《【BS英国标准word原稿】BS EN 13954 Thermal spraying — Acceptance inspection of thermal spraying .doc》由会员分享，可在线阅读，更多相关《【BS英国标准word原稿】BS EN 13954 Thermal spraying — Acceptance inspection of thermal spraying .doc（17页珍藏版）》请在三一办公上搜索。
1、 ，如果你需要更多标准可以到 如果你购买的文档存在缺页、字迹模糊、乱码等情况，请大家通过论坛消息与我联系。BRITISH STANDARDBS EN1395-4:2007Thermal spraying Acceptance inspection of thermal spraying equipment Part 4: Plasma sprayingThe European Standard EN 1395-4:2007 has the status of aBritish StandardICS 25.220.20 ，如果你需要更多标准可以到 如果你购买的文档存在缺页、字迹模糊、乱码等情况
2、，请大家通过论坛消息与我联系。BS EN 1395-4:2007National forewordThis British Standard was published by BSI. It is the UK implementation of EN 1395-4:2007. This standard together with BS EN 1395-1, BS EN 1395-2, BS EN 1395-3, BS EN 1395-5, BS EN 1395-6 and BS EN 1395-7 supersedes BS EN 1395:1996.The UK participatio
3、n in its preparation was entrusted to Technical CommitteeSTI/40, Thermally sprayed inorganic finishes.A list of organizations represented on STI/40 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsib
4、le for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amd. No.DateCommentsThis British Standard was published under the authority of the Standards Policy and Strategy Committeeon 28 February 2007 BSI 2007ISBN 978 0 580 50278 1Amendments issue
5、d since publicationEUROPEAN STANDARD NORME EUROPENNEEUROPISCHE NORMEN 1395-4January 2007ICS 25.220.20Supersedes EN 1395:1996English VersionThermal spraying - Acceptance inspection of thermal spraying equipment - Part 4: Plasma sprayingProjection thermique - Contrle dacceptation du matriel de project
6、ion thermique - Partie 4: Projection plasmaThermisches Spritzen - Abnahmeprfungen fr Anlagen zum thermischen Spritzen - Teil 4: PlasmaspritzenThis European Standard was approved by CEN on 23 December 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the c
7、onditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in t
8、hree official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.CEN members are the national standards bodies of
9、 Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN
10、COMMITTEE FOR STANDARDIZATION C O M I T EUR O P EN DE NOR M A L I S A TI ON EUR O P I S C H ES KOM I TEE F R NOR M UNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members.Ref. No. EN 1395-4
11、:2007: EEN 1395-4:2007 (E)ContentsPageForeword.31Scope .42Normative references .43Terms and definitions .44Principles of acceptance inspection.45Procedure of acceptance inspection .56Designation .67Inspection report.6Annex A (informative) Inspection report for plasma spraying equipment (initial test
12、/retest) .7Bibliography .99ForewordThis document (EN 1395-4:2007) has been prepared by Technical Committee CEN/TC 240 “Thermal spraying and thermally sprayed coatings”, the secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publicat
13、ion of an identical text or by endorsement, at the latest by July 2007, and conflicting national standards shall be withdrawn at the latest by July 2007.This document together with EN 1395-1, 1395-2, 1395-3, 1395-5, 1395-6 and 1395-7 supersedes EN1395:1996.EN 1395 consists of the following Parts, un
14、der the general title Thermal spraying Acceptance inspection of thermal spraying equipment: Part 1: General requirements; Part 2: Flame spraying including HVOF; Part 3: Arc spraying; Part 4: Plasma spraying; Part 5: Plasma spraying in chambers; Part 6: Manipulator systems; Part 7: Powder feed system
15、s.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy
16、, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.1ScopeThis European Standard specifies requirements for the acceptance inspection of thermal spraying equipment, in this case plasma spraying, use
17、d in spray jobs to produce thermally sprayed coatings of reproducible quality.This part should be used in conjunction with EN 1395-1, which includes general requirements and explanations of procedures.2Normative referencesThe following referenced documents are indispensable for the application of th
18、is document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.EN 657:2005, Thermal spraying Terminology, classificationEN 1274:2004, Thermal spraying Powders Composition, technical supply co
19、nditionsEN 1395-7, Thermal spraying Acceptance inspection of thermal spraying equipment Part 7: Powder feed systems3Terms and definitionsFor the purposes of this document, the terms and definitions given in EN 657:2005 and the following apply.3.1high voltage ignition deviceunit that generates a high
20、 voltage (kV) and low current (mA) between the electrodes of the plasma spraying torch in order to ignite the arc4Principles of acceptance inspection4.1GeneralThe following clauses reveal state of the art technology in thermal spray equipment and the minimum requirements concerning a stable paramete
