《Concrete Stamping and Stenciling Systems：具体的冲压和制版系统.doc》由会员分享，可在线阅读，更多相关《Concrete Stamping and Stenciling Systems：具体的冲压和制版系统.doc（7页珍藏版）》请在三一办公上搜索。
1、Legacy Decorative Concrete Systems, Inc.July 20073421 Lumber LaneSpringfield, Illinois 62707Toll Free(866) 684-9394Phone(217) 522-6737Fax(866) 684-9395WebsiteE-mailtechnicalsupportProduct Guide SpecificationSpecifier Notes: This product guide specification is written according to the Construction Sp
2、ecifications Institute (CSI) 3-Part Format, including MasterFormat, SectionFormat, and PageFormat, as described in The Project Resource ManualCSI Manual of Practice, Fifth Edition.The section must be carefully reviewed and edited by the Architect to meet the requirements of the project and local bui
3、lding code. Coordinate this section with other specification sections and the Drawings. Delete all “Specifier Notes” after editing this section.Section numbers are from MasterFormat 1995 Edition, with numbers from MasterFormat 2004 Edition in parentheses. Delete version not required.SECTION 03360 (0
4、3 35 33)CONCRETE STAMPING STENCILING SYSTEMSpecifier Notes: This section covers Legacy Decorative Concrete Systems, Inc. “Impressions” concrete stamping system and “FauxCrete” concrete stenciling system. Both systems create colors and patterns into freshly placed horizontal concrete surfaces. Consul
5、t Legacy Decorative Concrete Systems, Inc. for assistance in editing this section for the specific application.Use section number 03360 (03 35 33) when specifying “Impressions” concrete stamping system. Use section number 03360 (03 35 36) when specifying “FauxCrete” concrete stenciling system.PART 1
6、GENERAL1.1SECTION INCLUDESSpecifier Notes: Throughout this product guide specification, use “concrete stamping system” when specifying “Impressions” and use “concrete stenciling system” when specifying “FauxCrete”.Specify one of the following decorative concrete systems.A.Decorative concrete stampin
7、g system.B.Decorative concrete stenciling system.1.2RELATED SECTIONSSpecifier Notes: Edit the following list of related sections as required for the project. List other sections with work directly related to this section.A.Section 03300 (03 30 00) Cast-in-Place Concrete.1.3REFERENCESSpecifier Notes:
8、 List standards referenced in this section, complete with designations and titles. This article does not require compliance with standards, but is merely a listing of those used.A.ASTM C 979 Standard Specification for Pigments for Integrally Colored Concrete.1.4SUBMITTALSA.Comply with Section 01330
9、(01 33 00) Submittal Procedures.B.Product Data: Submit manufacturers product data, including application instructions.C.Samples: Submit manufacturers samples of standard colors.D.Manufacturers Certification: Submit manufacturers certification that materials comply with specified requirements and are
10、 suitable for intended application.E.Applicators Project References: Submit applicators list of successfully completed concrete stamping concrete stenciling projects, including project name and location, name of architect, and type and quantity of materials applied.1.5QUALITY ASSURANCEA.Applicators
11、Qualifications:1.Applicator regularly engaged, for preceding 5 years, in application of concrete stamping systems concrete stenciling systems of similar type to that specified.2.Employ persons trained for application of concrete stamping systems concrete stenciling systems.Specifier Notes: Edit the
12、following paragraph for mock-ups as required for the project.B.Mock-ups:1.Construct mock-ups of concrete stamping system concrete stenciling system and illustrating floor finishes, using same materials for use in the Work.2.Construct mock-ups at location determined by Architect.3.Construct mock-ups
13、a minimum size of 48 inches by 48 inches.4.Receive approval of mock-ups by Architect for patterns, colors, textures, special effects, and workmanship before application of concrete stamping system concrete stenciling system.5.Approved mock-ups will be the standard for patterns, colors, textures, spe
14、cial effects, and workmanship of concrete stamping system concrete stenciling system.Specifier Notes: Edit pre-application meeting as required for the project.C.Pre-application Meeting:1.Convene pre-application meeting before start of application of concrete stamping system concrete stenciling syste
