《【BS英国标准word原稿】BS EN 1337102003 Structural bearings. Inspection and maintenance.doc》由会员分享，可在线阅读，更多相关《【BS英国标准word原稿】BS EN 1337102003 Structural bearings. Inspection and maintenance.doc（25页珍藏版）》请在三一办公上搜索。
1、 ，如果你需要更多标准可以到 如果你购买的文档存在缺页、字迹模糊、乱码等情况，请大家通过论坛消息与我联系。BRITISH STANDARD BS EN1337-10:2003Corrected and reprinted November 2003Structural bearings Part 10: Inspection and maintenanceThe European Standard EN 1337-10:2003 has the status of aBritish StandardICS 91.010.30 ，如果你需要更多标准可以到 如果你购买的文档存在缺页、字迹模糊、乱码
2、等情况，请大家通过论坛消息与我联系。BS EN 1337-10:2003National forewordThis British Standard is the official English language version ofEN 1337-10:2003.The UK participation in its preparation was entrusted to Technical CommitteeB/522, Structural bearings, which has the responsibility to:aid enquirers to understand th
3、e text;present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed;monitor related international and European developments and promulgate them in the UK.A list of organizations represented on this commit
4、tee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Sear
5、ch” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard does not of itself confer immunity from legal obli
6、gations.This British Standard, was published under the authority of the Standards Policy and Strategy Committee on24 July 2003 BSI 5 November 2003ISBN 0 580 42319 0Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 17, an inside back cover and
7、 a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amd. No.DateCommentsAmendments issued since publicationEUROPEAN STANDARD NORME EUROPENNEEUROPISCHE NORMEN 1337-10July 2003ICS 91.010.30English versionStructural Bearings - Part 10: Inspectio
8、n and maintenanceAppareils dappui structuraux - Partie 10: SurveillanceLager im Bauwesen - Teil 10: Inspektion undInstandhaltungThis European Standard was approved by CEN on 12 June 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for givi
9、ng this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions
10、 (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Czech R
11、epublic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATION C O M I T EUR O P EN DE NOR M A L I S A TI ON EUR O P I S C H ES KOM
12、I TEE F R NOR M UNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2003 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members.Ref. No. EN 1337-10:2003 EEN 1337-10:2003 (E)ContentspageForeword . 31Scope. 42Normative references . 43Definitions a
13、nd symbols. 44General requirements for regular and principal inspections . 55Regular inspection . 56Principal inspection . 67Servicing and replacement . 10Annex A (informative) Explanations . 11Annex B (informative) Report of inspection of bearings . 125ForewordThis document (EN 1337-10:2003) has be
14、en prepared by Technical Committee CEN /TC 167 Structural bearings, the secretariat of which is held by UNI.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2004, and conflicting national s
15、tandards shall be withdrawn at the latest by January 2004.The entire European Standard EN 1337 consists of 11 Parts listed here below: Part 1General design rulesPart 2Sliding elementsPart 3Elastomeric bearingsPart 4Roller bearingsPart 5Pot bearingsPart 6Rocker bearingsPart 7Spherical and cylindrical
16、 PTFE bearings Part 8Guide bearings and restraint bearings Part 9ProtectionPart 10Inspection and maintenancePart 11Transport, storage and installationAnnexes A and B are informative.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are
17、 bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and the United Kingdom.1ScopeThis European Standard applie
18、s to the inspection and maintenance of bearings designed in accordance with EN1337-1, when used in the construction of bridges or structures requiring similar bearing systems. It presupposes the existence of guidelines for the regular inspection of the whole structure during its service life.It may
19、also be used as appropriate for the inspection and maintenance of bearings designed and/or installed before the introduction of this European Standard.This European Standard specifies the aspects of each type of bearing that shall be inspected and recorded. It does not specify permissible values. Fo
20、r these reference shall be made to the relevant parts of this European Standard and to the drawings and design calculations for the bearing and the structure.NOTE 1Attention is drawn to the particular necessity for regular inspection and maintenance of bearings as, without such inspection and mainte
21、nance, premature failure may occur.NOTE 2National regulations may exist on the subjects covered by this European Standard and, therefore, they prevail on it.2Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. These normative ref
22、erences are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references th
23、e latest edition of the publication referred to applies (including amendments).EN 13371:2000, Structural bearings Part 1: General design rules.EN 133711: 1997, Structural bearings Part 11: Transport, storage and installation.3Definitions and symbolsFor the purposes of this European Standard the foll
24、owing terms and definitions apply:3.1 inspectionregular observation, noting and reporting3.1.1regular inspectionclose visual inspection without measurements, spaced at equal, resonably frequent, intervals3.1.2principal inspectionsimilar to a regular inspection but in more detail and including precis
