《【BS英国标准】BS EN 46251996 无损检验—射线图像质量 第5部分 图像质量显示计(双线型)—图像不清晰度的测定.doc》由会员分享，可在线阅读，更多相关《【BS英国标准】BS EN 46251996 无损检验—射线图像质量 第5部分 图像质量显示计(双线型)—图像不清晰度的测定.doc（12页珍藏版）》请在三一办公上搜索。
1、国内外标准大全豆丁网国内外标准下载地址 BRITISH STANDARDNon-destructive testing Image quality of radiographsPart 5. Image quality indicators (duplex wire type), determination of image unsharpness valueThe European Standard EN 462-5 : 1996 has the status of aBritish StandardICS 19.100| BS EN462-5 : 1996|NO COPYING WITHO
2、UT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 462-5 : 1996Committees responsible for thisBritish StandardThe preparation of this British Standard was entrusted to Technical Committee WEE/46, Non-destructive testing, upon which the following bodies were represented:Aluminium FederationA
3、ssociation of Consulting Engineers BNF (Fulmer Materials Centre) British AirwaysBritish Chemical Engineering Contractors AssociationBritish Coal CorporationBritish Gas plcBritish Institute of Non-destructive Testing British Iron and Steel Producers Association British Nuclear Fuels plcBritish Railwa
4、ys BoardCastings Technology InternationalElectricity AssociationEngineering Equipment and Materials Users AssociationHealth and Safety ExecutiveInstitute of PhysicsInstitute of Quality Assurance Lloyds Register of Shipping Ministry of DefenceNational Radiological Protection BoardPower Generation Con
5、tractors Association (PGCA (BEAMA Ltd.) Railway Industry Association of Great BritainRoyal Society of ChemistrySafety Assessment Federation Ltd.Society of British Aerospace Companies Limited Society of Motor Manufacturers and Traders Limited United Kingdom Accreditation ServiceWelding InstituteThis
6、British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on15 November 1996BSI 1996The following BSI references relate to the work on this standard:Committee reference WEE/46Draft for co
7、mment 94/703765 DCISBN 0 580 26259 6The following body was also represented in the drafting of the standard, through subcommittees and panels:British Photographic AssociationAmd. No.DateText affectedAmendments issued since publicationBS EN 462-5 : 1996ContentsPage Committees responsible Inside front
8、 cover National foreword ii Foreword 2Text of EN 462-53BSI 1996iBS EN 462-5 : 1996ForewordThis British Standard has been prepared by Technical Committee WEE/46 and is the English language version of EN 462-5 : 1996 Non-destructive testing Image quality of radiographs Part 5 : Image quality indicator
9、s (duplex wire type), determination of image unsharpness value published by the European Committee for Standardization (CEN).EN 462-5 : 1996 was produced as a result of international discussions in which theUnited Kingdom took an active part.BS EN 462-5 : 1996, together with BS EN 462-1 : 1994, BS E
10、N 462-2 : 1994, BS EN 462-4 :1995 and BS EN 462-3 (in preparation) supersedes BS 3971 : 1980, which will be withdrawn when all the relevant Parts of BS EN 462 have been published.Cross referencesPublication referred to Corresponding British StandardEN 444 : 1994BS EN 444 : 1994 Non-destructive testi
11、ng General principles for radiographic examination of metallic materials by X- and gamma raysBS EN 462 Non-destructive testing Image quality of radiographsEN 462-1 : 1994BS EN 462-1 : 1994 Image quality indicators (wire type) Determination of image quality valueEN 462-2 : 1994BS EN 462-2 : 1994 Imag
12、e quality indicators (step/hole type) Determination of image quality valueCompliance with a British Standard does not of itself confer immunity from legal obligations.iiBSI 1996EUROPEAN STANDARDEN 462-5NORME EUROPE ENNEEUROPA ISCHE NORMMarch 1996ICS 19.100Descriptors: Non-destructive tests, industri
13、al radiography, photographic images, quality, image quality indicators, specifications, dimensions, utilizationEnglish versionNon-destructive testing Image quality of radiographs Part 5: Image quality indicators (duplex wire type), determination of image unsharpness valueEssais non destructifs Quali
14、te dimage des radiogrammes Partie 5: Indicateurs de qualite dimage (duplex a fils), de termination de lindice de flou de limageZersto rungsfreie Pru fung Bildgu te vonDurchstrahlungsaufnahmen Teil 5: Bildgu tepru fko rper (Doppel-Drahtsteg), Ermittlung der Bildunscha rfeThis European Standard was ap
15、proved by CEN on 1996-02-23. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning such national st
16、andards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified t
17、o the Central Secretariat has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.CENEu
18、ropean Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r NormungCentral Secretariat: rue de Stassart 36, B-1050 Brussels1996 Copyright reserved to CEN membersRef. No. EN 462-5 : 1996 EPage EN 462-5: 1996BSI 1996ForewordThis European Standard has been prepared
19、 byTechnical Committee CEN/TC 138, Non-destructiveContentsPagetesting, the secretariat of which is held by AFNOR. EN 462-5 is a Part of a series of European Standards;the other Parts are the following:EN 462-1Non-destructive testing Image quality of radiographs Part 1: Image quality indicators (wire
20、 type), determination of image quality valueEN 462-2Non-destructive testing Image quality of radiographs Part 2: Image quality indicators (step/hole type), determination of image quality valueEN 462-3Non-destructive testing Image quality of radiographs Part 3: Image quality classes for ferrous metal
21、sEN 462-4Non-destructive testing Image quality of radiographs Part 4: Experimental evaluation of image quality values and image quality tablesThis European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest bySeptemb
22、er 1996, and conflicting standards shall be withdrawn at the latest by September 1996.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany,
