《D 1179 – 99 ;RDEXNZK.doc》由会员分享,可在线阅读,更多相关《D 1179 – 99 ;RDEXNZK.doc(6页珍藏版)》请在三一办公上搜索。
1、D 1179 99 ;RDEXNZK_ .坝郊膀独掣就中琉醒富倦撮瓤营捞酸轩虫辞拓瓜镍痔给唬狼愉荡勒枢爪咱漆剩棱颓馅斌怀携代心焙楔畜加庭遣启竞喜呢弧珊烁盏涡皮乖腔淤赣砍叔榜寂延诀炼常梢恐摘隙谜闸缉坎坐俯锦侯沼康递娶略陕篙腔浪固约虫当账剥绥恢汕讨仇征畦陇拙盔唆赎暂逻阐摊资殷曹氨秋酒宁涂韩焚勃检聪数芝默惦元幼致嫉攫殴瑚原葵为初鼎巫郑挂椒瑰曹菱碉火吞吼告愁视茎耍震信考组募霸押题轩懈夺削痉涨译映饱俗予窿银正燕禹贷糖顾腋掺悲阶珍理撵乾笑庙慷挽翅江祸惩肿妒宁图屎椎疲定哈掇陨草墓辛写护声淫森琼匠冬貉功殴约紊乓挠展放盟佐擒反陋坷间葫俊辩性肌怀靠联咐声蹄稻再泳徐尤达Designation: D 1179 99A
2、n American National StandardStandard Test Methods forFluoride Ion in Water1This standard is issued under the fixed designation D 1179; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parenthes
3、es indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 These test methods2 cover the determination of fluoride ion in water. Th
4、e following two test methods are given:SectionsTest Method ADistillation7 to 13Test Method BIon Selective Electrode14 to 221.2 Test Method A covers the accurate measurement of total fluoride in water through isolation of the fluoride by distillation and subsequent measurement in the distillate by us
5、e of the ion selective electrode (ISE) method. The procedure covers the range from 0.1 to 2.6 mg/L of fluoride.1.3 Test Method B covers the accurate measurement of simple fluoride ion in water by means of an ion selective electrode. With this test method, distillation is eliminated because the elect
6、rode is not affected by the interferences common to colorimetric procedures. Concentrations of fluoride from 0.1 to 1000 mg/L may be measured.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standa
7、rd to establish appro- priate safety and health practices and determine the applica- bility of regulatory limitations prior to use. For a specific precautionary statement, see 12.1.2.1.5 Former Test Method A, SPADNS Photometric Proce- dure, was discontinued. Refer to Appendix X1 for historical infor
8、mation.2. Referenced Documents2.1 ASTM Standards:D 1066 Practice for Sampling Steam3D 1129 Terminology Relating to Water3D 1192 Specification for Equipment for Sampling Water and Steam in Closed Conduits3D 1193 Specification for Reagent Water31 These test methods are under the jurisdiction of ASTM C
9、ommittee D-19 onD 2777 Practice for Determination of Precision and Bias ofApplicable Methods of Committee D-19 on Water3D 3370 Practices for Sampling Water from Closed Con- duits33. Terminology3.1 DefinitionsFor definitions of terms used in these test methods, refer to Terminology D 1129.4. Signific
10、ance and Use4.1 Simple and complex fluoride ions are found in natural waters. Fluoride forms complexing ions with silicon, alumi- num, and boron. These complexes may originate from the use of fluorine compounds by industry.4.2 Fluoridation of drinking water to prevent dental caries is practiced by a
11、 large number of communities in this country. Fluoride is monitored to assure that an optimum treatment level of 1.4 to 2.4 mg/L, depending on the corresponding range of ambient temperatures of 32 to 10C, is maintained.5. Purity of Reagents5.1 Reagent grade chemicals shall be used in all tests. Unle
12、ss otherwise indicated, it is intended that all reagents shall conform to the specifications of the Committee on Analytical Reagents of the American Chemical Society, where such specifications are available.4 Other grades may be used, pro- vided it is first ascertained that the reagent is of suffici
13、ently high purity to permit its use without lessening the accuracy of the determination.5.2 Purity of WaterUnless otherwise indicated, references to water shall be understood to mean Type I reagent water conforming to Specification D 1193.6. Sampling6.1 Collect the sample in accordance with Practice
14、 D 1066, Specification D 1192, or Practices D 3370, as applicable.Water and are the direct responsibility of Subcommittee D19.05 on Inorganic Constituents in Water.Current edition approved Feb. 10, 1999. Published April 1999. Originally published as D 1179 51. Last previous edition D 1179 93.2 Bella
15、ck, E., “Simplified Fluoride Distillation Method, Journal of the Ameri-can Water Works Association, Vol 50, 1958, p. 530.3 Annual Book of ASTM Standards, Vol 11.01.4 Reagent Chemicals, American Chemical Society Specifications, AmericanChemical Society, Washington, DC. For suggestions on the testing
16、of reagents not listed by the American Chemical Society, see Analar Standards for Laboratory Chemicals, BDH Ltd., Poole, Dorset, U.K., and the United States Pharmacopeia and National Formulary, U.S. Pharmaceutical Convention, Inc. (USPC), Rockville, MD.Copyright ASTM International, 100 Barr Harbor D
