《HUDE 安全气囊点爆试验系统技术.doc》由会员分享，可在线阅读，更多相关《HUDE 安全气囊点爆试验系统技术.doc（5页珍藏版）》请在三一办公上搜索。
1、HUDE安全气囊点爆试验系统技术整套静态点爆系统适用于 DAB、PAB、SAB 和 CAB 试验。交货范围： - 安全气囊静态点爆试验系统带 6 个点爆通道，触发时间管理，和点火脉 冲瞬间数据采集 - 高速照相机像速 2000 桢/秒，2 台照相机 - 照明系统，用于照相机影像 - P-T 气体发生器试验套件 - 28.3 与 60 升气罐 - 中国杭州交货 - 在客户现场安装调试 - TEMPERATURE CHAMBER by Zenda - 环境箱（上海增达） - VENTILATION system 1 set - 排烟系统一套 I. 安全气囊静态点爆实验室结构 包括设计，生产，组装，
2、安装，安装监控，检验，CIP 交货，说明书，操作员培训，服务 和设备保单。 细节描述见III，供货范围 安全气囊实验室设备示意图Page 2 / 20 II. DELIVERY TERMS 交货条件：设备要求： 控制系统 230VAC，50Hz单相，最大 1kVA 卤素照明系统 400VAC，50Hz3 相，220kVA交货时间： 收到订单且确认订单后 10-12 周质保期: 最终验收后 12 个月保单有效期，如果客户要求 24 个月保单需要额外下订单。.Page 3 / 20 III. 供货范围Sub-Item:项目1.0 Chanber 环境箱1.1 Storage chamber 储存箱
3、 1台1.2 Test Chamber with automatic Door 1台 自动开门试验箱2.0 高速照相机，包括镜头，支架，电源和附件2.1 IDT MOTION XTRA N4 彩色摄像机 2台3.0 照明系统 1套4.0 安全气囊静态点爆试验系统 1套5.0 60L 气罐 1套 用于安全气囊气体发生器试验6.0 28.3L 气罐 1套 用于安全气囊气体发生器试验7.0 压力试验传感器套件 1套 压阻式压力传感器套件带信号放大器8.0 气体发生器试验软件包含 USCAR 选项 1套9.0 VENTILATION HOOD AND DUCT 排风系统 1套10.0 在客户现场交钥匙
4、安装11.0 PRE-ACCEPTANCE 预验收Page 4 / 20 IV. 技术规格1.0 Chanber 环境箱1.1 Storage chamber 储存箱 1 pieceKEY TECHNICAL SPECIFICATIONS OF SOAK CHAMBER 主要技术参数 Interior dimension: D 800mmW 1000mmH 1200mm 内部尺寸：800mm 深 1000mm 宽 1200mm 高 Exterior dimension: D 1360mmW 1500mmH 2020mm 外部尺寸：1360mm 深 1500mm 宽 2020mm 高 Tempe
5、rature range: -40 to 110C 温度范围：-40 to 110C Temperature variation: /-0.5C 温度波动性：/-0.5C Temperature difference: /-2C 温度偏差：/-2C Temperature contrast: lt2C 温度均匀性：/-2C Temperature rise speed: 升温速率 From 25C to 110C duration lt 50mins With load 25C to 110C 50 分钟以内 （带载） Temperature fall speed: 降温速率 From 25C
6、 to 40C durationlt65minsWith load 25C to 40C 65 分钟以内 （带载） Load: 75kg Al 载荷：75Kg 铝 Note: All the above specifications are measured in the room temperature of 25C temperature performance test is measured according to the related regulations of national standards of JJF1101-2003. 注：上述性能测定于环境温度为25C 的条件下
7、，温度测定标准依据JJF1101-2003 国家标准 The noise from the machinery is less than 68dB. 噪音：低于68dB Cabinet Structural Features 环境箱结构特点 Exterior wall materials : Plastic-sprayed steel-tin 外壳：喷塑钢板 Interior wall materials : stainless steel plate 内胆：不锈钢 Heat insulation materials: Hard Poly Urethane foamed plastic and
8、 advanced glass fibre 绝热材料：聚氨酯泡沫塑料 Standard configuration : 2 fluorescent lamp 2 shelves. We quote more shelves on request. 标准配置：两个荧光灯、两个隔架 The cabinet is equipped with the 1 d100mm cable ports with the sealing cap and silicone plugs. 环境箱配有一个100mm 直径的电缆孔，以及相应的硅橡胶密封塞及盖子 Door: Manual wing doors open d
9、imension: W 2000mmH 1500mm 门：手动门，尺寸：2000mm 宽H 1500mm 高 Windows with full-pane heaters to help keep condensation and frost clear:Page 5 / 20 Dimension W470H320mm Amount: 1 in door 观察窗：一个，有效视界：470mm 宽320mm 高，带加热装置 Air-conditioning System 空气调节系统 Regulation and control: Air-compulsory cycle balance temp
10、erature regulation 控制及调节：空气强制循环平衡温度调节 Air-cycle equipment: Centrifugal blast fan 空气循环装置：离心风机 Heating: Nickel-chromium alloy heating wire heater 加热：镍铬金属丝加热器 Humidifier:18-12-2.5 Cr-Ni-Mo stainless steel sheathed heater surface evaporating system 加湿器：18-12-2.5 Cr-Ni-Mo 不锈钢铠装加热器 Air cooling: Steam comp
