by publication of an identical textor by endorsement, at latest by June 2004, andconflicting national standards shall b
26、e withdrawn at the latest by June 2004.This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association.According to CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement
27、 this European Standard: Austria, Belgium,Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway,Portugal, Slovakia, Spain, Sweden, Switzerland andthe United Kingdom.ContentsPageForeword21Scope32Normative references33Defini
28、tions34Testing parameters35Acceptance levels4Annex A (informative) Recommended testing parameters52 BSI 27Copyright British Standards InstitutionDocument provided by IHS Licensee=Bureau Veritas/5959906001, 10/27/2004 April 2004EN 1291:19981 ScopeThis European Standard specifies acceptance levels for
29、 indications from imperfections in ferromagnetic steel welds detected by magnetic particle testing.The acceptance levels are primarily intended for use during manufacture testing, but where appropriate they can be used for in service inspection.The acceptance levels in this standard are based on det
30、ection capabilities that can be expected when using techniques specified in EN 1290 and parameters recommended in Annex A. The acceptance levels can be related to welding standards, application standards, specifications or codes. Such a relationship is shown in EN 12062 for EN 25817.2 Normative refe
31、rencesThis European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of the
32、se publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies.EN 1290, Non-destructive testing of welds Magnetic particle testing of welds.prEN 1330-1, Non-destructive testing Te
33、rminology Part 1: General terms.prEN 1330-2, Non-destructive testing Terminology Part 2: Terms common to the non-destructive testing methods.EN 12062, Non-destructive testing of welds General rules for metallic materials.EN 25817, Arc-welded joints in steels Guidance on quality levels for imperfecti
34、ons. (ISO 5817:1992)3 DefinitionsFor the purposes of this standard, in addition with those given in prEN 1330-1, prEN 1330-2and W.I. 138027 (Non-destructive testing Terminology Part 7: Terms used in magnetic particle-,-,-testing)1), the following definitions apply:3.1linear indicationindication havi
35、ng a length greater than three times its width3.2non-linear indicationindication having a length less than, or equal to three times its width4 Testing parametersMany parameters, either individually or in combination, will affect the ability of a technique to detect imperfections of a given size and
36、orientation with respect to the condition of the test surface.Detection of small imperfections is highly dependent on the surface condition of the weld and the detection media used. Examples of the application of these parameters to give a high probability of detection are given in Annex A.1) In pre
37、paration. BSCopyright British Standards Institution I 27 April 20043Document provided by IHS Licensee=Bureau Veritas/5959906001, 10/27/2004EN 1291:19985 Acceptance levels5.1 GeneralThe width of the test surface shall include the weld metal and the adjacent parent metal up to a distance of 10 mm on e
38、ach side.Acceptance levels prescribed for linear indications are those corresponding to the evaluation level. Indications lower than this shall not be taken into account. Normally, acceptable indications shall not be recorded.Local grinding may be used to improve the classification of all or just pa
39、rt of a test surface, when it is required to work to a higher detection limit than that expected by the existing weld surface condition.5.2 Grouped indicationsAny adjacent indications separated by less than the major dimension of the smaller shall be assessed as a single, continuous indication.Group
40、ed indications shall be evaluated in accordance with application standards.5.3 Removal of imperfectionsWhere the product specification permits, local grinding may be used to reduce or remove imperfections which are the cause of unacceptable indications. !All such areas shall be re-tested and evaluat
41、ed with the same magnetic system and technique.!Acceptance levels are given in Table 1.Table 1 Acceptance levels for indicationsDimensions in millimetresType of indicationAcceptance level1123Linear indicationl = length of indicationl k 1,5l k 3l k 6Non-linear indicationd = major axis dimensiond k 2d
42、 k 3d k 41 Acceptance levels 2 and 3 may be specified with a suffix “X” which denotes that all linear indications detected shall be assessed to level 1. However, the probability of detection of indications smaller than those denoted by the original acceptance level can be low.-,-,-4Copyright British
43、 Standards Institution BSI 27Document provided by IHS Licensee=Bureau Veritas/5959906001, 10/27/2004 April 2004EN 1291:1998Annex A (informative) Recommended testing parameters-,-,-Recommended testing parameters for reliable detection of small imperfections are given in Table A.1. The surfaces are in
44、 the as welded condition. It can be necessary to improve the surface condition e.g. by abrasive paper or local grinding to permit accurate interpretation of indications. The detection media are given in order of preference.Table A.1 Recommended testing parametersAcceptance levelSurface conditionDete
45、ction media1Fine surface1Fluorescent or colour contrast with contrast aid2Smooth surface2Fluorescent or colour contrast with contrast aid3General surface3Colour contrast with contrast aid or fluorescent1 Fine surfaceThe weld cap and parent material offering smooth clean surfaces with negligible undercut, rippling and s
