《西子奥的斯FOVF.ppt》由会员分享，可在线阅读，更多相关《西子奥的斯FOVF.ppt（19页珍藏版）》请在三一办公上搜索。
1、FOVF Control System Introduction OH-CON4421 System,XOEC2006-3,OH-CON4421:elevator use LCBII,AMCB2,SIEI drive and gear machine,Meaning of controller name,System introduce,LCBII,Setting of LCBII installation parameters of OH-CON4421 system is similar to MCS220M system|LSVF-W drive modelM1-3-1-4Drive:1
2、7 if ADO,set to 16Two sensors for DZ signalM1-3-1-6DZ-TYP:1The distance of two sensors is about 60mm,and the length of vane is 250mm,LCBII Parameters Setting,LSVF_W:DS Codes,The AMCB2 sent the DS(drive status)code to LCBII,the signals for LSVF-W are coded as described below:,LSVF_W：V codes,LCBII sen
3、t the V codes to AMCB2,which decide to run mode of drive.The signals described is followed:,SIEI Drive,Drive and Motor data setting,Take the 13VTR(14kw)machine as example.After the power on,double check the Drive data and motor data:TARTUP/Startup config/Setup mode/Drive data and Motor dataUsually s
4、et the Spd ref/fbk res to 0.125rpm。,Mechanical and Encoder data setting,the mechanical data decide the speed of elevator.The elevator use 1024 ppr,812Vdc encode,so set the Encoders config according to the chartAfter finishing the setting,you must save(Save config),Motor Autotune,The drive can carry
5、out the motor autotune without opening the brakeBefore motor autotune,the contactor must be active,and enable signal of drive must be active(connect the terminal 12 to 19 of drive),Complete stillStart？,Complete stillPress I key,SETUP MODEAutotune,Enter the menu and press Enter key twice,Press the I
6、key to start,Motor Autotune,Autotune begin,in this process,the keypad will display the rate of finished,Load setupYes-Ent No-Esc,STARTUPSave config？,When finished the autotune,press key,the keypad will display:,Press the Enter key,then press the key twice,After finished the autotune,press the Enter
7、key to save the autotune parameters,AMCB2 interface board,The function is similar to MCB of MCS220M controller It is a interface board between LCBII and SIEI drive.It receive the common form LCBII,then out put the speed curve to drive Before the normal run,the hoistway Self-study must have been done
8、,AMCB2,AMCB2 have 5 keys located below the display:,enter:back:shift P and F menu:add the parameters value:reduce the parameters valueEnter：enter the F menu;conform the modification,Keys of AMCB2,Terminals of AMCB2,Before the hoistway Self-study,you must conform the following items：Finished the moto
9、r autotune,conform all connect wire use for autotune have removed the short wiringParameters of drive and AMCB2 have finished settingthe elevator can run in inspection modeEnter to the F menu of amcb2,and set the F24 to 0.the parameter only allow the elevator to inspection and learn run,Hoistway Sel
10、f-study,Hoistway Self-study,switch the ERO to normal,set the parameter F0 of AMCB2 to 0,then press the Enter key to startThe car run down to bottom floor with low speed,then run up till the top floor to finish the hoistway Self-studyAfter hoistway self-study,the parameter F24 of AMCB2 will set to 1 automaticallyYou can get the self-study parameter form AMCB2:P1P32:floor distanceP34P35:1LS and 2LS distanceP36:length of vaneP37:the distance of two sensors,Any question,