21、r setting and maintenance according to the classes given in Annex A.4.2High-voltage ignition deviceOther components and functions of the spraying equipment and other machines and/or equipment operated near by to the spraying equipment shall not be affected by operation of the high-voltage ignition d
22、evice.4.3Plasma gasesThe plasma spraying equipment shall be designed and installed in such a manner, that safe operation with plasma gases specified by the user will be achieved.4.4Plasma spray nozzleProcessing of the spraying powder shall be possible without producing any disturbing deposits on and
23、/or in the nozzle. Nozzles with different shapes and powder ports (internal or external) may be used for special applications.4.5Spraying powder feed unitThe powder feed unit shall be suitable for operation with the spraying equipment to be taken.The unit shall permit uniform processing of the powde
24、r required. It shall be possible to adjust the powder feed rate. The set points shall be constant and reproducible, which is a precondition for this being adequate and constant carrier gas pressure and flow.5Procedure of acceptance inspection5.1GeneralSpraying equipment shall be deemed properly supp
25、lied for all suitable spraying applications and for use with all suitable spraying materials required for the spraying process if it complies with the following requirements:5.2Electrical powerProof of the power rating required shall be given by 20 min of spraying with the parameters for aluminium o
26、xide according to EN 1274:2004, 12.1 as recommended by the equipment manufacturer.During the test, the following items will be examined: electrical control; gas control; cooling water temperature.Limits of deviation: see Annex A; Class A and Class B.After stabilisation of arc and plasma, the deviati
27、on of the voltage (variable parameter) from the set point shall not exceed 3 % (Class A) and 12 % (Class B).5.3High-voltage ignition deviceThe high-voltage ignition device shall be deemed to meet the requirements given in 4.2 if it does not interfere with any appliances and functions of the spraying
28、 equipment during the test as specified in 5.2. There should be no excessive erosion wear visible on the nozzle (spark).5.4Plasma gasesThe system shall be deemed to comply with the specified requirements if the following requirements are satisfied by the acceptance inspection. The values of gas pres
29、sure and gas flow shall not deviate by more than 1,5 % (Class A) and 5 % (Class B) from the set points over a 20 min period of spraying. If the secondary gas is the variable parameter, the deviations from the set point shall not exceed 3 % (Class A) and12 % (Class B) after stabilisation. Setting the
30、 primary gas pressure and/or flow rate shall not affect the corresponding values of the secondary gas and carrier gas and vice versa.5.5Plasma spray nozzleThe nozzle shall be deemed to comply with the requirements specified in 4.4 if there are no disturbing deposits of spraying material on or in the
31、 nozzle when testing as specified in 5.2.5.6Powder feed unitThe suitability of the system to process powders as specified in 4.5 shall be tested according to EN 1395-7.6DesignationAcceptance inspection of the thermal spraying equipment for plasma spraying shall be designated as follows:Acceptance in
32、spection according to EN 1395-4.7Inspection reportAn example for the inspection report is given in Annex A.Annex A(informative)Inspection report for plasma spraying equipment (initial test/retest)The initial test/retest fulfils the requirements of the acceptance inspection according to EN 1395-4.Use
33、r: . Manufacturer:. Year of manufacture: . Type of equipment: . Type of spraying gun: . Powder used for testing: .Type of powder feed unit: .Size range: .CE-documentation complete: yes / noItem tested, where applicableFull scaleSet pointChange after 20 minute continuous testingLimitEvaluationactual
34、valuemaximum deviation in %in %passedfailedmin.max.Class AClass BElectrical powercurrentA 1,5 5voltageV 1,5 5Primary gaspressurebar 1,5 5flow)Nl/min1 1,5 5Secondary gaspressurebar 1,5 5flowNl/min1) 1,5 5Carrier gaspressurebar 1,5 5flowNl/min1) 1,5 5Cooling waterflowl/min 5 10inlet temperature to spr
35、ay gunC5 C10 C1)Referred to temperature 0 C and normal pressure (1 013,25 hPa).High-voltage ignition device (interferes with other devices or functions):yes / no Deposits:yes / no Nozzle disturbance:yes / no Time needed for stabilisation: . Automatic energy shutdown: Lack of gas:yes / no Lack of cooling water:yes / noLimits of error of measuring instruments: . % of set point (max. 5 %) Class 2,5 2):yes / noComments:.
