《海洋石油常用中英文对照词汇.docx》由会员分享，可在线阅读，更多相关《海洋石油常用中英文对照词汇.docx（52页珍藏版）》请在三一办公上搜索。
1、海洋石油常用中英文对照词汇A A-60 fire door a-hundred-year return period abrasive abrasive paper AC generator AC motor accelerated corrosion testing acceptance criteria access hole (for welding) = cope hole accommodation and power platform (APP) according to = in accordance with = in line with = as per = in the l
2、ight of acetylene gas acid electrode acid proof cement additive adhere to adherence to adjacent columns adverse combination of loads adverse condition A-60级防火门 百年一遇 磨料 砂纸 交流发电机 交流电动机 加速腐蚀试验 合格准则 (焊接)工艺孔 生活动力平台 按照 乙炔 酸性焊条 防酸水泥 添加剂 遵守 遵守 相邻立柱 载荷的不利组合 不利条件 aeronautical radio system AFC (approved for co
3、nstruction) aforementioned aft winch agitator air blower air compressor air driven pump air hoister air manifold air tight test air-hose aircraft obstruction beacon alarm buzzer alarm horn aliphatic polyurethane allowable (working) stress Aluminum alloy anode Aluminum ingot aluminum paint aluminum s
4、heet ambient air temperature ambient temperature 航空无线电系统 建造批准 上述 船艉绞车 搅拌器 鼓风机 空气压缩机 气动泵 气动绞车 气包 气密性试验 风带 航空障碍灯 报警蜂鸣器 报警喇叭 脂肪族聚氨脂漆 许用应力 铝合金阳极 铝锭 银粉漆 铝皮 环境气温 环境温度 1 anchor block anchor bolt anchor ground anchor pile anchor profile/pattern anchor rack anchoring buoy angle of incidence angle of reflecti
5、on angle probe method angle steel angle valve anode core anode end face geometry anode life anode potential anode stand-off post anode resistance anti-electrostatic floor anticorrosive paint antipollution measures API specified requirements apparent batter 地锚块 地脚螺栓 锚地 锚桩 涂装表面的粗糙度 锚架 锚泊浮筒 入射角 折射角 超声波
6、斜射探伤 角钢 角阀 阳极芯子 阳极端面几何形状 阳极寿命 阳极电位 支架式阳极的立柱 阳极电阻 防静电地板 防锈漆 防污染措施 API规定的要求 视斜度 applicable API specification approach-departure sector appurtenance = attachment= accessory = auxiliary arc air gouging arc cutting arc strike argon arc welding argon arc welding machine articulated tower mooring system ar
7、tificial island as per as-built as-built dossier as-built drawing as-rolled assemble assembly associated gas at the option of A atmospheric diving system = unpressurized diving system atmospheric vent API适用规范 直升飞机起落扇形区 附件 碳弧气刨 电弧切割 弧击 氩弧焊 氩弧焊机 铰接塔系泊系统 人工岛 按照 完工 完工资料 完工图 轧制状态 组装 组装 伴生气 按A的意愿 常压潜水系统 放
8、空管 2 attachment auto fire alarm system automatic spraying system B (to be) buttered back chipping back gouging backing weld backpressure regulator (self contained) backwash return pump backwash surge tank Ball hardness ball valve bar bar chart barge bumper barge strength and stability barrel base me
9、tal basic design basic electrode = lime type covered electrode 附件 火灾自动报警系统 自动喷淋系统 (焊接的)长肉 清根 反面气刨 打底焊道 背压式调节阀反冲洗回流泵 反冲洗罐 布氏硬度 球阀 圆钢 方钢六角钢等 统计用的柱状图 靠船件 驳船强度及稳性 加厚段 母材、基本金属 基本设计 碱性焊条 battery room blowout preventer system (BOP system) beam depth beam path distance bearing strength of the ground bearing
