《【英国标准word原稿】BS EN 12931999 General requirements for components used in pneumatically pressur.doc》由会员分享，可在线阅读，更多相关《【英国标准word原稿】BS EN 12931999 General requirements for components used in pneumatically pressur.doc（17页珍藏版）》请在三一办公上搜索。
1、豆丁网：BRITISH STANDARDGeneral requirements for components used in pneumatically pressurized discharge pipes, drains and sewersThe European Standard EN 1293:1999 has the status of aBritish StandardICS 23.040.01; 91.140.80; 93.030| BS EN1293:1999|第 5 页 共 17 页豆丁网：Licensed Copy: sheffieldun sheffieldun, n
2、a, Sat Oct 28 06:07:19 GMT+00:00 2006, Uncontrolled Copy, (c) BSI|NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 1293:1999National forewordThis British Standard is the English language version of EN 1293:1999.The UK participation in its preparation was entrusted by Techn
3、ical Committee B/505, Waste water engineering, to Subcommittee B/505/1, General requirements for pipes and fittings, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and
4、keep UK interests informed; monitor related international and European developments and promulgate them in the UK.A list of organizations represented on this subcommittee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publi
5、cations referred to in this document may be found in the BSI Standards Catalogue under the section entitled International Standards Correspondence Index, or by using theFind facility of the BSI Standards Electronic Catalogue.A British Standard does not purport to include all the necessary provisions
6、 of a contract. Users of British Standards are responsible for their correct application.Compliance with a British Standard does not of itself confer immunity from legal obligations.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 9 and a ba
7、ck cover.The BSI copyright notice displayed throughout this document indicates when the document was last issued.Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 06:07:19 GMT+00:00 2006, Uncontrolled Copy, (c) BSIAmd. No.DateCommentsThis British Standard, having been prepared under the directi
8、on of the Sector Committee for Building and CivilEngineering, was published under the authority of the Standards Committee and comes into effect on 15 August 1999BSI 08-1999ISBN 0 580 32934 8Amendments issued since publicationEUROPEAN STANDARDEN 1293NORME EUROPE ENNEEUROPA ISCHE NORMApril 1999ICS 13
9、.060.30; 23.040.01English versionGeneral requirements for components used in pneumatically pressurized discharge pipes, drains and sewersPrescriptions ge ne rales pour les composants utilise s dans les re seaux de vacuation, de branchement et dassainissement sous pression pneumatiqueAllgemeine Anfor
10、derungen an Bauteile von pneumatisch betirebenen AbwasserdruckleitungenLicensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 06:07:19 GMT+00:00 2006, Uncontrolled Copy, (c) BSIThis European Standard was approved by CEN on 16 December 1998.CEN members are bound to comply with the CEN/CENELEC Interna
11、l Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.T
12、his European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.CEN members are t
13、he national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.CENEuropean Committee for Standardization Comite Europe en de Normalisation E
14、uropa isches Komitee fu r NormungCentral Secretariat: rue de Stassart 36, B-1050 Brussels1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN nationalMembers.Ref. No. EN 1293:1999 EPage 9EN 1293:1999ForewordThis European Standard has been prepared by Technical
15、Committee CEN/TC 165, Waste water engineering, the Secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 1999, and conflicting national standards shall be wit
16、hdrawn at the latest by October 1999.This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s).This European Standard provides the basis for the preparation or revis
17、ion of product standards for discharge pipes, drains and sewers operating as pneumatically pressurized systems (see clause 1Scope)According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria,
18、 Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.BSI 08-1999ContentsPageLicensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 06:07:19 GMT+00:00 2006, Uncontroll
19、ed Copy, (c) BSI1Scope32Normative references33Definitions, symbols and abbreviations34Functional and dimensional requirements44.1Dimensions of pipes and fittings44.1.1Nominal sizes44.1.2Internal diameters and limit deviations44.2Geometry of pipes44.3Geometry of fittings54.3.1General54.3.2Bends54.3.3
20、Branches54.4Smoothness of bore54.5Appearance and soundness54.6Longitudinal bending moment resistance54.7Interconnection5Foreword 24.8Corrosion resistancePage54.9Abrasion resistance54.10Modification54.11Coatings and linings54.12Long-term behaviour54.13Durability54.14Sealing elements54.15Mechanical st
21、rength64.16Pressure classes for pipes, fittings and joints64.17Airtightness and watertightness64.17.1Seals for joints64.17.2Rigid joints64.17.3Adjustable joints64.17.4Flexible joints64.18Restrained joints64.19Temperature64.20Dimensional stability75Test methods75.1Measurement of diameters and wall th
22、icknesses75.1.1Mean internal diameter of barrels75.1.2Mean external diameter of barrels75.1.3Wall thickness of barrels75.2Measurement of deviation from straightness of barrels75.3Measurement of deviation from squareness of the ends of the pipes75.4Longitudinal bending moment resistance test for pipe
23、s75.5Crushing test for pipes with rigid behaviour75.6Stiffness test for pipes with flexible behaviour85.7Pressure tests85.7.1Tests for pipes85.7.2Test for joints85.7.3Test for restrained joints85.8Tests for fittings86Quality control87Marking8Annex A (informative) Examples for principles of pneumatic