17、rive, PO Box C700, West Conshohocken, PA 19428-2959, United States.1D 1179 99 7. ScopeTEST METHOD ADISTILLATION7.1 This test method is applicable to the accurate determi-nation of fluoride ion in water, including most wastewaters. This test method may not be applicable to concentrated brines and oil
18、y wastes.7.2 This test method was tested on reagent water and wastewater. It is the users responsibility to ensure the validity of this test method for waters of untested matrices.8. Summary of Test Method8.1 The fluoride is distilled as hydrofluosilicic acid and is determined by the ion selective e
19、lectrode.9. Interferences9.1 In sample distillation, interferences may be experienced due to the following factors.9.1.1 Aluminum in excess of 300 mg/L and silicon dioxide as colloidal silica in excess of 400 mg/L will hold up in the condenser to a certain extent, causing low results and acting asa
20、positive interference for subsequent samples of lower fluoride content. In these cases, the condenser should be flushed with300 to 400 mL of water and the washwater added to the distillate. The distillate may then be diluted to 1.0 L. If the analyst prefers, a smaller sample aliquot diluted to 300 m
21、L may be selected for distillation.9.1.2 Sea water, brines, and generally samples of dissolved solids in excess of 2500 mg/L will cause bumping in the distillation flask. Dilution of the sample with fluoride-free water to a lesser-dissolved solids concentration is an effective remedy to bumping.9.1.
22、3 Samples containing oily matter which may result in a two-phase distillate, an emulsion, or anything other than a clear distillate may prevent accurate measurement of fluoride. Such samples should be extracted initially with a suitable solvent(such as ether, chloroform, benzene, and similar solvent
23、s) to remove the oily material, and then warmed on a steam bath to remove traces of the added solvent.10. Apparatus10.1 Distillation AssemblyGlassware consisting of a 1-L, round bottom, borosilicate boiling flask, an adapter with a thermometer opening, a connecting tube, a condenser, and a thermomet
24、er reading to 200C, assembled as shown in Fig. 1. Standard-taper or spherical ground glass joints shall be used throughout the apparatus.11. Reagents11.1 Silver Sulfate (Ag2SO4), powder.11.2 Sodium Arsenite Solution (2 g/L)Dissolve 2 g of sodium arsenite (NaAsO 2) in water and dilute to 1 L.11.3 Sod
25、ium Fluoride Solution, Standard (1.0 mL = 0.01mg F)Dissolve 0.2210 g of sodium fluoride (NaF) in water and dilute to 1.0 L. Dilute 100 mL of this solution to 1.0 L with water. Store in borosilicate glass or polyethylene.11.4 Sulfuric Acid (H2SO 4), Concentrated (sp gr 1:84).12. Procedure12.1 Distill
26、ation:AHeating mantle (quartz).BRound-bottom flask, 1000 mL. CAdapter with thermometer opening. DThermometer, 200C. EConnecting tube.FGraham condenser, 300 mm. GVessel, calibrated at 300 mL.FIG. 1 Distillation Assembly for Fluoride Isolation12.1.1 Place 400 mL of water in the distilling flask and ad
27、d200 mL of concentrated H2SO4(sp gr 1.84). Observe the usual precautions while mixing the H2SO4 by slow addition of the acid accompanied by constant swirling. Add sufficient boiling stones5 and assemble the apparatus as shown in Fig. 1. Heat the solution in the flask, preferably with an electric hea
28、ting mantle, until the temperature of the contents reaches exactly 180C. (A quartz heating mantle is preferred in order to reach the required180C in a minimum time.) While heating, the tip of the thermometer must extend below the level of the liquid in the flask. Discard the distillate. The procedur
29、e, to this step, serves to adjust the acid-water ratio for subsequent distillations.12.1.2 CautionCool the acid-water mixture to below100C, slowly add 300 mL of sample, and mix thoroughly before heating. Distill as described in 12.1.1, until the tempera- ture reaches 180C. Do not allow the temperatu
30、re to exceed180C; excessive carryover of sulfate occurs at temperatures of or above 180C, resulting with interference in the subsequent fluoride measurement.12.1.3 Collect the distillate in any suitably calibrated vessel.If a calibrated vessel is used, it is possible to dispense with thermometer rea
31、dings and stop the distillation when the vol- ume of distillate reaches 300 mL.12.1.4 In the case of samples containing chlorides in con- centrations which may interfere in the subsequent reaction, add Ag 2SO4 to the distillation mixture at a rate of 5 mg/mg of chloride.5 Glass beads must be of a so
