《某省电信汇聚交换机OLT双上行配置模板.doc》由会员分享，可在线阅读，更多相关《某省电信汇聚交换机OLT双上行配置模板.doc（26页珍藏版）》请在三一办公上搜索。
1、汇聚交换机OLT双上行配置模板V2华为S8505模式一：单链路+Smar-link1. 板卡硬件要求：要求板卡中带有“DB”字样并且软件版本在1267以上、或者没有“DB”字样软件版本在1628以上，可以支持灵活QinQ 。2. 软件版本要求：Release1600以上可以配Smart-link3. 配置命令 定义VLAN ACL acl number 4001 rule 0 permit ingress 51 to 1050 egress any /匹配普通宽带拨号用户VLAN rule 1 permit ingress 43 egress any /匹配iTV用户VLAN rule 2 p
2、ermit ingress 45 egress any /匹配ITMS终端管理VLAN 定义外层VLANvlan 501-502 901-902 1701-1702 smart-link配置stp region-configuration instance 1 vlan 501 901 1701instance 2 vlan 502 902 1702active region-configuration /每次更改配置后必须执行这条命令才生效smart-link group 1 preemption mode role /启用故障链路恢复后的自动倒换功能 protected-instance
3、1 undo flush enablesmart-link group 2 preemption mode role /启用故障链路恢复后的自动倒换功能 protected-instance 2 undo flush enableinterface GigabitEthernetX/X/X /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50为DSLAM管理VLAN port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 vlan filter di
4、sable traffic-redirect inbound link-group 4001 rule 0 system-index 1 nested-vlan 501 traffic-redirect inbound link-group 4001 rule 1 system-index 2 nested-vlan 1701 traffic-redirect inbound link-group 4001 rule 2 system-index 3 nested-vlan 901/system-index一般按顺序排列，只要不重复即可。interface GigabitEthernetX/X
5、/X /下行接口2 port link-type hybrid port hybrid vlan 50 tagged port hybrid vlan 502 902 1702 untagged undo port hybrid vlan 1 vlan filter disable traffic-redirect inbound link-group 4001 rule 0 system-index 4 nested-vlan 502 traffic-redirect inbound link-group 4001 rule 1 system-index 5 nested-vlan 1702
6、 traffic-redirect inbound link-group 4001 rule 2 system-index 6 nested-vlan 902interface GigabitEthernetX/X/X-01 /端口做为instance 1主用，instance 2备用port link-type trunk port trunk permit vlan 48 50 501-502 901-902 1701-1702 port smart-link group 1 masterport smart-link group 2 slaveinterface GigabitEther
7、netX/X/X-02 /端口做为instance 1备用，instance 2主用port link-type trunk port trunk permit vlan 49 501-502 901-902 1701-1702 port smart-link group 1 slave port smart-link group 2 master 双网管地址配置interface vlan 48 ip address A.B.C.2 255.255.255.252interface vlan 49 ip address A.B.C.6 255.255.255.252ip route 0.0.
8、0.0 0.0.0.0 A.B.C.1ip route 10.10.0.0.255.255.0.0 A.B.C.5 /10.10.0.0为网络管理服务器段4. 业务调试验证命令display smart-link group 1模式二：链路捆绑+Smart-link1. 板卡硬件要求：要求板卡中带有“DB”字样并且软件版本在1267以上、或者没有“DB”字样软件版本在1628以上，可以支持灵活QinQ 。2. 软件版本要求：Release1600以上可以配Smart-link3. 配置命令 定义VLAN ACL acl number 4001 rule 0 permit ingress 51
9、to 1050 egress any rule 1 permit ingress 43 egress any rule 2 permit ingress 45 egress any 定义外层VLANvlan 501 1701 901 定义链路组link-aggregation group 1 mode manuallink-aggregation group 2 mode manual smart-link配置stp region-configuration instance 1 vlan 501 901 1701active region-configuration /每次更改配置后必须执行
10、这条命令才生效smart-link group 1 preemption mode role /启用故障链路恢复后的自动倒换功能 protected-instance 1link-aggregation group 1 master /链路组1作为master link-aggregation group 2 slave /链路组2作为slaveundo flush enableinterface GigabitEthernetX/X/X /下行接口 port link-type hybrid port hybrid vlan 50 tagged port hybrid vlan 501 90
11、1 1701 untagged undo port hybrid vlan 1 vlan filter disable traffic-redirect inbound link-group 4001 rule 0 system-index 1 nested-vlan 501 traffic-redirect inbound link-group 4001 rule 1 system-index 2 nested-vlan 1701 traffic-redirect inbound link-group 4001 rule 2 system-index 3 nested-vlan 901/sy
