《【BS英国标准】BS EN 84032004 Mobile waste containers — Part 3 Containers with 4 wheels with a cap.doc》由会员分享，可在线阅读，更多相关《【BS英国标准】BS EN 84032004 Mobile waste containers — Part 3 Containers with 4 wheels with a cap.doc（25页珍藏版）》请在三一办公上搜索。
1、Licensed copy: The University of Hong Kong, The University of Hong Kong, Version correct as of 26/03/2009 08:59, (c)BSIBRITISH STANDARDBS EN840-3:2004Mobile waste containers Part 3: Containers with 4 wheels witha capacity up to 1 300 l with dome lid(s), for trunnion and/or comb liftingdevices Dimens
2、ions and designThe European Standard EN 840-3:2004 has the status of aBritish StandardICS 13.030.40 BS EN 840-3:2004National forewordThis British Standard is the official English language version ofEN 840-3:2004. It supersedes BS EN 840-3:1997 which is withdrawn.The UK participation in its preparati
3、on was entrusted by Technical Committee B/508, Waste management, to Subcommittee B/508/1, Waste containers and associated lifting devices, which has the responsibility to:aid enquirers to understand the text;present to the responsible international/European committee any enquiries on the interpretat
4、ion, or proposals for change, and keep the UK interests informed;monitor related international and European developments and promulgate them in the UK.A list of organizations represented on this subcommittee can be obtained on request to its secretary.Cross-referencesThe British Standards which impl
5、ement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication doe
6、s not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard does not of itself confer immunity from legal obligations.Licensed copy: The University of Hong Kong, The University of Hong Kong, Version correct
7、 as of 26/03/2009 08:59, (c)BSIThis British Standard was published under the authority of the Standards Policy and Strategy Committee on18 March 2004 BSI 18 March 2004ISBN 0 580 43567 9Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 20, an
8、inside back cover and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amd. No.DateCommentsAmendments issued since publicationEUROPEAN STANDARD NORME EUROPENNEEUROPISCHE NORMEN 840-3March 2004ICS 13.030.40Supersedes EN 840-3:1997English ver
9、sionMobile waste containers - Part 3: Containers with 4 wheels with a capacity up to 1 300 l with dome lid(s), for trunnion and/or comb lifting devices - Dimensions and designConteneurs roulants dchets - Partie 3: Conteneurs 4 roues de capacit infrieure ou gale 1300 l couvercle(s) bomb(s), pour lve-
10、conteneurs par tourillon et/ou peigne - Dimensions et conceptionFahrbare Abfallsammelbehlter - Teil 3: Behlter mit 4Rdern und einem Nennvolumen bis 1300 l mit Schiebedeckel(n), fr Schttungen fr Zapfenaufnahme und/oder fr Kammschttungen - Mae und FormgebThis European Standard was approved by CEN on 1
11、0 December 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may
12、be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Centra
13、l Secretariat has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Polan
14、d, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATION C O M I T EUR O P EN DE NOR M A L I S A TI ON EUR O P I S C H ES KOM I TEE F R NOR M UNG Management Centre: rue de Stassart, 36 B-1050 BrusselsLicensed copy: The University of Hong K
15、ong, The University of Hong Kong, Version correct as of 26/03/2009 08:59, (c)BSI 2004 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members.Ref. No. EN 840-3:2004: EEN 840-3:2004 (E)Licensed copy: The University of Hong Kong, The University of Hong Ko
16、ng, Version correct as of 26/03/2009 08:59, (c)BSIContentspageForeword . 31Scope . 42Normative references . 43Terms and definitions. 44Volumes . 55Dimensions and design. 56Nominal Load . 67Safety and health requirements . 68Testing . 69Marking . 610Designation. 7Annex A (informative) Recommendations
17、 for manufacturers of lifting devices . 18Annex B (informative) A-Deviations . 2019Licensed copy: The University of Hong Kong, The University of Hong Kong, Version correct as of 26/03/2009 08:59, (c)BSIForewordThis document (EN 840-3:2004) has been prepared by Technical Committee CEN/TC 183 “Waste m
18、anagement”, the secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2004, and conflicting national standards shall be withdrawn at the latest by September
19、 2004.This document supersedes EN 840-3:1997.This draft European Standard is one part of the series of standards of EN 840 about Mobile waste containers comprising the following parts:Part 1:Containers with 2 wheels with up to 400 l for comb lifting devices - Dimensions and design.Part 2:Containers
20、with 4 wheels with a capacity up to 1 300 l with flat lid(s), for trunnion and/or comb lifting devices - Dimensions and design.Part 3:Containers with 4 wheels with a capacity up to 1 300 l with dome lid(s), for trunnion and/or comb lifting devices - Dimensions and design.Part 4:Containers with 4 whe
21、els with a capacity up to 1 700 l with flat lid(s), for wide trunnion or BG and/or wide comb lifting devices - Dimensions and design.Part 5:Performance requirements and test methods. Part 6:Safety and health requirements.Annexes A and B are informative.According to the CEN/CENELEC Internal Regulatio
22、ns, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway
