《无线电能传输技术.doc》由会员分享，可在线阅读，更多相关《无线电能传输技术.doc（10页珍藏版）》请在三一办公上搜索。
1、所谓无线电能传输，就是借助于电磁场或电磁波进行能量传递的一种技术。无线输电分为：电磁感应式、电磁共振式和电磁辐射式。电磁感应可用于低功率、近距离传输；电磁共振适于中等功率、中等距离传输；电磁辐射则可用于大功率、远距离传输。近年来，一些便携式电器如笔记本电脑、手机、音乐播放器等移动设备都需要电池和充电。电源电线频繁地拔插，既不安全，也容易磨损。一些充电器、电线、插座标准也并不完全统一，这样即造成了浪费，也形成了对环境的污染。而在特殊场合下，譬如矿井和石油开采中，传统输电方式在安全上存在隐患。孤立的岛屿、工作于山头的基站，很困难采用架设电线的传统配电方式。在上述情形下，无线输电便愈发显得重要和迫切
2、，因而它被美国技术评论杂志评选为未来十大科研方向之一。在此旨在阐述当前的技术进展，分析无线输电原理。1 无线电能传输技术的发展历程最早产生无线输能设想的是尼古拉特斯拉(Nikola Tesla)，因而有人称之为无线电能传输之父。1890年，特斯拉就做了无线电能传输试验。特斯拉构想的无线电能传输方法是把地球作为内导体，把地球电离层作为外导体，通过放大发射机以径向电磁波振荡模式，在地球与电离层之间建立起大约8 Hz的低频共振，利用环绕地球的表面电磁波来传输能量。最终因财力不足，特斯拉的大胆构想没能实现 。其后，古博(Goubau)、施瓦固(Sohweing)等人从理论上推算了自由空间波束导波可达到
3、近100的传输效率，并随后在反射波束导波系统上得到了验证。20世纪20年代中期，日本的H.Yagi和S.Uda发明了可用于无线电能传输的定向天线，又称为八木一宇田天线。20世纪60年代初期雷声公司(Raytheon)的布朗(W.C.Brown)做了大量的无线电能传输研究工作，从而奠定了无线电能传输的实验基础，使这一概念变成了现实。在实验中设计了一种效率高、结构简单的半波电偶极子半导体二极管整流天线，将频率2.45GHz的微波能量转换为了直流电。1977年在实验中使用GaAsPt肖特基势垒二极管，用铝条构造半波电偶极子和传输线，输入微波的功率为8 W，获得了90.6的微波直流电整流效率。后来改用
4、印刷薄膜，在频率2.45 GHz时效率达到了85。自从Brown实验获得成功以后，人们开始对无线电能传输技术产生了兴趣。1975年，在美国宇航局的支持下，开始了无线电能传输地面实验的5 a计划。喷气发动机实验室和Lewis科研中心曾将30 kW的微波无线输送1.6 km，微波直流的转换效率达83。1991年，华盛顿ARCO电力技术公司使用频率35 GHz的毫米波，整流天线的转换效率为72。1998年，5.8 GHz印刷电偶极子整流天线阵转换效率为82。前苏联在无线电能传输方面也进行了大量的研究。莫斯科大学与微波公司合作，研制出了一系列无线电能传输器件，其中包括无线电能传输的关键器件快回旋电子束
5、波微波整流器 。近几年，无线电能传输发展更是迅速。Wildcharge、Powercast、SplashPower、东京大学，相继开发出非接触式充电器。MIT在2007年6月宣布，利用电磁共振成功地点亮了一个离电源约2 m远的60 w电灯泡，这项技术被称为WiTricity。该研究小组在实验中使用了两个直径为50 cm的铜线圈，通过调整发射频率使两个线圈在10MHz产生共振，从而成功点亮了距离电力发射端2 m以外的一盏60 w灯泡。2 无线电能传输的原理（1）非接触电能传输系统利用疏松感应耦合系统和电力电子技术相结合的方法，实现了电能的无物理连接传输。它将系统的变压器紧密型耦合磁路分开，初、次
6、级绕组分别绕在具有不同磁性的结构上，实现在电源和负载单元之间进行能量传递而不需物理连接。其一次侧、二次侧之间通过电磁感应实现电能传输，因气隙导致的耦合系数的降低由提高一次侧输入电源的频率加以补偿。理论和经验都表明：当原边电流频率、幅值越高，原、副边距离越小，与空气相比，磁心周围介质的相对磁导率越大时，可分离式变压器的传输效率越高。但实际应用当中原副边距离不可能无限小，必须对原副边采取相应的补偿措施，这种无线电能传输效率较低。（2）对无线电能传输来说，能量传递的效率是最重要的。因此，方向性强、能量集中的激光与具有类似性质的微波束是值得考虑的选择。但激光光束在空间传输易受到空气和尘埃的散射，非线性
7、效应明显，且输出功率小，因此微波输能成为首选。微波输能，就是将微波聚焦后定向发射出去，在接收端通过整流天线(rectenna)把接收到的微波能量转化为直流电能。布朗的微波输电系统。上世纪60年代，William C.Brown向世人展示的微波传输电能示意图。该微波传输系统包括微波源、发射天线、接受天线3部分。微波源内有磁控管，能控制源在245 GHz频段输出5200 W的功率；微波源输出的能量通过同轴电缆连接至和波导管之间的适配器上；亚铁酸盐的循环器连接在波导管上，使波导管和发射天线相匹配。发射天线包含8个部分，每个部分上都有8个缝隙。这64个缝隙均匀的向外发射电磁波。这种开孔的波导天线很适合
8、用于无线电能传输，因为它有高达95%的孔径效率和很高的能量捕捉能力。硅控整流二极管天线用来收集微波并把它转换成直流电，在布朗展示的系统中该接收天线拥有25%的收集和转换效率，这种天线在2.45GHz测试时曾经达到甚至超过90%的效率。传输距离较远之后，增强天线的方向性和效率会十分困难。微波输能的传输效率。若D代表微波在自由空间传输的距离， 、 分别代表发射天线和接收天线的面积，入表示工作波长，则微波在自由空间的传输效率n是参数的函数。由公式知传输效率和传输距离没有直接的联系，而是由决定。故距离D增大的效应V可由 、 的增加或入的减小来补偿。微波输能的总效率等于直流到微波、微波传输和接收整流三部
9、分效率之积。故可知当前微波传输能量的效率还不高，但是还是很有发展潜力的。（3）辐射性传输，虽然完全适合于传输信息，但是将其应用于电能传输却会引起很多的困难：如果辐射是全方向性的，则电能传输效率会十分的低；如果是定向辐射，也要求具有不间断可视的方位和十分复杂的追踪仪器设备，而磁谐振却没有这么复杂。自谐振线圈的模型描述。A是一个半径为25 cm的单匝铜环，它是激励电路的一部分，输出频率为9.9 MHz的正弦波。S和D是自谐振线圈。B是连接到负载(灯泡)的单匝导线环。不同的K代表箭头表示的对象之间的直接耦合。调整线圈D和A之间的角度，保证它们之间的直接耦合等于零。线圈S和D同轴排列。线圈B和A以及B
10、和s的直接耦合是可以忽略不计的。强耦合磁谐振下的电能传输效率。在 耦合谐振系统(如声音、电磁、磁、核等)里，经常 会产生“强耦合”运行状态。如果处于给定系统中的这种状态，谐振体之间的能量交换则可期望达到很高的效率。如果不考虑周围空间的结构，并且在干涉损耗和散失在周围环境中的损耗很低时，中等距离的能量传输用这种方法可以在接近全方向的状态下实现并达到很高的效率。3 结束语一些边远山区、牧区、高原、海岛，人口稀少，居住分散，交通不便，经济落后，那儿缺乏常规能源，又远离大电网，严重影响当地经济发展。这种情况下，利用微波输能技术，可以解决电网的死角。输电工程最关心的是效率和经济性。无线电能传输的效率取决
11、于微波源的效率、发射接收天线的效率和微波整流器的效率；其经济性如何，依赖于所用频段的微波元器件的价格与有线输电系统所用器材价格的比较，也与具体的输电网络的参数有关系。除了关心经济和效率以外，还要对大功率微波对环境和身体健康可能造成的影响进行研究，需保证如下方面：（1）传输微波能流密度不能对电离层产生明显扰动；（2）必须保证不干扰Et常通信；（3）地面整流接收站不能对飞机等交通工具及周围的生物体（如鸟类、居民等）产生不良作用。 来自：科学技术附英文原文：Wireless Transmission Techniques The so-called radio transmission techno
12、logy is an energy transfer technique by means of electromagnetic fields or electromagnetic wave. The wireless transmission is divided into: electromagnetic induction-type, electric type and magnetic resonance electromagnetic radiation type. Electromagnetic induction can be used for low-power, short
