《模具设计与制造专业英语第2版.ppt》由会员分享，可在线阅读，更多相关《模具设计与制造专业英语第2版.ppt（32页珍藏版）》请在三一办公上搜索。
1、书名：模具设计与制造专业英语 第2版 ISBN：978-7-111-08537-9作者：王晓江出版社：机械工业出版社本书配有电子课件,模具设计与制造专业英语 第2版 ppt 课件,Unit one Lesson2 Heat Treatment of Tool Steels,教学目标及要求 1.掌握课文中有关热处理方面的专业词汇和专业术语；2.结合热处理的相关专业知识阅读课文，提高翻译能力。重点 1.有关热处理的专业词汇和专业术语；2.翻译课文：热处理的原理;热处理的类型;热处理的步骤。难句分析及翻译的基础知识 Part（）翻译的基础知识简介 二、翻译的标准,模具设计与制造专业英语 第2版 pp
2、t 课件,教学思路设计 时间分配（共100min）：1.讲解课文中的专业词汇和术语；2.讲解课后生词、大声朗读；3.翻译课文，注意穿插相关专业知识；4.分析难点句型，讲解相关翻译基础知识；5.学生答疑。,模具设计与制造专业英语 第2版 ppt 课件,Contents,Background KnowledgeNew Words and PhrasedText AnalysisQuestionsGlossary of TermsLanguage Points&Translating TechniquesReading Materials Summary References,模具设计与制造专业英语
3、 第2版 ppt 课件,The Principles of Heat Treatment,Heat treatment consists of Heating-Up and Cooling-Down process.Heating up the steel will change the microstructure to Austenite.Cooling down the steel at different cooling rates will change the microstructure from Austenite to different structures corresp
4、ondingly.Change in Microstructures result in change in mechanical properties.,Background Knowledge,模具设计与制造专业英语 第2版 ppt 课件,By heat treatment,we can change the mechanical properties of moulds and machine components to our desired state.For example,to harden the mould will increase strength and wear re
5、sistance resulting in longer mould life.To anneal a hard steel bar will soften it to a state good for machining.To normalize a steel bar will toughen it to a state good for impact.,模具设计与制造专业英语 第2版 ppt 课件,New Words and Expressions,Terms：1.Heat treating 热处理 normalize 正火 spheroidiz 球化处理 anneal 退火 harde
6、n 淬火 temper 回火 case harden 表面淬火 stress relieving 应力消除热处理 carburize 渗碳 quench-hardening 淬火硬化,模具设计与制造专业英语 第2版 ppt 课件,New Words and Expressions,Terms：2.Iron-carbon equilibrium diagram 铁碳平衡相图 ferrite 铁素体 austenite 奥氏体 pearlite 珠光体 carbide 碳化物 bainite 贝氏体 martensite 马氏体 liquid 液态 delta-iron-铁 alpha-iron-
7、铁 gamma-iron-铁,模具设计与制造专业英语 第2版 ppt 课件,Iron-carbon equilibrium diagram,Time-temperature transformation(TTT)diagrams,A Continuous cooling transformation(CCT)curve compared to TTT diagram,亚微观的；普通显微镜下看不出来的,Tempering,During tempering,martensite undergoes a transformation process from that of carbon atoms
8、 supersaturated in iron to a structure termed tempered martensite which consists of highly dispersed submicroscopic carbide particles in a ferrite matrix.The extent of increase in ductility hence toughness and the corresponding reduction in hardness and strength is a function of tempering temperatur
9、e and time.,回火；调和,Annealing,If a steel bar is cooled slowly in a furnace from a temperature above its upper critical temperature to a temperature below the lower critical temperature,the structure of the steel will become ferrite and cementite again.This steel consists of a somewhat coarser grain st
10、ructure that is low in strength,high in ductile and soft.This process of heat treatment is called Annealing.,退火，缓冷，韧化,正火,Normalizing,However,instead of cooling in furnace as described above,the steel is taken out from the furnace and cooled in still air,it is termed Normalizing.A normalized steel ba
