《【英国标准word原稿】BS EN 12441998 Adhesives. Determination of the colour andor colour changes of a.doc》由会员分享，可在线阅读，更多相关《【英国标准word原稿】BS EN 12441998 Adhesives. Determination of the colour andor colour changes of a.doc（15页珍藏版）》请在三一办公上搜索。
1、豆丁网：BRITISH STANDARDAdhesives Determination of the colour and/or colour changes of adhesive coats under the influence of lightThe European Standard EN 1244:1998 has the status of aBritish StandardICS 83.180| BS EN1244:1998|第 5 页 共 15 页豆丁网：Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 09:00:
2、38 GMT+00:00 2006, Uncontrolled Copy, (c) BSI|NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 1244:1998National forewordThis British Standard is the English language version of EN 1244:1998.The UK participation in its preparation was entrusted to Technical CommitteeSTI/52
3、, Adhesives, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate t
4、hem in the UK.A list of organizations represented on this committee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section enti
5、tled International Standards Correspondence Index, or by using theFind facility of the BSI Standards Electronic Catalogue.A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application.Compliance wit
6、h a British Standard does not of itself confer immunity from legal obligations.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover.Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 09:00:38 GMT+00:0
7、0 2006, Uncontrolled Copy, (c) BSIAmd. No.DateText affectedThis British Standard, having been prepared under the direction of the Sector Board for Materials and Chemicals, was published under the authority of the Standards Board and comes into effect on 15 July 1998BSI 1998ISBN 0 580 29637 7Amendmen
8、ts issued since publicationEUROPEAN STANDARDEN 1244NORME EUROPE ENNEEUROPA ISCHE NORMFebruary 1998ICS 83.180Descriptors: Adhesives, coatings, tests, colorimetry, artificial light tests, determination, colour fastness, specimen preparationEnglish versionAdhesives Determination of the colour and/or co
9、lour changes of adhesive coats under the influence of lightAdhe sifs De termination de la couleur et/ou des changements de couleur des reve tements adhe sifs sous linfluence de la lumie reKlebstoffe Bestimmung der Farbe und/oder der Farba nderung von Klebaufstrichen unter LichteinwirkungLicensed Cop
10、y: sheffieldun sheffieldun, na, Sat Oct 28 09:00:38 GMT+00:00 2006, Uncontrolled Copy, (c) BSIThis European Standard was approved by CEN on 24 January 1998.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the s
11、tatus of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A
12、 version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland,
13、France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.CENEuropean Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r NormungCentral Secretariat: rue de Stassart 36, B-1050 Bru
14、ssels1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN nationalMembers.Ref. No. EN 1244:1998 EPage 5EN 1244:1998BSI 1998ForewordThis European Standard has been prepared byTechnical Committee CEN/TC 193, Adhesives, theContentsPageLicensed Copy: sheffieldun sh
15、effieldun, na, Sat Oct 28 09:00:38 GMT+00:00 2006, Uncontrolled Copy, (c) BSIsecretariat of which is held by AENOR.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 1998, and conflicting nati
16、onal standards shall be withdrawn at the latest by August 1998.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece
17、, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.Foreword 21Scope 32Normative references 33Definitions 34Principle 35Safety 36Apparatus 37Test specimens 48Procedure 49Expression of results 510Test report 5Licensed Copy: sheffield
18、un sheffieldun, na, Sat Oct 28 09:00:38 GMT+00:00 2006, Uncontrolled Copy, (c) BSI1 ScopeThis European Standard is applicable to solvent-based, dispersion, hot-melt and reactive adhesives, their basic constituents, and related products the coating of which are coloured and/or subject to a change of
19、colour by light. It describes a method of measuring the colour of an adhesive coat and the magnitude of a change of colour under the influence of light.A change of colour of an adhesive coat can be very undesirable in practice, in particular if goods made of white or bright-coloured materials such a
20、s paper, textiles or leather are adhesively bonded and material surfaces are contaminated by coated adhesive.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in
21、the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard onlywhen incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to
22、applies.EN 923, Adhesives Terms and definitions. EN 1066, Adhesives Sampling.EN 1067, Adhesives Examination and preparation of samples for testing.CIE Publication No 15.2 (1986), Colorimetry.ISO 554:1976, Standard atmospheres for conditioning and/or testing Specifications.ISO 2602:1980, Statistical
23、interpretation of test results Estimation of the mean Confidence interval.ISO 105-B02:1988, Textiles Tests for colour fastness Part B02: Colour fastness to artificial light: Xenon arc fading lamp test.3 DefinitionsFor the purposes of this standard, the definitions in accordance with EN 923, CIE Publ
24、ication No 15.2, and the following definitions apply:3.1adhesive coatadhesive layer applied to an adherend3.2adhesive filmadhesive coat separated from the substrate after setting3.3 coloursensation perceived by the human eye4 PrincipleThe colour of an adhesive coat is measured by colorimeter, conver
25、ting its readings according to the CIE recommendations (CIE publication No 15.2) to CIELAB values.The change of colour of an adhesive coat is determined by exposing an adhesive coat for a specified time under specified conditions to artificial light that is very similar in spectral composition to na