10、 stress before welding is initiated bending moment bending stress bevel bid drawing bevel angle beveling / chamfering bilge / fire pump bilge alarm system bid / tender for blast cleaning blind flange blind spectacle flange blow count blowdown vessel blowhole; gas pore blowout preventer stack 蓄电池间 防喷
11、器系统 梁高 超声波发射程距 地基承载力 支撑应力 始焊前 弯矩 弯曲应力 开坡口 坡口 坡口面角度 招标图纸 舱底污水-消防两用泵 污水报警系统 投标 喷砂除锈 盲法兰 快速盲法兰 打桩的锤击数 排放罐 气孔 防喷器组 3 buoyant turret mooring boat landing bolt, nut and washer bolted connection boom boom angle bore hole boss with plug bottom echo bottom sitting drilling platform boundary condition bow box
12、 beam box type joint brace bracelet anode branch member breathing apparatus , respirator bridge bridge (overhead) crane brittleness brush coating buckle fastener 浮筒转塔式系泊 登船平台 螺栓、螺母及垫片 螺栓连接 吊机扒杆 吊机倾斜角 镗孔 带有丝堵的管座 底面回声 坐底式钻井船 边界条件 船艏 箱形梁 箱形节点 拉筋 手镯式阳极 支杆 防毒面具 栈桥 天车吊 脆性 用毛刷涂漆 绑带 bulb angle build-up gird
13、er bulk head burn through burner burr and flashing business and management butt-welded seam butterfly valve C cable layer cable rack / tray caisson caisson washing pump caisson-type platform can cantilever beam cantilever jack-up rig cantilever well module cap beam capped steel capsizing lever 球扁钢 组
14、合梁 隔板、舱壁 烧穿 气焊工 飞边毛刺 经营管理 对接焊缝 蝶阀 敷缆船 电缆托架 沉箱 洗舱泵 沉箱式平台 段 悬臂梁 悬臂自升式钻井船悬臂式井口模块 帽梁 半镇静钢 倾覆力臂 4 capsizing moment = overturn moment carbon arc air gouging carbon dioxide cylinder carbon equivalent carbon-dioxide(CO2) arc welding cargo master system cargo tank cleaning machine carrier carry out = perform
15、 = conduct = execute catenary anchor leg mooring (CALM) cathodic protection cellar deck cellar shutdown panel (CSDP) cement grout cementing vessel center line center of buoyancy center of floatation center of gravity center punch central control room (CCR) central processing platform 倾覆力矩 碳弧气刨 二氧化碳气
16、瓶 碳当量 二氧化碳气体 保护电弧焊 货油舱总监控系统 洗舱机 小车 进行、执行 悬链锚腿系泊 阴极保护 底甲板 井口系统关断盘 水泥浆 固井船 中心线 浮心 漂心 重心 冲子 中央控制室 中心处理平台 centrifugal pump centrifuger ceramic fibres ceramic tiles certifying authority chain block chair with arm-rest chamfering channel steel charpy-V notch energy charpy-V notch impact test chart datum c
17、heck randomly check valve checkered plate chemical injection package chemical injection system chemical seal chipping hammer chisel chord member christmas tree circumference 离心泵 离心机 防火陶棉 瓷砖 第三方检验机构 倒链 带扶手的半软椅 开坡口 槽钢 夏比V形缺口韧性值 夏比V形缺口冲击试验 海图基准面 抽检 止回阀 花纹板 化学注入撬 化学注入系统 化学密封 敲渣锤 风铲 弦杆 采油树 周长 5 circumfer
18、ential weld classification survey clean water injection pump clean water surge tank clearance client close drain tank closed / open circuit closed drain pump clustered well heads CO2 cylinder unit CO2 extinguisher coal tar epoxy paint coaming coating coating interval coefficient cold formed pipe col
19、d shut cold work collapse ring column combustible gas detector 环焊缝 入级检验 清水注入泵 清水缓冲罐 间隙 业主、顾客 闭式排放罐 闭 / 开路 闭式排放泵 丛式井口 CO2气瓶组 CO2灭火器 含焦油环氧涂料挡水扁铁 涂装 涂漆间隔 系数 冷卷管 冷隔 冷加工、冷作 加强环板 立柱 可燃气体探测器come-along commercial blast cleaning commissioning compile and maintain a document complete penetration groove weld c