25、e measurement3.2 maintenanceservicing and replacement3.2.1 servicingcleaning, greasing, painting and repair of minor defects3.2.2 replacementrenewal of major parts of a bearing or of the entire bearing3.3Symbolshprotrusion of PTFEvxdisplacement in the main direction of movement of the structurevydis
26、placement transverse to the main direction of movement of the structureaxangle of rotation in the main direction of movement of the structureayangle of rotation transverse to the main direction of movement of the structures1clearance to allow rotational movements2clearance between vertical surfacess
27、3clearance between guide surfacess4clearance of vertical movements of the structure4General requirements for regular and principal inspectionsThe condition of the bearings in a structure shall be checked visually, at least as often as the regular inspection of the structure (or failing this at the t
28、ime of the principal inspection) or if the construction work is not subject to regular inspection, by an inspector, with competent knowledge of bearings, at least as frequently as the structure is inspected. If it is necessary to enable the inspector to do this, bearings shall be cleaned prior to th
29、e inspection.The bearings should be inspected after an accidental collision with the bridge, such as an over-high vehicle colliding with the deck, or after an exceptional event, such as an earthquake.Should the inspector encounter conditions that he is unable to explain or detect fully, or for which
30、 he is unable to recommend remedial action, he shall seek, if need be, the assistance of a special expert before completing his report.Depending on the outcome of the inspection one of the following steps shall be undertaken:no action;further measurements of the movement capacity (under extreme temp
31、eratures, different loads, etc.);further test procedures;repair (corrections of the position, replacement of the entire bearing or of parts, renewal or supplement of the protection against corrosion or underneath packing with mortar, etc.).5Regular inspectionIn the regular inspection the following p
32、roperties shall be checked:a) sufficient capacity for residual movement with respect to the type of the bearing, taking into account the temperature of the structure;b) visible defects: cracks; incorrect position; unforeseen movements and deformations;c) condition of bedding and fixing;d) condition
33、of corrosion protection, dust protection and seals;e) condition of sliding and rolling surfaces;f)visible defects of adjoining structural parts.The results shall be recorded. An example is shown in annex B.4. The report shall be filed with plans and drawings of the structure.In case of visible defec
34、ts or damage which are likely to affect the function, checks according to clause 6 shall be carried out.6Principal inspection6.1 GeneralPrincipal inspections shall be carried out at less frequent intervals than regular inspections (see A.5) and will normally replace one of these. They are intended t
35、o result in a precise record of the condition of the bearing and, if properly interpreted and acted upon, will ensure that the bearing will continue to function as intended until the next principal inspection.It is recommended to carry out the first principal inspection within one year of the struct
36、ure being put into service and the results compared with the details recorded in accordance with clause 7 of EN 133711: 1997.The principal inspection shall include all the points covered by the regular inspection but in more precise detail. Points of particular importance for each type of bearing ar
37、e given below. Figures are also included showing the main dimensions to be recorded for each type of bearing. These shall be measured with dead load only on the structure whenever possible. If this is not feasible details of the live loading shall be provided as precisely as possible.The obtained me
38、asurements shall be compared with the design values. Hence the capacity of the bearing for all anticipated future movements and loads shall be checked.Type numbers in 6.2 correspond to the type numbers in EN 13371.6.2 Specific checks for the different types of bearings6.2.1Sliding part of bearings w
39、ith PTFE elements (see Figure 1)For the bearings No. 1.3, 1.4, 1.5, 1.7, 1.8, 2.2, 2.3, 3.3, 3.4, 3.5, 4.2, 4.3, 5.2, 5.3, 6.2, 7.3, 7.4 the protrusion h between the sliding surface and the plate containing the PTFE sheet shall be measured at sufficient points to find the minimum value; vx, vy and h
40、 to be recorded.Where visible the condition of the sliding surface and its fixings shall be reported.Figure 1 Sliding part of combined bearings176.2.2Elastomeric bearings and the elastomeric part of combined bearings (see Figure 2)For the bearings No. 1.1, 1.2, 1.3, 1.4, 1.5, 1.6, 1.7, 1.8 the visib
41、le surfaces shall be checked for cracks and excessive deformations. If cracks extend to the inner steel-plates of the bearing, the report shall inform the owners of this situation and of the risk of corrosion and failure of the product. Moreover, consideration shall be given to replacement of the bearing.ax, ay, vx and vy to be recorded.Figure 2 Elastomeric bearing6.2.3Single roller bearings (see Figure 3)For the bearings No. 6.1 and 6.2 the condition of the rolling surfaces, the continuity or otherwise of the line of contact, sloping