26、tural daylight but greater in intensity, and then measuring the colour of the coat before and after the exposure to light, and calculating the CIELAB colour differences.5 SafetyPersons using this standard shall be familiar with normal laboratory practice.This standard does not purport to address all
27、 the safety problems, if any, associated with its use.It is the responsibility of the user to establish safety and health practices and to ensure compliance with any European and national regulatory conditions.6 Apparatus6.1 Cardboard, about 250 g/m2 in mass in relation to the surface, with a smooth
28、 surface and a very high degree of whiteness as carrier for adhesive coats and film.The cardboard shall be free from hydroxybutyl toluene (BHT) or other ingredients liable to cause discoloration by migration to avoid interferences or false results.6.2 Glass sheets, with a completely even surface(pla
29、te glass) for the preparation of adhesive film.6.3 Coating device, allowing the spreading of the adhesive to be tested on cardboard (see 6.1) or glass sheet (see 6.2) producing on a flat surface a coating of100 mm 3 30 mm and a uniform thickness of(0,1 0,02) mm after drying, cooling and setting, whi
30、ch shall be measured by any suitable methods.6.4 Colorimeter, for measuring the colour of test specimens both unexposed and exposed to light (see also 8.2) and converting the readings to the CIE colour space values L*, a* and b* and calculating the CIELAB colour differences DL*, Da*, Db* and DE*ab a
31、utomatically according to the CIE recommendations (CIE publication No 15.2). This colorimeter shall alsobe suitable for the determination of the yellowness index YI.Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 09:00:38 GMT+00:00 2006, Uncontrolled Copy, (c) BSI6.5 Light exposure apparatus,
32、 containing the following elements.6.5.1 Xenon arc lamp, of correlated colour temperatures ranging from 5 000 8K to 6 500 8K to conform with ISO 105:B02 and a rating in the range1,5 kW (as suggested in ISO 105:B02), dependent on the type of equipment and cooling system.6.5.2 Light filter, placed bet
33、ween the xenon arc lamp and specimen holders so that the ultra-violet spectrum is steadily reduced.The transmission of the filter shall be at least 90 %between 380 nm and 750 nm, falling to 0 % between310 nm and 320 nm.6.5.3 Heat filter. The spectrum of the xenon arc contains an appreciable amount o
34、f infra-red radiation.For minimizing this radiation an efficient glass or water filter system is necessary.6.5.4 Test chamber, of a light source is surrounded by10 or more holders made from an inert material for test specimens (see 7.1), size 130 mm 3 45 mm, arranged in an equal distance on a carous
35、el in such a manner that the intensity of radiation on the plane of the specimen reaches about 1 000 W/m2. The intensity of radiation shall not vary more than 10 % from the mean value calculated on all samples. The rotation rate of the carousel shall be from 1 min21 to 5 min21.The irradiation of the
36、 test specimens shall be selectable between turning sample operations (periodic light-dark cycles) or stationary sample operations (permanent exposure to light).A humidified stream of air shall pass through the test chamber over the surfaces of the specimens.The relative humidity of the test chamber
37、 shall be controlled by a contact hygrometer.6.5.5 Cover mask. For a partial exposure of the test specimens to light cover masks of stainless steel are required, opening after specified times an unexposed section of the surface of the specimens, of a minimum size of 30 mm 3 15 mm, for exposure.The m
38、asks shall tightly cover the unexposed part of the specimen so that a sharp borderline is produced between the unexposed and the exposed parts.In order to avoid adhesion of the adhesive coat to the test specimen it is useful to coat the surface of the cover mask in direct contact with the specimen w
39、ith an inert release agent (e.g. a polyfluorohydrocarbon).6.5.6 Black panel temperature sensor, for measuring the temperature of the surface of the test specimens when tested.6.5.7 Radiation measuring device, allowing measurement of the intensity (W/m2) and/or the dosage of radiation (J/m2) on the l
40、evel of the test specimens.NOTE For assessing the dosage of radiation the Blue WoolReference Standard specified in ISO 105-B02 should be used.7 Test specimens7.1 Preparation of the test specimens Take a sample of the adhesive to be tested in accordance with EN 1066 and examine and prepare itin accor
41、dance with EN 1067.Pour a test portion of this sample on a sheet of cardboard (see 6.1) and spread the adhesive using a coating device (see 6.3) to give coats of size(100 mm 3 30 mm).During coating use a generous quantity of adhesive of thickness (0,1 0,02) mm after complete evaporation of all volat
42、ile adhesive constituent (e.g. water,solvents, etc.).The dry coat shall be of uniform thickness, have uniform surface structure and shall not contain any bubbles.To fulfil these requirements, the adhesive to be tested shall be applied on cardboard (see 6.1) or on a glass sheet (see 6.2), if necessar
43、y after dilution with a suitable solvent, in several coats (always after drying the preceding coat).If the cardboard (see 6.1) is deformed or damaged by the application of the adhesive, prepare an adhesive film by coating the adhesive on a glass sheet (see 6.2) and attach the film in full contact to
44、 the cardboard (see 6.1) forming a test specimen.A suitable release agent shall be used in a required amount to facilitate or to allow separation of the adhesive film from the glass sheet.Care shall be taken when attaching the adhesive film to the cardboard to ensure that the surface covered with the release agent is brought into contact with the cardboard.7.2 Number of test specimensUnless otherwise indicated prepare and use, for each test, five test specimens.NOTE Some adhesive