20、ompletion riser complex joint compliance with comply with composite rockwool ceiling composite rockwool panel concentric reducer conceptual design concrete platform condensate drum condensing water conductor conductor guide cone conform to = stick to = adhere to connection consumption rate continuou
21、s beam 手扳葫芦 普通级喷砂除锈 调试 编制和保存文件 全熔透坡口焊 完井立管 复杂节点 符合 符合 复合岩棉天花板 复合岩棉板 同心大小头 概念设计 混凝土平台 冷凝液罐 冷凝水 隔水套管 套管导向 大小口、锥体 符合、遵守 节点、连接 阳极消耗率 连续梁 6 continuous double fillet weld continuous welding contract contraction stress contractor control valve (accessories handwheel) control valve assembly coordinates coor
22、dination cope hole corrective and preventive action correlation curve corrosion allowance corrosion coupon corrosion protection corrugated plate interceptor couplant coupling crack crane barge, crane vessel crane support crater crawler crane 双面连续贴角焊 连续焊 合同 收缩应力 承包商 带手轮的控制阀 控制阀总成 坐标系 协调 (焊接)工艺孔 纠正和预防
23、措施 相关曲线 腐蚀余量 腐蚀挂片 防腐 斜板分离器 UT用的耦合剂 联轴器、管箍 裂纹 起重船 吊机支撑 焊口 履带吊车 criteria cross angle cross section crow bar cruciform bollard crude cooler crude filter crude heat exchanger crude loading /export pump crude loading pump crude oil drain tank crude preheat exchanger crude suction strainer crude transfer
24、cup support curing time current capacity current density current direction curvature radius customer (验收)标准 交叉角 横截面 撬杠 单十字带缆柱 原油冷却器 原油过滤器 原油换热器 原油外输泵 原油装载泵 原油排放舱 原油预热器 原油吸入滤器 原油输送泵 垫墩 固化时间 电流容量 电流密度 海流方向 曲率半径 客户 7 cut by torch cut off cutoff allowance cutting plan cutting sheet D (in) duplicate (to)
25、 drive piles DAC curves daily diesel filter damage-prone connection damper, dampener DC generator Decibel (dB) deck beam deck cover deck crane deck water seal unit deep freeze compressor deepwater jacket defect /default /disconnection deflection 以火焰切割 割除、割除物 切割裕量 排板图 单件图 一式两份 打桩 距离-振幅曲线 日用柴油滤器 易破坏的节
26、点 减震器 直流发电机 分贝 甲板梁 甲板敷料 甲板吊车 甲板水封装置 深冷压缩机 深水导管架 缺陷 挠度 dehydration degassing vessel dehydration preheater dehydration feed pump delivery of materials derrick barge desander design basis design parameters detail detail design develop / establish a document dew point DFT (dry film thickness) diagonal b
27、race dial gauge diaphragm diaphragm valve die stamp diesel daily tank diesel filter coalescer diesel generator set diesel oil daily tank with heater diesel pump 脱水除气器 脱水预热器 电脱水供给泵 材料交货 回转式起重船 除砂罐 设计基准 设计参数 详图 详细设计 编制文件 露点 干膜厚度 斜拉筋 百分表 隔板 隔膜阀 钢印 柴油日用罐 柴油过滤净化装置 柴油发电机组 柴油日用罐柴油泵 8 diesel storage tank di
28、esel storage tank with heater diesel tank diesel transfer pump differential pressure control valve diffuser dihedral angle dimensional checks direct / alternating current arc welding direct current emergency supply disassembling discontinuity displacement oil tank distortion from welding distress si
29、gnals diver diver support vessel document approval and issue documentation dog dolphin domestic sea water pump double agent facility 柴油储罐 柴油储罐 柴油罐 柴油输送泵 差压控制阀 布风气 二面角 尺寸检查 直/交流电弧焊 直流应急电源 拆除 缺陷 置换油罐 焊接变形 遇险呼救信号 潜水员 潜水作业船 文件的批准和下发 文件编制 组装用的刀把 系缆柱 生活海水泵 双介质灭火装置 double bed double bevel groove double bol
