《(海洋油气专业外语ppt课件)C-Well-Control.ppt》由会员分享，可在线阅读，更多相关《(海洋油气专业外语ppt课件)C-Well-Control.ppt（19页珍藏版）》请在三一办公上搜索。
1、Unit 6 Well Control,DefinitionProcess and Equipment for kick detection and control,Well control,Well control refers to the control of downhole formation pressures penetrated by the well.There are three distinct well control levels that may occur during drilling operations.Primary control.Primary con
2、trol is given by maintaining the density of the drilling fluid such that hydrostatic pressure at all depths where formations are exposed exceeds formation pore pressures.Mud hydrostatic pressureformation pore pressure,Primary control,There are four main reasons,in general,why primary control might b
3、e lost during drilling operations:1.The well penetrates an overpressured zone with a higher formation pressure than mud hydrostatic.2.A weak downhole formation allows sufficient mud to leave the wellbore so that the level of mud in the annulus drops.3.Failure to fill the hole properly when pulling o
4、ut of the hole.4.Swabbing.If the drillstring is pulled up with sufficient speed,the reduction in pressure at the bottom can be enough to allow formation fluids to enter the well.,BOP stack,The primary function of the BOP is to form a rapid and reliable seal around the drillstring or across the empty
5、 hole(if no pipe is in the hole)to contain downhole pressures.There are currently two types of preventers available that allow this seal to be formed.Most BOPs contain at least one of each type as the different characteristics of each are useful for different operations.Annular preventer/bag type pr
6、eventerFixed pipe ramVariable bore pipe ramBlind-shear ramDetection equipmentPit-volume totalizerFlow indicator,Bag type preventer(annular preventer),Functions:Sealing on irregular shaped tubularsAllowing pipes move in or out of the well under pressure(stripping),Ram type preventer,Fixed pipe ram.Th
7、e seal is sized to fit one outside diameter only,Variable bore pipe ram,The seal element can accommodate a narrow range of diameters,for example 3-1/2 to 7.It can only seal on round pipe,not square or hexagonal shapes,Blind rams,Designed to seal on the open hole.Blind-shear rams have blades incorpor
8、ated that can cut through drillpipe(though not through drill collars or casing),BOP stack,a BOP stack would have at least one bag preventer and two ram preventers.BOP stacks for deeper wells might have up to four ram preventers and two Annular preventers.The ram preventers generally have a higher pr
9、essure rating and are always installed below the bag preventers.If only two ram preventers are used,the bottom set will normally be blind-shear rams and the upper set will be pipe rams.One reason for placing the blind rams on the bottom is that if the pipe rams leak,it is possible to close the blind
10、 rams below and safely open up the upper preventer to change the rams.,BOP control systems,A hydraulic control system is used to move BOP units using hydraulic fluid under pressure.,BOP control systems,1.A reserve hydraulic fluid tank holding fluid at atmospheric pressure.2.A set of bottles holding
11、fluid under high pressure(usually 3,000 psi)with pressurized nitrogen.3.A high pressure manifold connected to the bottle system.4.A low pressure manifold that contains fluid at the working pressure of the ram preventers(usually 1,500 psi).5.A pressure regulator that feeds fluid from the high pressur
12、e manifold to the low pressure manifold,which reduces the unregulated pressure to the working pressure.A set of valves attached to the low pressure manifold that can direct working pressure fluid to the rams(to open or to close them)and that directs exhaust fluid back to the reserve hydraulic fluid
13、tank.,BOP control systems,7.A valve that controls the opening and closing of the bag preventer.8.A pressure regulator that feeds fluid from the low pressure manifold to the bag preventer control valve.Bag preventers operate at a lower pressure than ram preventers,but as the seal element gets worn,hi
14、gher pressure is required to make the bag seal around the pipe.This regulator is also used to lower the closing pressure to the bag preventer if it is desired to strip pipe in through the preventer or to increase the closing pressure on a worn element.9.Two sets of pumps to maintain system pressure.
15、One set is driven by compressed air from the rig air system,the other is powered by electricity This provides some backup in the event of either the rigs air or electrical system failing.The air driven pumps give a higher flow rate and pressure the system to around 2,800 psi.The electric pump tops t
16、he system to the full pressure of 3,000 psi at a lower flow rate.,Kick Detection Equipment,1.The pit-volume totalizer provides a readout showing the total volume of drilling fluid held on the surface in the active system tanks.If this total increases,and if the increase is not due to the mud enginee
17、r adding chemicals or fresh mud to the system,then a kick is occurring.2.The flow indicator is an instrument attached to a paddle that sits in the flowline from the annulus.This paddle is pushed up by the returning mud stream-the amount it is pushed depends on the flow rate,among other things.If the
18、 flow rate should increase an alarm will sound.If the flow rate out increases,but the mud pump speed has not been increased,it is possible that the extra flow out is due to an influx entering the wellbore.Generally,the flow indicator will give the first positive indication of a kick.However,the padd
19、le type flow indicator is prone to false alarms because of cuttings and other debris that may stick to the paddle or build up underneath it.,Signs of a kick,Drilling breakMud pit gainFlowing wellShows of gas,oil or salt waterDecrease in circulating pressure(flow rate increase)Pump stroke increaseImp
20、roper hole fill-upString weight change(buoyancy effect decreases,and string becomes heavier),Killing the well,If the surface instruments indicate that a kick is in progress while drilling,normally the driller will stop drilling,pick up the drillstring so that the bit is above the bottom of the hole
21、and stop the pumps.A visual check is then made by looking down through the rotary table,into the bell nipple,at the level of mud in the annulus.If the well is in fact kicking,then the mud in the annulus will still be moving upwards even though the pumps are shut down.Having confirmed a kick,the dril
22、ler will close the BOP as quickly as possible and notify the toolpusher and drilling supervisor in charge of the rig.If the permeability of the flowing formation is high,the kick can develop very quickly.A larger drilled hole will also allow influx to flow in faster but this is compensated for(to an
23、 extent)because the capacity of the hole is greater in a larger hole.It is also possible that if permeability is very low,little or no influx enters the wellbore even though mud hydrostatic is less than the formation pore pressure.,Well control procedures,Shut well inPull kelly upOpen hydraulic closing ram(HCR)valve but not superchoke or choke manifold.Close annular preventerRecord pressureRecord shut-in drill pipe pressure(SIDPP)Record shut-in casing pressure(SICP).,Kill methods,Drillers methodWait-and-weight method(engineers method)Circulate and weight method,