15、m.2.Require attendance of parties directly affecting work of this section, including Contractor, Architect, applicator, and manufacturers representative.3.Review preparation, application, protection, and coordination with other work.1.6DELIVERY, STORAGE, AND HANDLINGA.Delivery: Deliver materials to
16、site in manufacturers original, unopened containers and packaging, with labels clearly identifying product name and manufacturer.B.Storage:1.Store materials in clean, dry area indoors in accordance with manufacturers instructions.2.Store out of direct sunlight.3.Keep from freezing.C.Handling: Protec
17、t materials during handling and application to prevent contamination or damage.1.7ENVIRONMENTAL REQUIREMENTSA.Do not apply concrete stamping system concrete stenciling system when air or surface temperatures are below 40 degrees F (4 degrees C) or above 90 degrees F (32 degrees C) during application
18、 or within 24 hours after application.B.Do not apply concrete stamping system concrete stenciling system when rain, snow, or excessive moisture is expected during application or within 24 hours after application.PART 2PRODUCTS2.1MANUFACTURERA.Legacy Decorative Concrete Systems, Inc., 3421 Lumber Lan
19、e, Springfield, Illinois 62707. Toll Free (866) 684-9394. Phone (217) 522-6737. Fax (866) 684-9395. Website . E-mail technicalsupport.2.2MATERIALSSpecifier Notes: Specify “Impressions” concrete stamping system or “FauxCrete” concrete stenciling system. Delete system not required. Consult Legacy Deco
20、rative Concrete Systems, Inc. for more information.A.Concrete Stamping System: “Impressions”.Specifier Notes: Specify required components of “Impressions” concrete stamping system. Delete components not required. Consult Legacy Decorative Concrete Systems, Inc. for more information.1.Cementitious Dr
21、y-Shake Material: “Colour-Hard”.Specifier Notes: Specify required colors. Delete colors not required.a.Color: Antique White Ash White Autumn Black Bluestone Bone Brick Red Canyon Red Charcoal Coronado Cream Beige Desert Tan Federal Red Federal Yellow Light Grey Mesa Nutmeg Pecan Plum Quarry Red Rust
22、 Saddle Brown Sage Sand Shadow Slate Stone Grey Terra Cotta Venetian Pink.2.Liquid Integral Color: “ColorFlo”.a.Conformance: ASTM C 979.Specifier Notes: Specify required colors. “ColorFlo” is available in 64 liquid integral colors or custom-color options. Consult Legacy Decorative Concrete Systems,
23、Inc. for more information.b.Color: _ .3.Pigmented Dry-Powder Release: “Accent-Colour Release”.Specifier Notes: Specify required colors. Delete colors not required.a.Color: Antique White Ash White Autumn Black Bluestone Bone Brick Red Canyon Red Charcoal Coronado Cream Beige Desert Tan Federal Red Fe
24、deral Yellow Light Grey Mesa Nutmeg Pecan Plum Quarry Red Rust Saddle Brown Sage Sand Shadow Slate Stone Grey Terra Cotta Venetian Pink.4.Liquid Release: “Accent-Liquid Release”.5.Tooling: Mat-type imprinting tools.Specifier Notes: Specify required patterns. Mat-type imprinting tools are available i
25、n a large number of patterns. Consult Legacy Decorative Concrete Systems, Inc. for more information.a.Pattern: _ .6.Concrete Stain: “Fresco Stain” “Tinte DAcqua”.Specifier Notes: Specify required colors. Delete colors not required. Special colors and effects can be produced by using one or more appl
26、ications, blending two or more colors, blending “Fresco Stain” with “Fresco Stain Plus”, or blending “Tinte DAcqua” with water.a.“Fresco Stain” Colors: Amber Aspen Caribbean Clay Copper Forest Green Hickory Peppercorn.b.“Tinte DAcqua” Colors: Aged Bronze Aged Patina Antebellum Aqua Baltic Bernado Bl
27、ack Breccia Canyon Coral Red Dried Basil Essence Granada Granite Gulf Magnet Mediterranean Metalica Orange Patina Pewter Roma Taiga Brown Terra Tomatillo Tuscan Venetian Clay Walnut.7.Concrete Sealer:Specifier Notes: Specify one of the following five concrete sealers as required to achieve the desir
28、ed finish. Consult Legacy Decorative Concrete Systems, Inc. for more information.a.High-Gloss Finish, Interior or Exterior Use: “Premium Seal VOC 100”.b.Gloss Finish, Interior or Exterior Use: “Signature Seal VOC”.c.Low to Medium-Gloss Finish, Interior or Exterior Use: “Magnum Seal”.d.Low-Sheen, Mat