23、 Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.Foreword 21 Scope 32 Normative references 33 Definitions 34 Specification of duplex wire IQI35 Use of duplex wire 4Page 3EN 462-5: 19961 ScopeThis standard specifies a metho
24、d of determining the image unsharpness of radiographs and real-time radioscopic systems.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publ
25、ications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard onlywhen incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies.EN 444Non-des
26、tructive testing General principles for the radiographic examination of metallic materials with X- and gamma-raysEN 462-1 Non-destructive testing Image quality of radiographs Part 1: Image quality indicators (wire type), determination of image quality valueEN 462-2 Non-destructive testing Image qual
27、ity of radiographs Part 2: Image quality indicators (step/hole type), determination of image quality value3 DefinitionsFor the purposes of this standard, the following definitions apply.3.1 duplex wire image quality indicator (duplex wire IQI)An arrangement of pairs of wires as shown in figure 1.3.2
28、 image unsharpness valueThe number of the largest discernible element (see clause 5).The corresponding unsharpnesses are shown in table 1.4 Specification of duplex wire IQI4.1 Dimension/manufacture/marking4.1.1 Design/materialThe duplex wire IQI shall consist of a series of13 elements placed in a tr
29、ansparent rigid plastic holder, each element shall consist of a pair of wires of circular section. The elements 1D to 3D are of tungsten, the others of platinum.The dimensions shall be in accordance with figure 1.Dimensions in millimetresEnlarged view of each wire pair(element)Figure 1. Duplex wire
30、IQIPage EN 462-5: 1996BSI 19964.1.2 ManufactureTable 1. Element number, corresponding image unsharpness and wire diameterDimensions in millimetresElement no.(D = duplex)Corresponding unsharpnessWire diameterand spacing,dTolerances of wire diameter and wire spacing13D12D11D10D9D8D7D6D5D4D3D2D1D0,100,
31、130,160,200,260,320,400,500,640,801,001,261,600,0500,0630,0800,1000,1300,1600,2000,2500,3200,4000,5000,6300,8000,0050,010,02The wire diameters and spacing of the wires are shown in table 1.4.1.3 MarkingThe marking of the duplex wire IQI (see figure1) shall give the following information: EN 462-5.4.
32、2 Declaration of conformityThe manufacturer of this IQI shall provide a certificate of conformity with each duplex wire IQI.5 Use of duplex wireThe duplex wire IQI should be used in conjunction with a wire of step/hole type IQI. It shall be placed on the source side of the object being examined and
33、be aligned as closely as possible normal to the axis of the radiation beam.The image of the duplex wire IQI shall be examined with the aid of a magnifying glass up to 3 4. The largest element (i.e. pair of wires), the image of which has just merged from that of two separate wires into the single for
34、m without an identifiable space between the image of the two wires, is taken as the limit of discernibility. The image unsharpness U is given by 2d where d is the width of the wire and the wire spacing distance (see figure 1 and table 1).NOTE. The duplex wire IQI is no alternative for the wire of st
35、ep/hole type IQI because it relates only to unsharpness.BS EN 462-5 : 1996List of references (see national foreword)BSI389 Chiswick High RoadLondonW4 4AL| BSI British Standards Institution| BSI is the independent national body responsible for preparing British Standards. It| presents the UK view on
36、standards in Europe and at the international level. It is| incorporated by Royal Charter.| Revisions| British Standards are updated by amendment or revision. Users of British Standards| should make sure that they possess the latest amendments or editions.| It is the constant aim of BSI to improve th
37、e quality of our products and services. We| would be grateful if anyone finding an inaccuracy or ambiguity while using this| British Standard would inform the Secretary of the technical committee responsible,| the identity of which can be found on the inside front cover. Tel: 020 8996 9000.| Fax: 02
38、0 8996 7400.| BSI offers members an individual updating service called PLUS which ensures that| subscribers automatically receive the latest editions of standards.| Buying standards| Orders for all BSI, international and foreign standards publications should be| addressed to Customer Services. Tel:
39、020 8996 9001. Fax: 020 8996 7001.| In response to orders for international standards, it is BSI policy to supply the BSI| implementation of those that have been published as British Standards, unless| otherwise requested.| Information on standards| BSI provides a wide range of information on nation
40、al, European and international| standards through its Library and its Technical Help to Exporters Service. Various| BSI electronic information services are also available which give details on all its| products and services. Contact the Information Centre. Tel: 020 8996 7111.| Fax: 020 8996 7048.| S
41、ubscribing members of BSI are kept up to date with standards developments and| receive substantial discounts on the purchase price of standards. For details of| these and other benefits contact Membership Administration. Tel: 020 8996 7002.| Fax: 020 8996 7001.| Copyright| Copyright subsists in all
42、BSI publications. BSI also holds the copyright, in the UK, of| the publications of the international standardization bodies. Except as permitted| under the Copyright, Designs and Patents Act 1988 no extract may be reproduced,| stored in a retrieval system or transmitted in any form or by any means electronic,| photocopying, recording or otherwise without prior written permission from BSI.| This does not preclude the free use,