13、distance transmission; electric magnetic resonance is suitable for medium-power, medium-distance transmission; electromagnetic radiation can be used for high-power, long-distance transmission. In recent years, a number of portable electrical appliances such as notebook computers, mobile phones, musi
14、c players and other mobile devices will need batteries and charger. Power cable plug frequently, that is neither safe, nor easy to wear and tear. Some chargers, cables, socket standards are not entirely unified.That would result in a waste and environmental pollution. And in special occasions, such
15、as mining and oil exploration, the traditional transmission approach in terms of security risks exist. Isolated islands, the work of the hills of the base station, it is difficult to set up cables using the traditional distribution methods. In these cases, the wireless transmission will be increasin
16、gly more important and urgent, so it is the United States, Technology Review magazine top ten for the future research directions. In wireless transmission areas, our research has only just started, compared with Europe and the United States lagging behind. This sets out the current technological pro
17、gress, analyze the wireless transmission principles.1 The development process of radio transmission technologyProduce the first wireless transmission can be envisaged is Nikola Tesla (Nikola Tesla), which was known as the father of the radio can transmit. In 1890, Tesla made a radio is able to carry
18、 on the experiment. Tesla idea of radio transmission method is to be able to, within the earth as a conductor, the Earths ionosphere as the outer conductor, through the amplification of electromagnetic waves transmitter to the radial oscillation mode, set up between the Earth and ionosphere of about
19、 8 Hz low-frequency resonance the use of electromagnetic waves around the Earths surface to transmit the energy. The end of insufficient financial resources, Tesla failed to achieve a bold vision.Subsequently, the Goubau, Sohweing, who calculated the theoretical free-space beam guided wave can reach
20、 nearly 100% transmission efficiency, and subsequently reflected beam waveguide system has been verified. 20 mid-20th century, Japans H. Yagi, and S. Uda invention can be used to transmit radio directional antenna, also known as a Yagi Uda antenna. 60 in the early 20th century, Raytheon Company , w.
21、C.Brown have done a lot of radio is able to carry research work, which laid the foundation of radio transmission experiments can be the basis to make this concept become a reality.In the experiment designed a high efficiency, simple structure, the half-wave rectifier diode electric dipole antenna, t
22、he frequency of 2.45GHz microwave energy conversion to DC. 1977, used in experiments GaAs-Pt Schottky barrier diode, constructed of aluminum half-wave electric dipole and transmission lines, input microwave power of 8 W, won 90.6% of the microwave - the efficiency of DC rectifier . Then use print fi
23、lm, in the frequency of 2.45 GHz when the efficiency reaches 85%.Since the Brown experiment a success, people began to radio transmission technology can produce interest. In 1975, NASAs support, began a radio transmission on the ground can experiment 5 a plan. Jet Engine Laboratory and Lewis Researc
24、h Center who will be 30 kW of microwave radio transmission 1.6 km, microwave - DC conversion efficiency of up to 83%. In 1991, Washington, ARCO Power Technologies, Inc. 35 GHz millimeter-wave frequency, the conversion efficiency of rectenna 72%. In 1998, 5.8 GHz printed dipole rectenna array convers
25、ion efficiency is 82%.Radio is able to carry the former Soviet Union also carried out a lot of research. Moscow State University and microwave companies, developed a series of radio is able to carry devices, including radio can transmit a key device - fast cyclotron wave of e-beam microwave rectifie