12、stem-index一般按顺序排列，只要不重复即可。interface GigabitEthernetX/X/X-01 /主用上行口-1port link-type trunk port trunk permit vlan 48 50 501 901 1701 port link-aggregation group 1 /把端口加入link-aggregation group 1interface GigabitEthernetX/X/X-02 /主用上行口-2port link-type trunk port trunk permit vlan 48 50 501 901 1701 port
13、 link-aggregation group 1 /把端口加入link-aggregation group 1interface GigabitEthernetX/X/X-03 /备用上行口-1port link-type trunk port trunk permit vlan 49-50 501 901 1701 port link-aggregation group 2 /把端口加入link-aggregation group 2interface GigabitEthernetX/X/X-04 /备用上行口-2port link-type trunk port trunk permi
14、t vlan 49-50 501 901 1701 port link-aggregation group 2 /把端口加入link-aggregation group 2 双网管地址配置interface vlan 48 ip address A.B.C.2 255.255.255.252interface vlan 49 ip address A.B.C.6 255.255.255.252ip route 0.0.0.0 0.0.0.0 A.B.C.1ip route 10.10.0.0.255.255.0.0 A.B.C.5 /10.10.0.0为网络管理服务器段4. 业务调试验证命令d
15、isplay smart-link group 1display link-aggregation verbose模式三：单链路/链路捆绑+VLAN双向透传1. 板卡硬件要求：要求板卡中带有“DB”字样并且软件版本在1267以上、或者没有“DB”字样软件版本在1628以上，可以支持灵活QinQ。2. 软件版本要求：无特殊要求3. 配置命令 定义VLAN ACL acl number 4001 rule 0 permit ingress 51 to 1050 egress any rule 1 permit ingress 43 egress any rule 2 permit ingress
16、45 egress any 定义外层VLANvlan 501 1701 901 VLAN双向透传配置interface GigabitEthernetX/X/X /下行接口 port link-type hybrid port hybrid vlan 50 tagged port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 vlan filter disable traffic-redirect inbound link-group 4001 rule 0 system-index 1 nested-vlan 501 tr
17、affic-redirect inbound link-group 4001 rule 1 system-index 2 nested-vlan 1701 traffic-redirect inbound link-group 4001 rule 2 system-index 3 nested-vlan 901/system-index一般按顺序排列，只要不重复即可。interface GigabitEthernetX/X/X-01 /上行口1port link-type trunk port trunk permit vlan 48 50 501 901 1701interface Giga
18、bitEthernetX/X/X-02 /上行口2port link-type trunk port trunk permit vlan 49 501 901 1701 双网管地址配置interface vlan 48 ip address A.B.C.2 255.255.255.252interface vlan 49 ip address A.B.C.6 255.255.255.252ip route 0.0.0.0 0.0.0.0 A.B.C.1ip route 10.10.0.0.255.255.0.0 A.B.C.5 /10.10.0.0为网络管理服务器段4. 业务调试验证命令dis
19、play vlan X/X/X华为S9300模式一：单链路+Smar-link 灵活QINQ配置：（S9300主机版本为V100R001版本或业务单板类型最后一个字母为A的单板使用如下流策略配置灵活QINQ）1、 定义内层VLAN的流策略： traffic classifier QINQA-1if-match vlan-id 51 to 1050 /匹配普通宽带拨号用户VLANtraffic classifier QINQA-2if-match vlan-id 43 /匹配iTV用户VLANtraffic classifier QINQA-3if-match vlan-id 45 /匹配ITM
20、S终端管理VLAN#traffic behavior QINQA-1nest top-most vlan-id 501 /外层VLANtraffic behavior QINQA-2nest top-most vlan-id 901 /外层VLANtraffic behavior QINQA-3nest top-most vlan-id 1701 /外层VLAN#traffic behavior QINQB-1nest top-most vlan-id 502 /外层VLANtraffic behavior QINQB-2nest top-most vlan-id 902 /外层VLANtra
21、ffic behavior QINQB-3nest top-most vlan-id 1702 /外层VLAN#traffic policy QINQAclassifier QINQA-1 behavior QINQA-1classifier QINQA-2 behavior QINQA-2classifier QINQA-3 behavior QINQA-3traffic policy QINQBclassifier QINQA-1 behavior QINQB-1classifier QINQA-2 behavior QINQB-2classifier QINQA-3 behavior Q
22、INQB-32、 定义外层VLANvlan batch 501 502 901 902 1701 17023、 接口配置interface GigabitEthernetX/X/X /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50为DSLAM管理VLAN port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 traffic-policy QINQA inbound#interface GigabitEthernetX/X/X /下行接口1 po