11、ression cooling 空气冷却：蒸汽压缩制冷 Temperature measurer and sensor: Shielded heat resistance Pt100 温度测量传感器：铠装Pt100 热电阻 Cooling System 制冷系统 Coolant: Environment-friendly Fluorine coolant R404aR23 冷媒：R404aR23 Cooling compressor: “Lunite Hermetique TAG4573 6.5HP”2 fully enclosed compressor France 制冷压缩机：2 台全封闭
12、压缩机 Condensation mode: Built in cooling condenser 冷凝模式：内置冷凝器 Refrigeration mode: Mechanical compressed single amp double stage refrigeration. 制冷模式：机械压缩单/双级制冷 Control system:控制系统 Type of controller: ZD-600 控制器型号：ZD-600 Language: English 预言：英文 M-M interface: 6.4” TFT liquid-crystal color display 人机界面：
13、6.4” TFT 液晶显示屏 Setting: Touch panel method 设置方式：触摸屏方式 Resolution: Temperature: 0.1C time: 1min 显示分辨率：温度：0.1C，时间：1 分钟 Set-range: temperature: Temperature:-100 300C 温度设定范围：-100 300C User procedure capacity: 1000 programmable procedures withmaximal 1000 stepssegments in each procedure1000 cycle steps a
14、nd the procedures is linkable 编程能力：最多1000 个程序，每个程序最多1000 个步骤 Operation mode: constant value operation procedure operation 运行方式：程序方式、定值方式 Experimental data display: preset temperature measured temperature total operation time segment operation time segment remaining time heating status and possible r
15、eason 试验参数显示：设定温度、实测温度、总运行时间、程序段运行时间、程序段保留时间、加热状态、提示等 Failure information: in abnormal case display the failure status and possible information 故障信息：故障报警及原因、处理提示功能 Equipped with LAN interface to PC and installed with the software to set parameters and records of temperature parameters with the softw
16、are for PC printer 配有与PC 连接的LAN 接口，可通过计算机及相关软件设定参数及纪律相关数据 Automatic selection of coolers working status: according to different experimental conditions select the coolers working status. 自动选择压缩机工作状态 Security protection system:保安装置 Over-temperature protection过温保护 Over-pressure protection 过压保护 Overloa
17、d protection of motor马达过载保护 Overheat protection of motor马达过热保护 Over-pressure protection of cooling compressor压缩机过压保护 Overheat protection of cooling compressor 压缩机过温保护 Over-current protection of cooling compressor 压缩机过流保护 Fuse for control and lighting circuit 保险丝（防止控制回路和照明回路短路） Equipment working cond
18、ition: 设备工作环境要求 Environment:环境Page 6 / 20 Ambient temperature: 15C to 35C 温度：15C to 35C Relative humidity: lt85RH 相对湿度：lt85RH Quality of ambient air: no high-density powder and combustible or explosive gas or powder. 空气质量：无高浓度颗粒物或爆炸性气体 Power supply:电源 Power voltage: AC38010V 3-phase 4-wire ground wi
19、re protection 电压：交流38010V，3 相5 线制 Frequency: 50/-0.5Hz 频率：50/-0.5Hz MAX. Power:18KW 最大功率：18KW MAX. Current: 27 A 最大电流：27A Recording function: The memory of the controller can record the test date for 3 month and the date can be downloaded by USB. 记录功能：控制器内存可纪律3 个月的测试数据，数据可通过USB 接口导出 After-sale servi
20、ce: 保修 Charge-free warranty will last for 2 years from the date of equipment delivery. After the warranty period the user will be charged properly. Irregular examination and life-long service are available. 2 年保修期 Technical training:技术培训 Provide charge-free training to 2 operators for each user in t