26、rs.In recent years, radio is able to carry the development of even more rapid. Wildcharge, Powercast, SplashPower, University of Tokyo have developed a non-contact type charger. MIT in June 2007, announced the successful use of electric magnetic resonance of a place of light from the power supply of
27、 about 2 m away 60 w light bulb, the technology is known as WiTricity. The research team in experiments using two 50 cm diameter copper coils, by adjusting the transmission frequency to the two coils resonate at 10 MHz, thus successfully lit the distance 2 m away from the transmitter power of a 60 w
28、 bulb .待添加的隐藏文字内容32 The pirnciple of radio transmission（1）Non-contact power transmission system, the use of loose coupling system and power electronic induction method of combining technologies to achieve the non-physical connection of the power transmission. It will compact the system transformer-c
29、oupled magnetic circuit to separate the primary and secondary windings, respectively around with different magnetic structure, achieve the power and energy transfer between the load cell without the need for physical connection. Its primary side and secondary side through electromagnetic induction b
30、etween the realization of power transmission and coupling coefficients due to air gap caused by the reduction by an increase in the frequency of one side to compensate for input power. Theory and experience indicate that: When the primary side current frequency, amplitude of the higher of both sides
31、 of the smaller distance, and the air compared to the surrounding medium core relative permeability greater when the detachable transformer transfer efficiency more high. However, when the Central Plains of both sides of the practical application of the distance can not be infinitely small, former d
32、eputy side must take appropriate compensatory measures, which the radio is able to carry less efficient.（2）On the radio can transmit, the energy transfer efficiency is the most important. Therefore, the orientation strong energy concentration in laser and microwave beams of a similar nature is worth
33、 considering options. However, in the space laser beam transmission vulnerable to air and dust scattering, nonlinear effects are more obvious, and the output power is small, so can become the first choice of microwave transmission. Microwave input energy, that is, after the directional microwave foc
34、using launched, at the receiving end through the rectifier antenna (rect-enna) the received microwave energy into DC can be.Browns microwave transmission system. The last century, 60 years, William C. Brown to show the world the microwave transmission power diagram. The microwave transmission system
35、, including microwave source, transmitting antenna, receiving antenna part 3. There are magnetron microwave source can control the source in the 2.45 GHz frequency band output of 5 200 W of power; microwave source output power through the coaxial cable connected to and between the waveguide adapter;
36、 Ferrous Salts loop device connected to the waveguide, the waveguide tube and the transmitting antenna to match. Transmitting antenna contains eight parts, each part of the gap on both 8. This is a uniform gap of 64 out emit electromagnetic wave.Such openings waveguide antenna can be very suitable f
37、or radio transmission, because it has up to 95% of the aperture efficiency and high energy capture capabilities. Silicon-controlled rectifier diode microwave antennas used for the collection and put it into DC, Brown demonstrated that the receiving antenna system has a 25% collection and conversion