30、lard double groove double probe method double V groove doubler plate down hill welding drain pit draught gauge drawing and specification drawing types 图纸种类有： conceptual drawing basic drawing bid drawing design drawing fabrication drawing shop drawing as-built drawing dredger drift pin drift test 双层床
31、 k形坡口 双柱带缆桩 双面坡口 双探头法 双面V形坡口(X形) 垫板、包板 向下焊 排放池 吃水标尺 图纸及技术规格书 图纸种类 概念图纸 基本设计图纸 招标图纸 详细设计图纸 加工设计图纸 车间加工图纸 完工图 挖泥船 心轴、销子 管流试验、管线试通9 drill drilling module drilling platform drilling template drillship, drilling ship driving voltage dry chemical extinguisher dry-type tree dryer during the course of fabri
32、cation during the life of structures dye penetrant inspection dynamic-positioning rig E Earth lead eccentric reducer echo height edge crimping edge preparation effective throat thickness elbow electric dehydrator 钻头 钻井模块 钻井平台 钻井基盘 浮式钻井船 驱动电压 干粉灭火器 干式采油树 烘箱 在制造过程中 结构寿命期间 着色检验 动力定位钻井船地线 偏心大小头 回波高度 (卷管
33、的)压头 坡口加工 焊缝计算厚度 弯头 电脱水器 electric desalter electric drill electric heater electric submersible pump electric-hydraulic valve electrical connection electro-slag welding electrochemical property electrode electrode covering electrode holder electrolyte elevation (EL) elongation emergency air compresso
34、r emergency ballast control system emergency BOP recovery system emergency generator emergency light emergency power station emergency shutdown emergency shutdown system (ESD) emergency switch board 电脱盐器 手电钻 电加热器 电潜泵 电-液操作阀 导电连接 电渣焊接 电化学特征 电焊条 焊条药皮 焊把、焊钳 电解质 标高、立面图 延伸率 应急空压机 应急压载控制系统 防喷器紧急回收系统 应急发电机
35、 应急照明灯 应急电站 应急关断 应急关断系统 应急开关柜 10 emergency switch room emery cloth emulsion transfer pump engine room engineering geotechnical vessel entire length equal angle equation equipment base erection ERW (electric resistance welding) escape route essential variable excess of weight existing structure explo
36、sion proof equipment exposure distance extent of defect in % extent of inspection extent of repair external surface of brace extra margin of stress 应急配电间 金刚砂布 乳化油输送泵 动力舱、机舱 工程地质船 全长 等边角钢 公式 设备底座 安装 电阻焊 逃生路线 焊接基本参数 超重 已有结构 防爆设备 防火距离 缺陷百分比 检验范围 返修率 拉筋的外表面 应力裕量 F fabricated wide flange shape fabricatio
37、n aids fabrication design fabrication phase fabrication sequence fabrication yard face bend test facsimile transceiver fastener fatigue damage field assembly field mating point field splice field weld fifty year return period file filler metal final fabrication tolerance finish coat finished product
38、 焊接成的宽翼缘型钢 制造辅助物 加工设计 制造阶段 制造顺序 制造场地 表面弯曲试验 传真收发两用机 紧固件 疲劳破坏 空间组对、现场组对 海上对接点 现场拼接 现场焊缝 五十年一遇 锉刀 填充金属 最终制造公差 面漆 成品 11 finite element analyses fire alarm siren fire and gas detecting system fire control panel fire damper fire door closer, fire proof door fire extinguishing system fire fighting water,
39、fire water fire foam hydrant fire hose station, hose box fire monitor fire panel fire proof wall, fire wall fire protected plastic tiles fire protection wall fire station fire water / foam monitor fire water deluge system fire water hose rock fire water hydrant fire water jockey pump fire water lift