21、he company or the user site. 提供2 名操作者的免费培训 Accessories: 附件 The certificate of quality: one copy Warranty card: one copy 质量合格证书：一份；保修卡：一份 Instruction Manual: one copy Controller Manual: one copy 指导手册：一份；控制器手册：一份 Circuit diagram: one copy 电路图：一份Page 7 / 201.2 Test Chamber with automatic Door 自动开门试验箱 1
22、 piece Automatic Main Test Chamber 自动开门试验箱Key Technical Specifications Main Test Chamber 主要技术指标主试验箱 Interior dimension 内尺寸: D 1300mmW 2800mmH 1300mm Exterior dimension 外尺寸: closed 门关闭 app. 2800mm x 3100mm x 2300mm opened 门开启app. 4200mm x 1600mm x 2300mm Temperature range: -40C to 110C 温度范围：-40C to 1
23、10C Temperature variation: /-0.5C 温度波动性：/-0.5C Temperature difference:/-2C 温度偏差：/-2C Temperature contrast:lt /-2C 温度均匀性：/-2C Temperature rise speed with thermal load of 50kg 升温速率（带载50Kg） From 40C to 110C durationlt 70min 40C to 110C 小于70 分钟 Temperature fall speed with thermal load 降温速率： From 25C to
24、40C durationlt70mins 25C to 40小于70 分钟 Thermal load: 150kg Fe热载荷：150KgFe Noise of the machinery is less than 72dB. 噪音：小于72dB Note: All the above specifications are measured in the room temperature of 25C temperature performance test is measured according to the related regulations of national standar
25、ds of JJF1101-2003. 注：上述性能测定于环境温度为25C 的条件下，温度测定标准依据JJF1101-2003 国家标准 Cabinet Structural Features 箱体结构 Like pos. 1.1 同1.1Page 8 / 20 Additional Automatic Flip Door 自动翻转门 Gate: Automatic Up-down open door dimension W 3100mm H 1600mm 门：自动翻转门，尺寸：3100mm 1600mm Duration of open door: less than 10 seconds
26、Bearing: 100kg test load on automatic door Pneumatic Drive 开门时间：小于10 秒钟，门负载：100Kg，驱动方式：气动 Aluminium or sandwich compound desk plate with M8 thread holes in 100 x 100 mm grid 门上装有螺距为100 x 100 mm 的M8 螺孔矩阵的铝平板 Air-conditioning System 空气调节系统 Like pos. 1.1 同1.1 Cooling System: Air cooling 冷却方式：空冷 Like po
27、s. 1.1 同1.1 Control system:控制系统 Like pos. 1.1同1.1 Security protection system:安保装置 Like pos. 1.1同1.1 Equipment working condition: 设备工作条件 Like pos. 1.1同1.1 Power supply 电源 Power voltage: AC38010V 3-phase 4-wire ground wire protection 电压：AC38010，3相5线制 Frequency: 500.5Hz 频率：500.5Hz Power switch: air swi
28、tch knife-switch not allowed 电源开关：空气开关 MAX. Power: 20KW 最大功率：20KW MAX. Current: 30A 最大电流：30A After-sale service:保修 Like pos. 1.0同1.0 Technical training:技术培训 Like pos. 1.0同1.0 Accessories: 附件 Like pos. 1.0同1.0 1.2.1 TEST TABLE FOR AMBIENTE TEST 23C 1 piece 4.40000 EUR 测试平台（室温情况下使用） heavy duty table a
29、pprox. 1200 x 1200 x 600 mm L x D x H 平台尺寸：1200 x 1200 x 600 mm L x D x H aluminium frame base 铝合金型材底座 Aluminium or sandwich compound desk plate with M8 thread holes in 100 x 100 mm grid 100 x 100 mm螺孔矩阵 4 lockable casters 4个可锁脚轮 wiring connection to the automatic chamber system to avoid chamber ope
30、ning when test table is attached without type specific adaptor for test specimen连接自动门环境箱的电缆，防止自动门意外开启 Test TablePage 9 / 202.0 HIGH SPEED IMAGERS 高速照相机 PHOTRON FASTCAM SA-3 MODEL 120 KC Color High-Speed-Camera with 1.024x1.024 pixels 17m pixel size CMOS-Sensor for frame rates from 2.000 fps at 1.024