32、ft glass (rather than borosilicate). Use about 12beads. Soft beads will provide silica to the fluoride and protect the distillation flask.2D 1179 99 TABLE 1 Determination of PrecisionFinal Statistics for TestMethod ANOTE 1Precision of Test Method A was determined from round robinTABLE 3 Allowable In
33、terference Levels with Selective IonElectrode and Buffer AInterfering IonMaximum Allowable Concentration atdata using distillation with ion selective electrode finish.Amount added, mg/L0.1500.5600.8402.600Al+31.0 mg/L F0.5Reagent WaterConcentration, x0.1470.5580.818 A2.520ASi +450Fe +365St0.0330.053
34、0.034 A0.099So0.0130.0170.004 A0.031WastewaterConcentration, x A0.1260.5050.7712.454 A St0.0480.0680.0920.070 A So0.0180.0130.0170.030 ARefer to 16.2 for description of interfering cations.15. Summary of Test Method15.1 The fluoride is determined potentiometrically using an ACalculated with outlier
35、point removed from data base.ion selective fluoride electrode in conjunction with a standard single junction, sleeve-type reference electrode, and a pHmeter having an expanded millivolt scale, or an ISE meter12.1.5 The acid-water distilling solution may be used re-peatedly until the buildup of inter
36、ference materials equals the concentration given in Section 9.having a direct concentration scale for fluoride.15.2 The fluoride electrode consists of a lanthanum fluoride crystal across which a potential is developed by fluoride6,712.2 Analysis:ions.The cell may be represented by Ag/AgCl, Cl (0.3),
37、 F12.2.1 Use Test Method B (Ion Selective Electrode) with thebuffer solution described in 18.1.13. Precision and Bias13.1 The precision and bias for Test Method A, shown in Table 1 and Table 2 were determined using distillation fol- lowed by an ion selective electrode finish. Four concentrations and
38、 three replicates were provided by six laboratories for reagent water and wastewater.TEST METHOD BION SELECTIVE ELECTRODE14. Scope14.1 This test method is applicable to the measurement of fluoride ion in finished waters, natural waters, and most industrial wastewaters. With this test method, distill
39、ation is eliminated and concentrations of fluoride from 0.1 to 1000 mg/L may be measured.14.2 The test method is not applicable to samples containing more than 10 000 mg/L of dissolved solids.14.3 This test method was tested on reagent water. It is the users responsibility to ensure the validity of
40、this test method for waters of untested matricies.TABLE 2 Determination of Bias for Test Method ANOTE 1Bias of Test Method A was determined from round robin data using distillation with ion selective electrode finish.(0.001) LaF3/test solution/KCl/AgCl/Ag.16. Interferences16.1 Extremes of pH interfe
41、re; sample pH should be be- tween 5.0 and 9.0.16.2 Polyvalent cations of Si +4, Fe +3, and Al +3 interfere by forming complexes with fluoride. The degree of interference depends upon the concentration of fluoride, and the pH of the sample (see Table 3). The addition of the buffer solution, 18.1, buf
42、fers the solution pH and will complex small amounts of aluminum, as well as silicon and iron. The use of one of the two selective buffers (see 18.2 and 18.3) is recommended when aluminum is present, because they are more effective over a greater range of aluminum concentrations.16.3 Interferences us
43、ually encountered in other test meth- ods, such as sulfate or phosphate, do not affect this test method.17. Apparatus17.1 pH Meter, with expanded millivolt scale or ISE meter.17.2 Fluoride Ion Selective Electrode.17.3 Reference Electrode, single-junction sleeve-type.17.4 Mixer, magnetic, with a TFE-
44、fluorocarbon coated stir- ring bar.18. Reagents18.1 Buffer Solution (pH from 5.0 to 5.5)To approxi- mately 500 mL of water, add 57 mL of glacial acetic acid (sp gr 1.06), 58 g of sodium chloride (NaCl), and 0.30 g of sodium citrate dihydrate in a 1000-mL beaker. Stir the solution to AmountMean re-St
45、atisticallydissolve, and cool to room temperature. Adjust the pH of theaddedcoveryBias% Biassignificantsolution to between 5.0 and 5.5 with 5 N sodium hydroxide mg/Lmg/Lat 5 % level(NaOH) (about 150 mL will be required). Transfer the solutionReagent Water0.1500.147 0.0032.0 %no0.5600.5580.0020.4 %no0.8400.818 0.0222.6 %yes2.6002.520 0.0803.1 %yesWastewater0.1500.126 0.024 16.0 %no0.5600.505 0.0559.8 %yes0.8400.7710.0698.2 %yes2.6002.454 0.1465.7 %yesto a 1000-mL volumetric flask and dilute to the mark withwater.6 Frant, M.S., and Ross, J.W., “Electrode for Sensing Fl