11、r possesses higher strength and toughness than its annealed counterpart.,对应物，配对物,Quench-Hardening,If a steel bar is rapidly cooled from its upper critical temperature by plunging it into a coolant such as water or oil(termed quenching),the effect is to transform the austenite into a structure called
12、 martensite.Martensite is a very hard,but brittle constituent of steel.For steels having a carbon content less than 0.8%,a temperature at between 30 deg C to 50 deg C above the upper critical temperature(723 deg C)is used for quenching and the resulting structure comprises martensite and ferrite.,Th
13、e Heat Treatment Process,Basically,Heat Treatment just consists of heating up and cooling down process.These process can be further divided into four steps.,One Step1 Construction of Time-Temperature-Transformation Diagram(TTT)and Continuous Cooling Transformations Diagram(CCT)TTT Diagrams-can be qu
14、ite useful in determining the kinetics of transformation and the nature of the products.The curve shows the time required to complete the transformation at that temperature.,One Step2,CCT Diagrams-Although the TTT diagrams can provide useful information about the structures obtained through non-equi
15、librium thermal processing,they are not rigorously applicable to engineering applications because the assumptions of instantaneous cooling from elevated temperature is far more realistic,and a diagram showing the results of continuous cooling at various rates would be far more useful.,Two Steps,The
16、second step is a heating operation designed to produce an elevated temperature homogeneous single-phase solid solution.The heating should not exceed the eutectic temperature or there might be melting if a cored structure were present.,Three And Four Steps,After soaking to assure a uniform chemistry
17、single phase,the alloy is cooled.The cooling rate of the alloy depends on the property of metal required.The heat treated material is then left for diffusion.Diffusion is necessary to convert the unstable supersaturated solution into the stable structure.,Surface Hardening,For many engineering purpo
18、ses it is desirable for parts to have a hard surface to resist wear and abrasion and the inner portion remains soft and tough to sustain impact loading.This depth of the hardened surface is normally from 0.0001 mm to a few mm depending on applications.These properties can be obtained by surface hard
19、ening which is generally divided into the following three types:,Gas carburizing,Nitriding Method,Principle of Induction Hardening,Questions,What process is used to remove the internal stresses created during a hardening operation?What heat treating process makes the metallic carbides in a metal for
20、m into small rounded globules?What are the main purposes of heat treating?How many heat treating processes are involved in ferrous materials?,Glossary of Terms,1Hardenability 淬透性2hardenability curve 淬透性曲线3hardening capacity 淬硬性（硬化能力）4hardness profile 硬度分布（硬度梯度）5heat treatment procedure 热处理规范6heat tr