24、ally pressurized wastewater systems 9Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 06:07:19 GMT+00:00 2006, Uncontrolled Copy, (c) BSI1 ScopeThis standard specifies general requirements for components for use in pneumatically pressurized discharge pipes, drains and sewers.This European Stan
25、dard provides the general basis for the preparation or revision of product standards. Some of the provisions may need modifications whendrafting harmonized European Standards. It is not applicable for the evaluation of products.It is applicable as a reference for drawing up a product specification,
26、if there is no product standard available.Components covered are pipes, fittings and joints. This European Standard includes marking, qualitycontrol and optional certification requirements.Components are those used in systems that convey in a satisfactory manner: domestic wastewater; rainwater and s
27、urface water; other waste waters (e.g. industrial wastewater)that will not damage the components.This European Standard applies equally to components which are factory-made and to those constructed on site, where applicable.2 Normative referencesThis European Standard incorporates by dated or undate
28、d reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard onlywhen inc
29、orporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies.EN 681-1, Elastomeric seals Material requirements for pipe joint seals used in water and drainage applications Part 1: Vulcanized rubber.prEN 681-2, Elastomeric seals Material r
30、equirements for pipe joint seals used in water and drainage applications Part 2: Thermoplastic elastomers.prEN 805:1996, Water supply Requirements for systems and components outside buildings.EN ISO 9001:1994, Quality systems Model for quality assurance in design, development, production, installati
31、on and servicing.(ISO 9001:1994)EN ISO 9002:1994, Quality systems Model for quality assurance in production, installation and servicing.(ISO 9002:1994)EN 45011, General requirements for bodies operating product certification systems.(ISO/IEC Guide 65:1996)EN 45012, General requirements for bodies op
32、erating assessment and certification/registration of quality systems.(ISO/IEC Guide 62:1996)ISO 48, Rubber, vulcanized or thermoplastic Determination of hardness (Hardness between10 IRHD and 100 IRHD).3 Definitions, symbols and abbreviationsFor the purposes of this standard, the following definition
33、s apply.3.1adjustable jointjoint which permits significant angular deflection at the time of installation but not thereafter3.2allowable maximum operating pressure PMAmaximum hydrostatic pressure including surge that a component can withstand from time to time in service3.3allowable operating pressu
34、re PFAmaximum hydrostatic pressure that a component can withstand continuously in service3.4allowable test pressure PEAmaximum hydrostatic pressure that a newly installed component can withstand for a relatively short duration when either fixed above ground level or laid and backfilled under-ground,
35、 in order to ensure the integrity and tightness of the pipeline3.5external diameter ODmean external diameter of the pipe barrel at any cross-section. For pipes with external profiles on the barrels, the external diameter is the maximum diameter when viewed in cross-section3.6factory production contr
36、olsurveillance mode in which a manufacturer performs its own surveillance on the result of its production according to a set of rules formally specified in quality assurance or quality management provision3.7flexible jointjoint which permits significant angular deflection, both during and after inst
37、allation and which can accept a slight offset of the centre line3.8 jointconnection between the adjacent ends of two components including the means of sealingLicensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 06:07:19 GMT+00:00 2006, Uncontrolled Copy, (c) BSI3.9mean internal diameter IDmean int
38、ernal diameter of the pipe barrel at any cross-section3.10nominal size DNnumerical designation of size of component, which is a convenient integer approximately equal to a manufacturing dimension in mm. This can apply to either the internal diameter (DN/ID) or the external diameter (DN/OD)3.11pipe b
39、arrelcylindrical part of the pipe with a uniform cross-section excluding socket and spigot3.12pneumatically pressurized systemsystem where flow is caused by pneumatic pressure and where the pipe normally operates full. The pneumatic pressure can be applied either as compressed air upstream or partia
40、l vacuum downstream3.13proof loadspecified test load which a component withstands where the related requirements of the product standard are met3.14quality control systemorganizational structure, responsibilities, procedures, processes and resources for implementing quality management3.15rigid joint
41、joint that does not permit significant angular deflection, either during or after installation3.16ring stiffnessresistance of a pipe to diametrical deflection in response to external loading applied along one diametric plane is given as follows:S = EI Dm3whereS is the ring stiffness of the pipe in k
42、ilonewtons per square metre;E is the modulus of elasticity in flexure in the circumferential direction in kilonewtons per square metre;I is second moment of area of the pipe wall in the longitudinal direction, per unit length, in metres to the fourth power per metre;Dm is the diameter of the neutral
43、 axis of the pipe wall, in metres.3.17ultimate loadthat load which causes failure of component (under test) which shall be as specified in product standards4 Functional and dimensional requirementsProduct standards may include specifications whichare more stringent, but not less stringent than those of this European Standard.4.1 Dimensions of pipes and fittings4.1.1 Nominal sizesNominal sizes DN shall be given in product standards as DN/ID or DN/OD.Nominal sizes specified in product standards should preferably be selected from Table 1 o