23、rt link-type hybrid port hybrid vlan 50 tagged /VLAN 50为DSLAM管理VLAN port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1 traffic-policy QINQB inbound# 灵活QINQ配置：（S9300主机版本为V100R002版本或业务单板最后一个字母非A的单板使用如下STACKING配置灵活QINQ）1、 定义外层VLANvlan batch 501 502 901 902 1701 17022、接口配置interface GigabitEt
24、hernetX/X/X /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50为DSLAM管理VLAN port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 port vlan-stacking vlan 51 to 1050 stack-vlan 501port vlan-stacking vlan 43 stack-vlan 901port vlan-stacking vlan 45 stack-vlan 1701#interface Gigab
25、itEthernetX/X/X /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50为DSLAM管理VLAN port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1port vlan-stacking vlan 51 to 1050 stack-vlan 502port vlan-stacking vlan 43 stack-vlan 902port vlan-stacking vlan 45 stack-vlan 1702# smart-link配
26、置stp region-configuration instance 1 vlan 501 901 1701instance 2 vlan 502 902 1702active region-configuration /每次更改配置后必须执行这条命令才生效smart-link group 1protected-vlan reference-instance 1 restore enable /启用故障链路恢复后的自动倒换功能 smart-link enable port GigabitEthernet1/0/1 masterport GigabitEthernet1/0/2 slave ti
27、mer wtr 30 /配置主端口恢复30s后恢复smart-link group 2protected-vlan reference-instance 1 restore enable /启用故障链路恢复后的自动倒换功能 smart-link enable port GigabitEthernet1/0/2 masterport GigabitEthernet1/0/1 slavetimer wtr 30 /配置主端口恢复30s后恢复#interface GigabitEthernet1/0/1 /端口做为instance 1主用，instance 2备用port link-type tru
28、nk port trunk permit vlan 48 50 501-502 901-902 1701-1702#interface GigabitEthernet1/0/2 /端口做为instance 1备用，instance 2主用port link-type trunk port trunk permit vlan 49 501-502 901-902 1701-1702 双网管地址配置interface vlan 48 ip address A.B.C.2 255.255.255.252interface vlan 49 ip address A.B.C.6 255.255.255.
29、252ip route 0.0.0.0 0.0.0.0 A.B.C.1ip route 10.10.0.0.255.255.0.0 A.B.C.5 /10.10.0.0为网络管理服务器段 业务调试验证命令display smart-link group 1模式二：链路捆绑+Smart-link 灵活QINQ配置：（S9300主机版本为V100R001版本或业务单板类型最后一个字母为A的单板使用如下流策略配置灵活QINQ）1、 定义内层VLAN的流策略： traffic classifier QINQA-1if-match vlan-id 51 to 1050 /匹配普通宽带拨号用户VLANtr
30、affic classifier QINQA-2if-match vlan-id 43 /匹配iTV用户VLANtraffic classifier QINQA-3if-match vlan-id 45 /匹配ITMS终端管理VLAN#traffic behavior QINQA-1nest top-most vlan-id 501 /外层VLANtraffic behavior QINQA-2nest top-most vlan-id 901 /外层VLANtraffic behavior QINQA-3nest top-most vlan-id 1701 /外层VLAN#traffic b
31、ehavior QINQB-1nest top-most vlan-id 502 /外层VLANtraffic behavior QINQB-2nest top-most vlan-id 902 /外层VLANtraffic behavior QINQB-3nest top-most vlan-id 1702 /外层VLAN#traffic policy QINQAclassifier QINQA-1 behavior QINQA-1classifier QINQA-2 behavior QINQA-2classifier QINQA-3 behavior QINQA-3traffic pol
32、icy QINQBclassifier QINQA-1 behavior QINQB-1classifier QINQA-2 behavior QINQB-2classifier QINQA-3 behavior QINQB-32、 定义外层VLANvlan batch 501 502 901 902 1701 17023、 接口配置interface GigabitEthernetX/X/X /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50为DSLAM管理VLAN port hybrid vlan 501 901
33、 1701 untagged undo port hybrid vlan 1 traffic-policy QINQA inbound#interface GigabitEthernetX/X/X /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50为DSLAM管理VLAN port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1 traffic-policy QINQB inbound# 灵活QINQ配置：（S9300主机版本为V100R002版本或