23、, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.Licensed copy: The University of Hong Kong, The University of Hong Kong, Version correct as of 26/03/2009 08:59, (c)BSI1ScopeThis European Standard specifies dimensions and design requirements of mobile waste conta
24、iners with 4 wheels, with dome lid(s) and capacity up to 1300 l to be used by trunnion and/or comb lifting device.2Normative referencesThis European Standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate place
25、s in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referr
26、ed to applies (including amendments).EN 840-1:2004, Mobile waste containers Part 1: Containers with 2 wheels with a capacity up to 400 l for comb lifting device - Dimensions and design.EN 840-2:2004, Mobile waste containers Part 2: Containers with 4 wheels with a capacity up to 1 300 l with flat lid
27、(s), for trunnion and/or comb lifting devices - Dimensions and design.EN 840-5, Mobile waste containers Part 5: Performance requirements and test methods.EN 840-6, Mobile waste containers Part 6: Safety and health requirements.EN 1501-1, Refuse collection vehicles and their associated lifting device
28、s General requirements and safety requirements Part 1: Rear-end loaded refuse collection vehicles.EN ISO 11469, Plastics - Generic identification and marking of plastics products (ISO 11469:2000).3Terms and definitionsTerms for components of mobile waste containers and lifting devices in three langu
29、ages are given in annex Aof EN 840-1:2004.For the purposes of this European Standard, the following terms and definitions apply.3.1mobile waste containerappropriately designed container fitted with wheels intended to temporarily store waste3.2lifting devicestructure which picks-up, tilts and empties
30、 containers3.3comb lifting devicelifting device in which the picking-up system consists of a row of teeth and a locking system to retain the container during emptying3.4trunnion lifting devicelifting device in which the picking-up system consists of a pair of arms with automatic locking mechanism to
31、 fit the trunnion to retain the container during emptyingLicensed copy: The University of Hong Kong, The University of Hong Kong, Version correct as of 26/03/2009 08:59, (c)BSI3.5 volumetotal space inside the container when the lid is closed3.6nominal volumevolume stated by the manufacturer (see Tab
32、le 1 without tolerances)3.7 capacityfor the purpose of this standard nominal volume and capacity are deemed to be the sameNOTEThe English term capacity and the French term capacit are translated in the German version by the termNennvolumen.3.8nominal loadload mass, which is calculated as given in cl
33、ause 63.9total permissible massmass of the container plus the nominal load3.10functional and safety dimensionsessential dimensions which ensure the functionality and interchangeability of the container with the compatible lifting device and which are necessary for the operators safety and health.4Vo
34、lumesThis part of EN 840 identifies the two classes of containers: Class I - small size (nominal volume up to 1 000 l); Class II - large size (nominal volume between 1 000 l and 1 300 l).Within the two above-mentioned classes of containers the following volumes are identified: 770 l, 1 000 l,1 100 l
35、 and 1 300 l. Nominal volumes different from those referenced can be used by agreement between user and manufacturer. The tolerance of the volumes shall be 5 % maximum measured according to EN 840-5.5Dimensions and design5.1The design of the containers need not to correspond to the drawings given in
36、 Figures 1a to 1c. The functional dimensions given in Table 1 shall be respected. Recommendations for manufacturers of lifting devices are given in annex A (see also EN 1501-1).5.2The container shall be constructed so that when it is unloaded or loaded with a nominal load (see clause 6), it fits on
37、an approved compatible lifting device. It shall be automatically locked safely into the lifting device during the lifting operation. If the container is equipped with a comb receiver, it shall correspond to at least one of the options given in Figure 2 (Form A, B or C).5.3The lid(s) shall fit the bo
38、dy. It/they shall be made with at least 2 fixing points and have at least one means for opening.Licensed copy: The University of Hong Kong, The University of Hong Kong, Version correct as of 26/03/2009 08:59, (c)BSI5.4Handles fitted in front of the trunnion shall have a measurement over the handles
39、of 10 mm less than the actual measurement in Table 1, dimension N 33. Also the handles and their location shall be designed so that they do not damage the operator.5.5If the container has ribs in the frontal receiver they shall meet the requirements of Figures 2 and 5.5.6The container shall have 4 s
40、wivel castors. Each swivel castor shall be capable of withstanding 1/3 of the total permissible mass. Each castor shall meet the requirements of EN 840-5. The container shall have facilities for mounting the castor platine according to at least one of the measurements as shown in Figure 6.5.7All the surfaces of the container including design features shall be smooth and free of any foreign bodies or flaws.5.8The container should have a drain plug.5.9When direction locks are fitted they shall be fixed on at least 2 castors.5.10 The container should be fitted with 2 braked