38、efficiency, this antenna has 2.45GHz tested to meet or exceed 90% efficiency . After the transmission distance and enhance the antenna directivity and efficiency will be very difficult.Microwave transmission energy transmission efficiency. If the D on behalf of microwave transmission distance in fre
39、e space, 、 representing the transmitting antenna and receiving antenna area, into the said operating wavelength, then the microwave in free space transmission efficiency n is the parameter function.By a formula known transmission efficiency and transmission distance is no direct link, but by the dec
40、ision. Therefore, the distance D increases the effect of V can be 、 of the increase or the decrease of income to compensate. The overall efficiency of microwave energy input is equal to DC to microwave, microwave transmission and reception efficiency rectifier three-part product. Therefore, we can s
41、ee the current microwave transmission of energy efficiency is not high, but it is still great potential for development.（3）Radiative transfer, though perfectly suited to transmit information, but it will be applied to energy transfer but it will give rise to many problems: If the radiation is a full
42、-directional, then the energy transfer efficiency will be very low; if it is directional radiation, but also requires a continuous visual orientation and very complex tracking equipment, and magnetic resonance but not so complicated.Self-resonant coil model description. A is a radius of 25 cm single
43、-turn copper ring, which is to stimulate a part of the circuit, the output frequency of 9.9 MHz sine wave. S and D is a self-resonant coils. B is connected to the load (light bulbs) in a single turn wire loop. Representative of the different K-arrows direct coupling between the objects. Adjust the c
44、oil the angle between D and A to ensure that the direct coupling between them is zero. S and D coaxial coil arrangement. Coil B and A and B, s, the direct coupling is negligible.Under the strong-coupling magnetic resonance energy transfer efficiency. In the coupled resonant systems (such as sound, e
45、lectromagnetic, magnetic, nuclear, etc.), the often have a strong coupling operation status. If you are in a given system in this state, resonance energy exchange between the body can be expected to achieve high efficiency. If you do not take into account the structure of the surrounding space, and
46、interfering loss and dissipation loss in the surrounding environment is low, medium-distance power transmission using this method can be close to the direction of a state-wide implementation and achieve high efficiency.3 ConclusionSome of the remote mountainous areas, pastoral areas, highlands, isla
47、nds, sparsely populated, scattered habitations, inconvenient transportation, economic backwardness, where the lack of conventional energy, but also away from the large power grids, a serious impact on the local economic development. This case, the use of microwave transmission energy technologies ca
48、n solve the grid corners. Transmission Project is most concerned about the efficiency and economy. The efficiency of the radio can transmit microwave source depends on the efficiency of transmit / receive antenna efficiency and the efficiency of microwave rectifiers; its economy to rely on the compo
49、nents used in the price band of microwave transmission systems and cable equipment for the price comparison, but also with specific parameters of the transmission network are related.Concerning the economy and efficiency, but also for high-power microwave on the environment and the possible impact of health research, it is need to ensure the following aspects: (1) transmission of microwave ener