21、eatment installation 热处理设备7heat treatment furnace 热处理炉8heat treatment cycle 热处理工艺周期9heat time 加热时间10 heat system 加热系统11 heating up time 升温时间12 heating curve 加热曲线,13high temperature carburizing 高温渗碳14high temperature tempering 高温回火15isothermal transformation 等温转变16isothermal annealing 等温退火17interrupt
22、ed ageing treatment 分级时效处理18local heat treatment 局部热处理19overheated structure 过热组织20pack carburizing 固体渗碳21oxynitrocarburizing 氧氮碳共渗22partial annealing 不完全退火23spheroidized structure 球化组织24recrystallization temperature 再结晶温度,Example 1:This combination of heating and controlled cooling determines not o
23、nly the nature and distribution of the microconstituents,which in turn determine the properties,but also the grain size.（在热处理过程中），加热与冷却控制相结合的方法不仅决定着材料中微观组织的分布和性质（进而决定了该材料的性能），而且也决定了材料内部晶粒的大小。句中第一个and连接的是heating和controlled cooling，第二个and连接的是nature和distribution，而which in turn determine the properties为
24、非限定性定语从句,修饰the nature and distribution。,Language Points&Translating Techniques,Example 2:With most of the mediumcarbon forging steels,alloyed and unalloyed,normalizing is highly recommended after forging and before machining to produce more homogeneous structures,and in most cases,improved machinabi
25、lity.对于大多数中碳锻钢来说，不管它是否合金化，在锻造后或加工前通常推荐采用正火处理工艺，这样有利于形成更均匀的组织，并且在大多数情况下可改善材料的切削加工性能。句首的介词with短语意为“对来说”；in most cases可译为“在大多数情况下”。,二、翻译的标准翻译的任务在于准确而完整地介绍原文的思想内容，使读者对原文的思想内容有正确的理解。然而，怎样才算是准确、完整的翻译呢？要解决这个问题，就需要有一个共同的翻译标准。谈到翻译标准，不免要提到严复的“信、达、雅”。严复在他的一部译著的前言中提出了“信、达、雅”。“信”就是忠实原文，“达”就是表达清楚，“雅”即是文字文雅。后来，鲁迅先
26、生在此基础上又提出了“信”和“顺”这两条标准。“信”和“顺”，即“忠实”、“通顺”，今天已成为公认的两条标准了。,Example 3:,“忠实”是指译文的思想内容必须忠实于原文，这一标准对科技英语尤为重要，因为科技作品的任务在于准确而系统地论述科学技术问题，它要求高度的准确性，特别是对术语、定义、定理和结论的翻译更应重视。然而，忠实原文并不是形式上保持原文，而是内容上保持原文。翻译时切忌逐字死译，这样会有损原意。请看例句：A roughing cut is usually to be followed by a fishing cut.粗切削通常要被精切削跟随。译文的毛病在于虽然词类或句子成分
27、都与原文一致，保持了原文的形式，但却失去了原文的精神。若译成“粗切之后，通常还要精切”才算忠实原文。翻译的第二条标准是“通顺”。“通顺”是指译文的语言形式必须符合汉语规范，翻译时要按照汉语的语法规律和习惯来遣词造句，做到通顺易懂。但要指出，“通顺”是在“忠实”的前提下，任何“顺而不信”都是不行的，属于乱译。,看下面一个例子：The foundation of the machine should not be constructed at a place of conspicuous temperature change,due to direct sunshine,excessive hea
28、t or vibration,or at a place contaminated with soil or dust particles.机床的地基不应建在由于日晒、过热或受震动而引起的温度明显变化的地方，或受尘土污染的地方。这句译文，读起来是通顺的，但仔细一推敲，就叫人不解了，为什么受振会引起温度明显变化呢？问题就出在译文的不“忠实”。译者把原来与temperature change（温度变化）相并列的 excessive heat or vibration（过热或受振）误认为是与sunshine（日晒）相并列的。正确的译文应是：“机床的地基不应建在受阳光直晒而引起温度明显变化的地方、过热
29、或受振动的地方或受尘土污染的地方。”,错译的原因在于译者对原文不求甚解，只满足于译文的通顺。为了防止这种现象的产生，翻译时一定要在透彻理解原文的基础之上，再力求译文的通顺。从上面的例句可以看出，“忠实”与“通顺”这两条标准是辨证的统一。“忠实”是“通顺”的基础，译文不“忠实”，再“通顺”也毫无意义。反之，译文不“通顺”又必然影响到译文的“忠实”，因为只有译文的通顺，才能更确切地表达原意。,掌握必须的专业单词（New Words）掌握常用的专业术语（Glossary of Terms)掌握基本的语法知识掌握基本的翻译技巧,Summary,References,1.Serope Kalpakjian,Steven R.Schmid Manufacturing Engineering and Technology(Fifth Edition)M.国外大学优秀教材制造工程与技术（第五版）影印版，清华大学出版社2006.2月第一版2.P N Rao.Manufacturing TechnologyFoundry,Forming and Welding(Second Edition)M.制造技术铸造、成形和焊接（英文版.原书第 2版）M北京：机械工业出版社，2006.2 3中国机械工业标准汇编金属热处理卷北京中国标准出版社1999 4.,