29、te Finish, Interior or Exterior Use: “AquaClear VOC”.e.Satin Finish, Interior or Exterior Use: “Signature Satin 400”.B.Concrete Stenciling System: “FauxCrete”.Specifier Notes: Specify required components of “FauxCrete” concrete stenciling system. Delete components not required. Consult Legacy Decora
30、tive Concrete Systems, Inc. for more information.1.Cementitious Dry-Shake Material: “Colour-Hard”.Specifier Notes: Specify required colors. Delete colors not required.a.Color: Antique White Ash White Autumn Black Bluestone Bone Brick Red Canyon Red Charcoal Coronado Cream Beige Desert Tan Federal Re
31、d Federal Yellow Light Grey Mesa Nutmeg Pecan Plum Quarry Red Rust Saddle Brown Sage Sand Shadow Slate Stone Grey Terra Cotta Venetian Pink.2.Liquid Integral Color: “ColorFlo”.a.Conformance: ASTM C 979.Specifier Notes: Specify required colors. “ColorFlo” is available in 64 liquid integral colors or
32、custom-color options. Consult Legacy Decorative Concrete Systems, Inc. for more information.b.Color: _ .3.Pigmented Dry-Powder Release: “Accent-Colour Release”.Specifier Notes: Specify required colors. Delete colors not required.a.Color: Antique White Ash White Autumn Black Bluestone Bone Brick Red
33、Canyon Red Charcoal Coronado Cream Beige Desert Tan Federal Red Federal Yellow Light Grey Mesa Nutmeg Pecan Plum Quarry Red Rust Saddle Brown Sage Sand Shadow Slate Stone Grey Terra Cotta Venetian Pink.4.Stencils: “FauxCrete”.a.22-mil-thick, water-resistant, plastic-coated, fiberboard pattern stenci
34、ls.Specifier Notes: Specify required patterns. Delete patterns not required.b.Pattern: Ashlar Slate Basketweave Brick Cobblestone Header Diamond Tile Face Brick Fishscale Flagstone Herringbone Brick Large Cobblestone Circle Mock Herringbone Brick Old Chicago Brick Old English Cobblestone Pinwheel Ru
35、nningbond Brick Rustic Brick Silverdale Small Cobblestone Circle Soldier Course Brick Stacked Bond Brick Vertical Face Brick.5.Concrete Stain: “Fresco Stain” “Tinte DAcqua”.Specifier Notes: Specify required colors. Delete colors not required. Special colors and effects can be produced by using one o
36、r more applications, blending two or more colors, blending “Fresco Stain” with “Fresco Stain Plus”, or blending “Tinte DAcqua” with water.a.“Fresco Stain” Colors: Amber Aspen Caribbean Clay Copper Forest Green Hickory Peppercorn.b.“Tinte DAcqua” Colors: Aged Bronze Aged Patina Antebellum Aqua Baltic
37、 Bernado Black Breccia Canyon Coral Red Dried Basil Essence Granada Granite Gulf Magnet Mediterranean Metalica Orange Patina Pewter Roma Taiga Brown Terra Tomatillo Tuscan Venetian Clay Walnut.6.Concrete Sealer:Specifier Notes: Specify one of the following five concrete sealers as required to achiev
38、e the desired finish. Consult Legacy Decorative Concrete Systems, Inc. for more information.a.High-Gloss Finish, Interior or Exterior Use: “Premium Seal VOC 100”.b.Gloss Finish, Interior or Exterior Use: “Signature Seal VOC”.c.Low to Medium-Gloss Finish, Interior or Exterior Use: “Magnum Seal”.d.Low
39、-Sheen, Matte Finish, Interior or Exterior Use: “AquaClear VOC”.e.Satin Finish, Interior or Exterior Use: “Signature Satin 400”.PART 3EXECUTION3.1EXAMINATIONA.Examine surfaces to receive concrete stamping system concrete stenciling system.B.Notify Architect of conditions that would adversely affect
40、application.C.Do not begin application until unacceptable conditions are corrected.3.2PREPARATIONA.Protect adjacent areas, adjoining walls, and landscaping from contact with concrete stamping system concrete stenciling system.3.3APPLICATIONA.Apply concrete stamping system concrete stenciling system
41、in accordance with manufacturers instructions at locations indicated on the Drawings.B.Form and place concrete as specified in Section 03300 (03 30 00).C.Match approved mock-ups for patterns, colors, textures, special effects, and workmanship.D.Concrete Sealer:1.Apply concrete sealer in accordance w
42、ith manufacturers instructions after substrate has thoroughly dried.2.Uniformly apply concrete sealer over entire surface.3.4PROTECTIONA.Protect completed concrete stamping system concrete stenciling system application from:1.Rain, Snow, and Excessive Moisture: Minimum of 24 hours.2.Foot Traffic: Minimum of 24 hours.3.Vehicle Traffic: Minimum of 72 hours.B.Protect applied concrete stamping system concrete stenciling system from damage during construction.END OF SECTION