34、业务单板最后一个字母非A的单板使用如下STACKING配置灵活QINQ）1、 定义外层VLANvlan batch 501 502 901 902 1701 17022、接口配置interface GigabitEthernetX/X/X /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50为DSLAM管理VLAN port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 port vlan-stacking vlan 51 to 1050 stack
35、-vlan 501port vlan-stacking vlan 43 stack-vlan 901port vlan-stacking vlan 45 stack-vlan 1701#interface GigabitEthernetX/X/X /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50为DSLAM管理VLAN port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1port vlan-stacking vlan 51 to 1050 st
36、ack-vlan 502port vlan-stacking vlan 43 stack-vlan 902port vlan-stacking vlan 45 stack-vlan 1702# smart-link配置stp region-configuration instance 1 vlan 501 901 1701instance 2 vlan 502 902 1702active region-configuration /每次更改配置后必须执行这条命令才生效smart-link group 1protected-vlan reference-instance 1 restore e
37、nable /启用故障链路恢复后的自动倒换功能 smart-link enable port Eth-Trunk1 masterport Eth-Trunk2 slave timer wtr 30 /配置主端口恢复30s后恢复smart-link group 2protected-vlan reference-instance 1 restore enable /启用故障链路恢复后的自动倒换功能 smart-link enable port Eth-Trunk2 masterport Eth-Trunk1 slavetimer wtr 30 /配置主端口恢复30s后恢复#interface G
38、igabitEthernetX/X/X-01 /主用上行口-1Eth-Trunk1 /把端口加入link-aggregation group 1interface GigabitEthernetX/X/X-02 /主用上行口-2Eth-Trunk1 /把端口加入link-aggregation group 1interface GigabitEthernetX/X/X-03 /备用上行口-1Eth-Trunk2 /把端口加入link-aggregation group 2interface GigabitEthernetX/X/X-04 /备用上行口-2Eth-Trunk2 /把端口加入lin
39、k-aggregation group 2interface Eth-Trunk1 /端口做为instance 1主用，instance 2备用port link-type trunk port trunk permit vlan 48 50 501-502 901-902 1701-1702#interface Eth-Trunk2 /端口做为instance 1备用，instance 2主用port link-type trunk port trunk permit vlan 49 501-502 901-902 1701-1702 双网管地址配置interface vlan 48 ip
40、address A.B.C.2 255.255.255.252interface vlan 49 ip address A.B.C.6 255.255.255.252ip route 0.0.0.0 0.0.0.0 A.B.C.1ip route 10.10.0.0.255.255.0.0 A.B.C.5 /10.10.0.0为网络管理服务器段 业务调试验证命令display smart-link group 1display link-aggregation verbose模式三：单链路/链路捆绑+VLAN双向透传 灵活QINQ配置：（S9300主机版本为V100R001版本或业务单板类型最
41、后一个字母为A的单板使用如下流策略配置灵活QINQ）1、 定义内层VLAN的流策略： traffic classifier QINQA-1if-match vlan-id 51 to 1050 /匹配普通宽带拨号用户VLANtraffic classifier QINQA-2if-match vlan-id 43 /匹配iTV用户VLANtraffic classifier QINQA-3if-match vlan-id 45 /匹配ITMS终端管理VLAN#traffic behavior QINQA-1nest top-most vlan-id 501 /外层VLANtraffic beh
42、avior QINQA-2nest top-most vlan-id 901 /外层VLANtraffic behavior QINQA-3nest top-most vlan-id 1701 /外层VLAN#traffic behavior QINQB-1nest top-most vlan-id 502 /外层VLANtraffic behavior QINQB-2nest top-most vlan-id 902 /外层VLANtraffic behavior QINQB-3nest top-most vlan-id 1702 /外层VLAN#traffic policy QINQAcl
43、assifier QINQA-1 behavior QINQA-1classifier QINQA-2 behavior QINQA-2classifier QINQA-3 behavior QINQA-3traffic policy QINQBclassifier QINQA-1 behavior QINQB-1classifier QINQA-2 behavior QINQB-2classifier QINQA-3 behavior QINQB-32、 定义外层VLANvlan batch 501 502 901 902 1701 17023、 接口配置interface GigabitEthernetX/X/X /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /VLAN 50为DSLAM管理VLAN port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 traffic-policy QINQA inbound#interface GigabitEthernetX/X/X /下行接口1 port link-type hybrid port