40、 pump 有限元分析 火灾警笛 火灾-可燃气探测系统 消防控制盘 防火风闸 防火门 消防系统 消防水 消防泡沫栓 消防箱 消防炮 火灾-可燃气体 报警显示盘 防火墙 防火塑料地板 防火墙 消防软管箱 消防炮 大水量灭火系统 消防水软管 消防水栓 消防水增压泵 消防水提升泵 fire water pump fire-fighting vessel, fire boat fireman box first aid kit first coat first stage hydrocyclone first stage separator fit-up fitter fixed crude oil
41、washing machine fixed drilling platform fixed tower SPM flame arrester flame cutting flame cutting droplets and debris flame cutting machine flame cutting torch flammability limits flange flare assembly flare boom flow indicator (FI) 消防泵 消防船 消防员箱 急救箱 底漆 一级水利漩流器 一级分离器 坡口组对 组装工 固定式原油清洗机 固定式钻井平台 塔系泊 阻火
42、器 火焰切割 火焰切割形成的熔滴 和料头 火焰切割机 火焰割枪 可燃度极限 翼缘、法兰 火炬总成 火炬臂 流量显示器 12 flare drum flare pilot gas flare scruber flare tower flat bar flat plate anode flat welding flaw flaw detectability flaw echo flexible hose flexible riser floater controlled valve floating cargo hose floating loading hose floating oil pro
43、duction and storage unit (FPSU) floating oil storage unit floating production platform floating production, storage and off-loading tanker floating state flooding floppy disk 闪蒸罐 火炬引燃器 火炬分液器 火炬塔 扁钢 扁阳极 平焊 裂纹 缺陷检测灵敏度 缺陷回声 柔性软管 挠性立管 浮球控制阀 浮式输油软管 浮式装油软管 浮式生产储油装置 浮式储油装置 浮式生产平台 浮式生产储油外输轮 飘浮状态 注水 软盘 flow
44、chart frame structure flow quantity recorder (FQ) flow switch flux flux cored arc welding (FCAW) flux-cored electrode flux-cored wire foam extinguishing system foam monitor foam station fog horn, fog signal folding bed folding chair foot print foot valve forecastle foreman forged steel (FS) fork lif
45、t forming forming of plates into tubular formula/equation of carbon equivalent 流程图 梁格结构 累计流量计 流量开关 焊药 药芯焊 管状焊条 药芯焊丝 固定式泡沫灭火系统 泡沫炮 泡沫站 雾笛 折叠床 折叠椅 被交位置 底阀 艏楼 领班 锻钢 铲车、叉车 压制成型 由板卷成管 碳当量公式 13 four way valve fracture toughness free water hnockout vessel fresh water pressure vessel fresh water pump fresh
46、water tank with electric heater friction coefficient fuel gas compressor package fuel gas heater fuel gas scrubber fuel gas treatment package fuel oil drain tank fuel pump full coupling full penetration weld funnel-shaped guide furnace fusible plug fusion / bond line G (to be) ground flush gantry cr
47、ane 四通阀 断裂韧性 游离水分离器 淡水压力罐 淡水泵 淡水罐摩擦系数 燃气压缩机撬 燃料气加热器 燃气洗涤器 燃料气处理撬 燃料油排放罐 燃油泵 全螺纹接头 全熔透焊缝 喇叭口状导向 熔炉、加热炉 易熔塞 熔合线 磨平 龙门吊 gap gauge gas bottle gas cutting gas cutting machine with magnetic wheels gas detector gas export facility gas injection module gas metal arc welding (GMAW) gas processing plant gas s
48、hielded arc welding gas tungsten metal arc welding (GTAW) gas turbine generator set gas turbine power generator gas welding gasket gate valve geophysical survey vessel girders and webs girth weld global positioning system (GPS) globe valve (normally closed) glycerin 间隙尺 气瓶 气割 磁轮式气割机 可燃气体探测器 天然气外输设备 注气组块 熔化极气体保护焊 天然气处理厂 气体保护电弧焊 钨极气体保护焊 燃气轮机发电机组 燃气轮机发电机 气焊 垫圈 闸阀 物探船 水平桁材和垂直桁材 环缝 全球定位系统 截止阀 甘油 14 go