31、 x 1.024 full resolution to max. 120.000 fps at reduced resolution 彩色，10241024 像速，CMOS 传感器，桢频高达 2000 桢/秒 分辨率高达 120000 - 1024x1024 Pixel 36-Bit CMOS-Sensor - very high light sensivity of app. 1.600 ISO /ASA - shutter times down to 2 s 1/500.00 - 1.000-Base-T-Gigabit-Ethernet - Trigger: Start Center E
32、nd Random variable Pre-Post Trigger TTL or mechanical switch rising or falling edge - Frame memory 2 GB - Shock resistant up to 100 G / 10 ms - Software: Photron File viewer PFV - 110/220V Power Supply - Size: 120 x 120 x 220 mm - Weight: 40 kg FASTCAM SA3 Model 120K 1024 X 1024 pixels 2000fps 768 x
33、 768 pixels 3000fps 512 x 512 pixels 6000fps 256 x 256 pixels 15000fps and at reduced resolution up to 120000fps2.1 MANUAL ZOOM LENS - F-Mount adaptation - Focal Length 24 - 70 mm F 2.8 手动调焦2.2 TRIPOD AND ACCESSORIES 2 pcs - Heavy duty tripod with pan and tilt head 支架和配件Page 10 / 203.0 HALOGEN PHOTO
34、 LIGHT SYSTEM卤素照明系统 1 SET3.1 LIGHT SYSTEM FOR INSIDE TEMPERATURE CHAMBER 20 KW 照明系统安装在环境箱内，20KW - light suspension system with total 20 halogen lights total power consumption approximately 20 kW 总计20个卤素灯共20KW - suspension frame / rail stem for halogen for mounting at the ceiling estimated ceiling he
35、ight 3.4 meter 灯光安装带离地高度3-4米的滑槽 - incl. 2 movable trolleys for 3 lights each 包含两个3灯头的移动推车 - professional heavy duty design 专业加固设计 - color temperature about 3200 K 3200K色温 - power consumption 1000 W / each 1000W/每个灯管 - supply voltage 230 V single phase 单向230V - metal cover 金属外壳 - safety screen 安全遮板 -
36、 cable length have to be specified by customer for final destination range 5 20 m 线缆长度由客户决定（5-20m） - incl. spare parts 包含备件 Picture shows similar arrangement 分布示意图3.2 LIGHT SWITCHING CABINET 灯光控制柜 -completely prepared for halogen light switching of: 完全为卤素灯光系统配置的开关系统 -lights groups of Halogen Light 2
37、0 kW for ambiente 1组20kW控制（环境试验） -incl. heavy duty connectors 包含加强连接头 Picture shows similar arrangement 示意图Page 11 / 204.0 AIRBAG STATIC DEPLOYMENT TEST SYSTEM 安全气囊静态点爆实验系统4.1 19quot- RACK IGNITION AND DATA ACQUISITION CONTROL SYSTEM 19quot点火和数据采集控制系统 -for the integration of the ignition and measuri
38、ng system INTERFACER 4 and the 19” control computer 整合了点火与测量系统并使用19”控制计算机 -lockable casters可锁脚轮 -electrical installation power supply main switch emergency and safety circuits 电气安装、电源、主开关及紧急安装装置 -heavy industrial plugs on the rear for external devices 为外部装置连接所预留的工业级加强型接头 equipped with following modu
39、les: 设备带以下模块安全气囊静态点爆控制和影像 安全气囊点火和数据采集4.2 INTERFACER 4 BASE SYSTEM 基础系统 INTERFACE4 -standard system height 7 units 461 mm depth 19quot-rack-version 标准系统，高 7 units 461mm 深，19 寸 -30 slot places for the IF plug-in cards on front- and backside 前后总计 30 个插卡口 -2 planes of slot places 2 排插卡口 -IEEE-488-interf
40、ace for the communication with the PC IEEE-488 接口用于连接电脑，重新输出 RELAY OUTPUT -16 relay channels 16 个延迟通道 -for functions 功能：Page 12 / 20 door lock 门锁 lighting system group 1 ON 照明灯组 1 lighting system group 2 ON 照明灯组 2 ventilationon/off switch function 排烟系统开关 incl. connector terminal IF421-K15 包括连接终端 IF421-K15 -output of status signals and chamber handshake DIGITAL INPUT 状态信号输出和温度箱手刹信号输入 -16 input channe.
